Santa Fe Cycles Assembly Manual

Download or browse on-line these Assembly Manual for Santa Fe Cycles Bicycle.

Santa Fe Cycles Manual Information:

This manual for Santa Fe Cycles, given in the PDF format, is available for free online viewing and download without logging on. The guide contains 20 pages, and the size of the file at download is . The document type is Assembly Manual.

Download Manual

Summary of Contents:

[Page 1] Santa Fe Cycles

Santa Fe Cycles Assembly Guide Introduction Congratulations on your purchase of your new Santa Fe bicycle. You have purchased a bicycle that has many features and qualities. Please take a few minutes and read thr...

[Page 2] Santa Fe Cycles

TOOLS REQUIRED for the ASSEMBLY - Phillips Screwdriver - 10, 15mm wrench - 5, 6.. Allen wrench - 6” Adjustable wrench ...

[Page 3] Santa Fe Cycles

1) REMOVING PACKAGING - Carefully remove all packing material from bicycle and inspect the bike for missing parts or any damages which may have occurred during shipping. If damage is found, please take photo/s of the damage and email us as soon...

[Page 4] Santa Fe Cycles

L-R : Rear Rack, Pedals, Seat, Seat tube, Headlight with mounting screws ...

[Page 5] Santa Fe Cycles

Step 2- Remove black protective plastic caps from each wheel. ...

[Page 6] Santa Fe Cycles

Step 2 cont ...

[Page 7] Santa Fe Cycles

Step 3- Fit front wheel. Loosen nuts on each end of front axel Note: the locking axle L-washer, this latches onto the front fork ...

[Page 8] Santa Fe Cycles

Fit front wheel into the forks, do not tighten completely as the front basket mount bracket will go on here in a later step. Step 4. Handlebar assembly Step 4 cont. ...

[Page 9] Santa Fe Cycles

Slide off black cap from the bottom of stem and loosen handlebar stem bolt using allen key. Slide Handlebar assembly in to position on bike frame, align handlebar with the direction of front wheel. When satisfied with the positi...

[Page 10] Santa Fe Cycles

Step 5. Front Brakes. Loosen brake pad bolts using allen key. Rotate brake pads 90 degrees Unscrew brake lever adjuster nut shown , slide on to brake cable using the cam guide Note: for smoother pull on...

[Page 11] Santa Fe Cycles

Fit cable stop in to brake handle and guide through handle bracket, screw in cam guide. Squeeze brake calipers together and align brake pads with the wheel rim, tighten allen key bolts on brake pads. Fit brake cable elbo...

[Page 12] Santa Fe Cycles

STEP 6. Front Mudguard Slide mudguard in to place, make sure top mudguard bracket is aligned with hole at the back of the frame. Fit bolt ,flat washer and nut. Align rear chrome mudguard bracket with holes on l...

[Page 13] Santa Fe Cycles

STEP 8. Fit pedals to crank arm, screw in and tighten using 15MM spanner. ** pedals are marked L = Left hand side, R = Right hand side ** Note: Left pedal screws in Counter clockwise, Right pedal screws in clockwise ...

[Page 14] Santa Fe Cycles

STEP 10. SEAT ASSEMBLY. Disassemble seat bracket using allen key, please note order of disassembly. Insert seat into bracket,reassemble and tighten. Undo pull clamp on bike frame, insert seat post assembly in to bike frame....

[Page 15] Santa Fe Cycles

STEP 12. Fit bell assembly to Left side of handle bar assembly, making sure bell can be rung using left thumb while holding on to hand grip. STEP 13. FRONT BASKET ASSEMBLY. Align large chrome bracket low...

[Page 16] Santa Fe Cycles

STEP 13 Cont. Align basket assembly with bracket on bike frame headstem insert bolt through long slotted hole, put on the nut, do not tighten at this point. STEP 13 Cont. Align lower chrome bracke...

[Page 17] Santa Fe Cycles

STEP 14. REAR Rack/PARCEL HOLDER. Place parcel holder on bike frame. Align lower bracket holes with corresponding holes located above rear axle assembly, loosely tighten using hex headed bolts. Alig...

[Page 18] Santa Fe Cycles

STEP 15. HEADLIGHT ASSEMBLY. Fit headlight bracket to left hand side of front fork assembly, loosely tighten nuts, fit headlight to bracket. ** headlight assembly should fit in to position as indicated by bend on lower chrome b...

[Page 19] Santa Fe Cycles

BASIC MAINTENANCE You have made a wise decision on purchasing a SantaFe bicycle. To make sure that it stays in good condition for many years of service and riding pleasure, we suggest the following: CLEANING AND LUBRICATION Keeping your b...

[Page 20] Santa Fe Cycles

wheel, you will need to disconnect the front brake cable and brake arm from the fork. 2. Open the valve and squeeze the remaining air out of the tube. To open the valve, using a small screwdriver or tip of a tire lever, press on the valve ...