Matrix VS-S13 Owner's Manual

[Page 1] Matrix VS-S13

OWNERS MANUAL Versa Single-Station Strength VS-S13 Converging Chest Press G1_OM_Chest Press Rev 1.1.indd 1 11/19/13 4:21 PM ...

[Page 2] Matrix VS-S13

3 Table Of Contents Safety, General Care & Maintenence ...............................................................3 Getting Started (Product Specifications) ........................................................5 Assembly Information .........

[Page 3] Matrix VS-S13

4 5 GETTING STARTED ACTION FREQUENCY Clean Upholstery Daily Inspect Cables Daily Clean Guide Rods Monthly Inspect Hardware Monthly Inspect Frame Bi-Annually Clean Machine As Needed Clean Grips As Needed Lubricate Guide Rods As Needed Upholstery &...

[Page 4] Matrix VS-S13

6 7 ASSEMBLY UNPACKING | TOOLS REQUIRED UNPACKING Thank you for purchasing a Matrix product. This machine is an EN957-1 and EN957-2 compliant Class S product. Your Ma- trix product is inspected before it is packaged. It is shipped in multiple pieces ...

[Page 5] Matrix VS-S13

8 9 Parts List ID DESCRIPTION QTY 1 M10 X 105L Socket Head Cap Screw 2 2 M10 Flat Washer 30 3 Narrow Cupped Flange 1 4 M10 Nylock Nut 10 5 Upper Connecting Tube 1 6 M10 X 20L Socket Head Cap Screw 6 7 Weight Stack Frame 1 8 User Frame 1 9 M10 X 125 S...

[Page 6] Matrix VS-S13

10 11 PART 1: WEIGHT STACK TO USER FRAME ASSEMBLY STEP 1 | WEIGHT STACK TO USER FRAME INSTRUCTIONS & NOTES ASSEMBLY 6 5 4 11 8 3 10 9 2 1 7 Fully tighten hardware to 77 N-m/57 ft-lbs. after weightplates have been assembled PART 2: ARM...

[Page 7] Matrix VS-S13

12 13 ASSEMBLY STEP 2 | RIGHT & LEFT ARM ASSEMBLY INSTRUCTIONS & NOTES PART 2: ARM ASSEMBLY 19 18 ID DESCRIPTION QUANTITY 18 M12 X 25L SHC 2 19 M12 Flat Washer 2 Install the pivot cap screw as shown. Torque all arm hardware to: • M12 f...

[Page 8] Matrix VS-S13

14 15 ASSEMBLY STEP 2 | WEIGHT STACK CABLE ASSEMBLY INSTRUCTIONS & NOTES PART 3: CABLE ASSEMBLY 29 28 25 26 27 ID DESCRIPTION QUANTITY 25 M8 X 50L SHC 1 26 Spacer 2 27 Cable Tie Rod End 1 28 M8 Flat Washer 2 29 M8 Nylock Nut 1 Fully thread ...

[Page 9] Matrix VS-S13

16 17 ASSEMBLY STEP 4 | USER FRAME CABLE ASSEMBLY INSTRUCTIONS & NOTES PART 3: CABLE ASSEMBLY 29 28 26 27 25 ID DESCRIPTION QUANTITY 25 M8 X 50L SHC 2 26 Spacer 4 27 Cable Tie Rod End 2 28 M8 Flat Washer 4 29 M8 Nylock Nut 2 *Note: Image sh...

[Page 10] Matrix VS-S13

18 19 STEP 1 | SHROUD ASSEMBLY ASSEMBLY INSTRUCTIONS & NOTES PART 5: PLASTICS ASSEMBLY ID DESCRIPTION QUANTITY 35 Front Shroud 1 36 Rear Shroud (Not shown) 1 ASSEMBLY ASSEMBLY Install the weight stack shrouds as shown. 35 Position hangers in ...

[Page 11] Matrix VS-S13

20 21 STEP 3 | TOP CAP COVERS INSTRUCTIONS & NOTES ID DESCRIPTION QUANTITY 40 Top Cap Cover 2 40 40 ASSEMBLY PART 5: PLASTICS ASSEMBLY Install the top cap covers. STEP 2 | TOP CAP ASSEMBLY INSTRUCTIONS & NOTES ID DESCRIPTION QUANTITY 37 M...

[Page 12] Matrix VS-S13

22 23 STEP 1 | PREMIUM KIT ASSEMBLY INSTRUCTIONS & NOTES PART 6: PREMIUM KIT ASSEMBLY 1. Remove the (2) top cap covers using a flat blade screw driver. 2. Remove the (4) M8 bolts and 20 mm diameter washers that hold the top cap to the weight ...

[Page 13] Matrix VS-S13

24 25 STEP 3 | PREMIUM KIT ASSEMBLY INSTRUCTIONS & NOTES PART 6: PREMIUM KIT ASSEMBLY 1. Remove and discard hole caps using caution not to scratch the paint. 2. Attach plug to Rep Counter. 3. Assemble Towel Hook (3P) and Rep Counter (2P) usi...

[Page 14] Matrix VS-S13

26 27 STEP 5 | PREMIUM KIT ASSEMBLY INSTRUCTIONS & NOTES PART 6: PREMIUM KIT ASSEMBLY 1. Remove the end caps using a 3 mm Allen wrench. 2. Cut off and discard the grips. 3. Remove inner collars with a 3 mm allen wrench. 4. Assemble the ASG gr...

[Page 15] Matrix VS-S13

28 29 PART 6: PREMIUM KIT ASSEMBLY Gas Shock ASSEMBLY STEP 7 | PREMIUM KIT ASSEMBLY INSTRUCTIONS & NOTES Raise the seat to the highest position before adding gas shock (6P) Shock must be positioned as shown with gas cyli...

[Page 16] Matrix VS-S13

30 31 STEP 1 | SHORT USER KIT ASSEMBLY INSTRUCTIONS & NOTES PART 7: SHORT USER KIT ASSEMBLY ASSEMBLY Assemble Short User Kit using the M10 hardware provided. Torque hardware to: 77 N-m/57 ft-lbs. ASSEMBLY PART 7: SHORT USER KIT ASSEMBLY OPTIONAL ...

[Page 17] Matrix VS-S13

Matrix Fitness 1600 Landmark Drive Cottage Grove WI 53527 matrixfitness.com Toll-free 866.693.4863 Facsimilie 608.839.8687 Versa Converging Chest Press Owners Guide Rev.1.1 Copyright © 2013 Matrix Fitness G1_OM_Chest Press Rev 1.1.indd 32 11/19/13...