Dell D90D7 Installation Manual

[Page 1] Dell D90D7

Installation Guide Dell ® Wyse D Class, Wyse X Class, and Wyse Z Class Flash Upgrade Option Kit Products: D90D7, D90DW, X90m7, X90mw, Z90D7, Z90S7, Z90DE7, Z90DW, Z90SW Issue: 031214 PN: 883884-31L Rev. C ...

[Page 2] Dell D90D7

Copyright Notices © 2014, Dell Inc. All Rights Reserved. This manual and the software and firmware described in it are copyrighted. You may not reproduce, transmit, transcribe, store in a retrieval system, or translate into any language or computer...

[Page 3] Dell D90D7

Contents 1 Introduction 1 Kit Contents 1 Kit Warranty 1 Overview 1 Dell Technical Support 2 Related Documentation and Services 2 Dell Online Community 2 2 Installing D Class Flash 3 Requirements 3 Procedures 3 3 Installing X Class Flash 7 Requir...

[Page 4] Dell D90D7

iv Contents This page intentionally blank. ...

[Page 5] Dell D90D7

1 Introduction This guide provides step-by-step instructions to upgrade flash in the following products: • D Class: · D90D7 · D90DW • X Class: · X90m7 · X90mw • Z Class: · Z90D7 · Z90S7 · Z90DE7, · Z90DW · Z90SW Kit Contents The kit i...

[Page 6] Dell D90D7

2 Chapter 1 Dell Technical Support To access Dell technical resources, visit http://www.wyse.com/support. If you still have questions, you can submit your questions using the Self-Service Center at http://support.wyse.com/selfservice.html or call Cu...

[Page 7] Dell D90D7

2 Installing D Class Flash This chapter contains information for users of Wyse D class thin clients who must install new flash. Requirements • Small Phillips screwdriver WARNING: Flash modules may be susceptible to damage by Electro-Static Dischar...

[Page 8] Dell D90D7

4 Chapter 2 4. Place your thumbs on the top surface of the opposite end where the three screws were removed. With a continuous motion, push firmly downward and towards the back panel (pushing down unlatches the hooks under the cover). The cover wil...

[Page 9] Dell D90D7

Installing D Class Flash 5 Figure 4 Main board and Flash module 7. Remove the existing flash module. Locate the flash module and use the Phillips Screwdriver to remove its retaining screw as shown in Figure 5. Lift the flash module out of the sock...

[Page 10] Dell D90D7

6 Chapter 2 This page intentionally blank. ...

[Page 11] Dell D90D7

3 Installing X Class Flash This chapter contains information for users of Wyse X class mobile thin clients who must install new flash. Requirements • Small Phillips screwdriver WARNING: Flash modules may be susceptible to damage by Electro-Static...

[Page 12] Dell D90D7

8 Chapter 3 5. Remove the existing flash module. Locate the flash module and use the Phillips Screwdriver to remove its retaining screw as shown in Figure 7. Lift the flash module out of the socket. Figure 7 Removing the existing flash module 6. ...

[Page 13] Dell D90D7

4 Installing Z Class Flash This chapter contains information for users of Wyse Z class thin clients who must install new flash. Requirements • Small Phillips screwdriver WARNING: Flash modules may be susceptible to damage by Electro-Static Dischar...

[Page 14] Dell D90D7

10 Chapter 4 4. Place your thumbs on the top surface above where the end screws were removed. With a continuous motion, push firmly downward and towards the back panel (pushing down unlatches the hooks under the cover). The cover will shift approx...

[Page 15] Dell D90D7

Installing Z Class Flash 11 7. Remove the existing flash module. Locate the flash module and use the Phillips Screwdriver to remove its retaining screw as shown in Figure 11. Lift the flash module out of the socket. Figure 11 Removing the existin...

[Page 16] Dell D90D7

12 Chapter 4 This page intentionally blank. ...

[Page 17] Dell D90D7

5 Installing Firmware This chapter includes the requirements and procedures you need to install and use Wyse USB Firmware Tool to update your thin client to the firmware you need. TIP: The purpose of the USB Firmware Tool is to configure a bootable ...

[Page 18] Dell D90D7

14 Chapter 5 Procedures IMPORTANT: Complete the following procedures as an administrator (administrator privileges are required). Step 1: Download and Ready the Firmware You Require You must download and ready (extract) the firmware you want to use ...

[Page 19] Dell D90D7

Installing Firmware 15 Step 3: Use Wyse USB Firmware Tool to Configure a Single USB Key that will Push Firmware CAUTION: Complete the configuration procedures as an administrator. For Windows 7 Enterprise and Windows 7 Ultimate, right-click on Wyse ...

[Page 20] Dell D90D7

16 Chapter 5 Figure 15 Update firmware options - Windows Embedded Standard 7 example 4. Depending on the operating system of the firmware (from "Step 1: Download and Ready the Firmware You Require") that you will be pushing onto the targe...

[Page 21] Dell D90D7

Installing Firmware 17 Figure 17 Browse to select commandsXml.xml example 9. Navigate to the image folder (on your hard drive) that contains the firmware image you extracted (this is the location you selected in "Step 1: Download and Ready the...

[Page 22] Dell D90D7

18 Chapter 5 Step 4: Use the Configured USB Key to Install Firmware on Each Thin Client In this step, you will boot each target device you want to convert from the configured USB key so that the USB key will push the contents from the USB key onto ...

[Page 23] Dell D90D7

Installing Firmware 19 Troubleshooting This section contains general troubleshooting information. USB Keys - Troubleshooting Boot Issues Due to different manufacturing processes on USB keys (and the variety of them), not all brands have been tested ...

[Page 24] Dell D90D7

Installation Guide Dell ® Wyse D Class, Wyse X Class, and Wyse Z Class Flash Upgrade Option Kit Issue: 031214 Written and published by: Dell Inc., March 2014 Created using FrameMaker ® and Acrobat ® ...