ACME MH-575S User Manual

[Page 1] ACME MH-575S

RULER SPOT MH-575S User Guide Please read these instructions carefully before use 1- ...

[Page 2] ACME MH-575S

2- TABLE OF CONTENTS 1. Safety Instruction 2. Technical Specification 3. Lamp 4. How To Set The Unit 4.1 Control Panel 4.2 Main Function 4.3 Home Position Adjustment 5. How To Control The Unit 5.1 Master/Slave Built-In Prepr...

[Page 3] ACME MH-575S

4- moisture. l Never touch bulb with bare fingers, as it is very hot after using. l Hot lamp explosion hazard. Do not open the unit within five minutes after switching off. l Do not start on the unit without bulb enclosure or when housing is...

[Page 4] ACME MH-575S

6- Luminous intensity: Dimension: 425 x 556 x 372 mm Weight: 23 kg 2.1. Inserting/Exchanging rotating gobos DANGER! Install the gobos with the device switched off only. Unplug from ...

[Page 5] ACME MH-575S

8- 4. When burning, the lamp operates at high pressure and there is a slight risk of arc tube rupture. The risk increases with age, temperature and improper handling of the lamp. Do not use the lamp any longer than its specified life. 5. Ma...

[Page 6] ACME MH-575S

10- 11- DMX512 Address Setting Press the MENU button up to when the is shown on the display. Pressing ENTER button and the display will blink. Use DOWN and UP button to change the DMX512 address. Once the address has been select...

[Page 7] ACME MH-575S

12- Blackout Mode Press the MENU button up to when the is shown on the display. Pressing ENTER button and the display will blink. Use DOWN and UP button to select the (yes blackout) or (no blackout) mode. Once the ...

[Page 8] ACME MH-575S

14- Firmware version Press the MENU button up to when the is blinking on the display. Pressing ENTER button and the display will show the firmware version of the unit. To go back to the functions press the MENU button again. ...

[Page 9] ACME MH-575S

16- Focus Adjust Press the MENU button for at least 5 seconds into offset mode, use DOWN and UP button up to when the is shown on the display. Pressing ENTER button, the unit will focus on the center position. Use DOWN and UP button to adj...

[Page 10] ACME MH-575S

18- 5.3 DMX 512 Configuration 19- 5.4 DMX512 Connection 1. If you use a controller with 5 pins DMX connector, you need to use a 5 to 3 pin adapter. 2. At last unit, the DMX cable has to be terminated with a terminator....

[Page 11] ACME MH-575S

20- 6. Troubleshooting Following are a few common problems that may occur during operation. Here are some suggestions for easy troubleshooting: A. The unit does not work, no light and the fan does not work 1. Check the con...

[Page 12] ACME MH-575S

22- F. If The tilt belt is broken 1. Turn off the main power. 2. Unscrew all the screws (A) and open the right arm cover (B). 3. Unscrew the screws (C), the screws (D) and screws (E) that fix the bridge. 4. Change a new belt (F). Please ad...

[Page 13] ACME MH-575S

24- 7. Maintenance and Cleaning Maintenance: Anti-interference plate Ignitor Ballast A. As the pictures shown above, if the cable or cable joints turned yellow or black, please replace the cable or cab...

[Page 14] ACME MH-575S

26- 27- Innovation , Quality , Performance ...