ACME SPLENDOR 90 User Manual

Download or browse on-line these Operation & User’s Manual for ACME SPLENDOR 90 DJ Equipment.

ACME SPLENDOR 90 Manual Information:

This manual for ACME SPLENDOR 90, given in the PDF format, is available for free online viewing and download without logging on. The guide contains 17 pages, and the size of the file at download is . The document type is Operation & User’s Manual.

Download Manual

Summary of Contents:

[Page 1] ACME SPLENDOR 90

Splendor 90 CM-90 User Guide Professional Entertainment Technology ...

[Page 2] ACME SPLENDOR 90

TABLE OF CONTENTS 1. Safety Instruction 2. Technical Specification 3. Change Beam Angle 4. How To Set The Unit 4.1 Control Panel 4.2 Main Function 5. How To Control The Unit 5.1 Master/Slave Built-in Preprogram Function...

[Page 3] ACME SPLENDOR 90

1. Safety Instruction WARNING  Please keep this User Guide for future consultation. If you sell the unit to another user, be sure that they also receive this instruction booklet.  Unpack and check carefully there is no transpo...

[Page 4] ACME SPLENDOR 90

Caution There are no user serviceable parts inside the unit. Do not open the housing or attempt any repairs yourself. In the unlikely event your unit may require service, please contact your nearest dealer. Installation The unit should be moun...

[Page 5] ACME SPLENDOR 90

3. Change Beam Angle If you want to change the beam angle of the fixture, you can change lens of the fixture refer to the photo below: 4. How To Set The Unit 4.1 Control Panel Display To show the various menus and the se...

[Page 6] ACME SPLENDOR 90

Button MENU To select the programming functions DOWN To go backward in the selected functions UP To go forward in the selected functions ENTER To confirm the selected functions Fuse For over current protection. Only for rem...

[Page 7] ACME SPLENDOR 90

6A ...

[Page 8] ACME SPLENDOR 90

DMX Address Press the MENU button up to when the DMX Address is showing on the display. Press ENTER button and the display will blink. Use DOWN and UP button to change the DMX512 address. Once the address has been selected, press the ENTER button...

[Page 9] ACME SPLENDOR 90

ENTER button and the display will blink. Use DOWN and UP button to select the yes (yes blackout) or no (no blackout) mode. Once selected, press the ENTER button to store. Back to the main functions without any change press the MENU button or wait f...

[Page 10] ACME SPLENDOR 90

main functions without any change please press the MENU button. White Balance Press the MENU button up to when the White Balance is showing on the display. Press ENTER button and the Red will blink, press UP and Down button to adjust the value, pr...

[Page 11] ACME SPLENDOR 90

5. How To Control The Unit You can operate the unit in three ways: 1. By master/slave built-in preprogram function 2. By easy controller 3. By universal DMX controller 5.1 Master/Slave Built-in Preprogram Function By linking the uni...

[Page 12] ACME SPLENDOR 90

5.3 DMX Controller Use universal DMX controller to control the units, you have to set DMX address from 1 to 512 channel so that the units can receive DMX signal. Press the MENU button up to when the DMX Address is showing on the display. Press ...

[Page 13] ACME SPLENDOR 90

Ch1 Ch2 Ch3 Pan/Tilt Macro 16 Channel DMX512 Configuration(Mode2) Ch4 Ch5 Ch6 Pan Tilt Ch8 Function Macro Speed Ch7 Ch9 Ch10 Ch11 Green Blue Strobe Ch12 Ch13 Ch14 RedDimmer Ch16 Color Open Open Slow open fast close Slow close Fast open ...

[Page 14] ACME SPLENDOR 90

5.5 DMX512 Connection 1. If you using a controller with 5 pins DMX output, you need to use a 5 to 3 pin adapter-cable. 2. At last unit, the DMX cable has to be terminated with a terminator. Solder a 120 ohm 1/4W resistor between pin 2(DMX...

[Page 15] ACME SPLENDOR 90

6. Troubleshooting Following are a few common problems that may occur during operation. Here are some suggestions for easy troubleshooting: A. The unit does not work, no light and the fan does not work 1. Check the connection of power and m...

[Page 16] ACME SPLENDOR 90

Declaration of Conformity We declare that our products (lighting equipments) comply with the following specification and bears CE mark in accordance with the provision of the Electromagnetic Compatibility (EMC) Directive 2004/108/EC. ...

[Page 17] ACME SPLENDOR 90

Innovation, Quality, Performance 16A ...