JUKI HZL-DX series Instruction Manual

Download or browse on-line these Instruction Manual for JUKI HZL-DX series Sewing Machine.

JUKI HZL-DX series Manual Information:

This manual for JUKI HZL-DX series, given in the PDF format, is available for free online viewing and download without logging on. The guide contains 120 pages, and the size of the file at download is . The document type is Instruction Manual.

Download Manual

Summary of Contents:

[Page 1] JUKI HZL-DX series

Attention Please read this instruction manual before using the machine as it contains important operational and safety information. Keep this manual accessible so that you may refer to it at anytime while operating the machine. INSTRUCTION MAN...

[Page 2] JUKI HZL-DX series

...

[Page 3] JUKI HZL-DX series

1 “IMPORTANT SAFETY INSTRUCTIONS” When using an electrical appliance, basic safety precautions should always be followed, includ- ing the following: Read all instructions before using this sewing machine. “DANGER ____ To reduce the risk of el...

[Page 4] JUKI HZL-DX series

2 Danger warning which is not specied There is a risk of elec- trical shock There is a risk of re There is a risk of injury to hands, etc. Prohibit- ed matter which is not specied Disas- sembly/ alteration is prohibited Do not pl...

[Page 5] JUKI HZL-DX series

3 ● Do not wipe the sewing machine with solvent such as thinner. When the sewing machine is soiled, put a small quan- tity of neutral detergent on a piece of soft cloth and carefully wipe off the sew- ing machine with it. ● Be sure to use t...

[Page 6] JUKI HZL-DX series

4 “IMPORTANT SAFETY INSTRUCTIONS” .....1 Contents .........................................................4 Principal parts ................................................. 6 Accessories ....................................................7 Con...

[Page 7] JUKI HZL-DX series

5 Basic operations Practical sewing Patchwork quilt Decorative stitches Decorative stitches One-point stitch/sewing letters .....................74 Preparation before sewing ............................. 74 Test sewing ................................

[Page 8] JUKI HZL-DX series

6 Lock stitch button Principal parts Hand wheel (pulley) Power switch Machine-socket-inlet Foot-controller-jack Spool cap (large) Spool pin LCD Screen Operational buttons Face plate cover Threading lever Start/stop button Auxiliary bed (accessory ...

[Page 9] JUKI HZL-DX series

7 Draw the auxiliary bed out to the left. Accessories ● Inside the auxiliary bed. Quilt guide T-shape screwdriver Blind stitch presser foot (D) Ripper Zipper presser foot (B) Overcasting presser foot (C) Cleaning brush Eyelet punch Standard pr...

[Page 10] JUKI HZL-DX series

8 Connecting to the power supply Not-using foot-controller that using start/stop- button: 1. Turn OFF the power switch (turn to “O”) 2. Insert cord-connector into machine-socket-inlet. 3. Insert plug into socket-outlet. 4. Turn ON the power swi...

[Page 11] JUKI HZL-DX series

9 While sewing, speed can be adjusted. For straight stitch/zigzag stitch: The sewing machine performs reverse stitch as long as this button is held pressed. For other stitch types: The sewing machine performs lock stitch. When machine sto...

[Page 12] JUKI HZL-DX series

10 Presser foot to be used (marking) Stitch pattern Zigzag width Stitch length 2 Stitch length ad- justing dial 3 Conrmation button 6 Automatic lock stitch and thread trimming button 7 Float function button 8 Continuous stitch button 9 ...

[Page 13] JUKI HZL-DX series

11 1 Zigzag width adjustment dial This is used to change the zigzag width and the needle position. 2 Stitch length adjustment dial This is used to change the stitch length. In the case of the free motion, this dial is used for adjusting the pres...

[Page 14] JUKI HZL-DX series

12 Foot controller To run the machine, press the foot controller. The harder you press, the faster the machine sews. Speed controller will set the maximum sewing speed. Pressing harder → faster speed Pressing weaker → s...

[Page 15] JUKI HZL-DX series

13 The sewing speed at the start of sewing can be increased by using the option button. When the needle up/down switch is held pressed, the sew- ing machine performs sewing at a low speed. ★ Adjustable starting stitch speed ★ Low-speed inching ...

[Page 16] JUKI HZL-DX series

14 Presser foot lifting lever Lifting/lowering of the presser foot The presser foot is lifted/lowered with the presser foot lifting lever. The presser foot can be lifted higher than the ordinary lift position. This feature is useful when placi...

[Page 17] JUKI HZL-DX series

15 The knee lifting lever is useful when a guilt is being sewn and for other projects that require the use of both hands. With the knee lifting lever, you are able to control the position of the presser foot without using your hands. I...

[Page 18] JUKI HZL-DX series

16 Removing and installing the presser foot Removing and installing presser foot holder ★ Removing presser foot 1. Raise the needle and presser foot. 2. Press the presser foot releasing button to remove the presser foot. �...

[Page 19] JUKI HZL-DX series

17 The type and application of the presser foot Standard presser foot A This is used mainly for straight stitch and zigzag stitches. Use this presser foot especially when sewing heavy-weight materials. Zipper presser foot B This is used to attach...

[Page 20] JUKI HZL-DX series

18 Bobbin thread preparation Open the hook cover. Take out the bobbin. * If the bobbin has too little thread, do not use it as the thread will get tangled. * Use only the designated bobbin. Other bobbins may cause malfunction. 1 2 Taking out th...

[Page 21] JUKI HZL-DX series

19 Thread the guide A and then thread the thread guide (guide in the circle) for bobbin winding 1 Place the thread spool to the spool pin. 2 Winding the bobbin thread * An exclusive motor is built-in for winding bobbin so that you can wind bo...

[Page 22] JUKI HZL-DX series

20 Put the bobbin in the bobbin case. * Place the bobbin so that thread winds counter- clockwise. Thread groove A and B by pulling the thread end. * It will be easier to thread grooves when you press the bobbin lightly with your nger. Thread...

[Page 23] JUKI HZL-DX series

21 Thread to guide D and E leave the thread underneath. (Thread guide E first and it will thread to guide D as well.) * When pulling bobbin thread, bobbin rotates counterclockwise. If bobbin rotates clockwise, put the bobbin upside down....

[Page 24] JUKI HZL-DX series

22 1 Lift the presser foot lifting lever. 1 2 3 4 5 Make sure to push the needle to the top. It is impossible to perform stitching if the needle is not correctly installed or a bent needle is used. Pay close at- tention as this will cause ma- chi...

[Page 25] JUKI HZL-DX series

23 Thread to guide A . Hold the thread end and thread according to the arrow marking. * Make sure that the presser foot is raised. Otherwise the machine is not correctly thread- ed. 3 4 Thread the guide B from the right-hand side. Draw the n...

[Page 26] JUKI HZL-DX series

24 Release the threading lever and the needle thread is threaded to the needle eye. 1 Lower the presser foot. * The automatic needle threader sometimes fails to thread the needle when the presser foot is raised. 2 Thread to A and cut the thre...

[Page 27] JUKI HZL-DX series

25 Basic operation: You can start to sew without pulling up the bobbin thread, however, if you want to sew with the bob- bin thread pulled out, follow the directions below. Pull out both needle and bobbin threads by approx. 10 cm (4 inches) long an...

[Page 28] JUKI HZL-DX series

26 Attaching the needle Needles to be purchased When purchasing spare needles, specify HA X 1 (130/705H) or HA X 1 SP (needle for knits) . Checking the needle Check the needle for its straightness occasionally. Any bent needle would cause skippe...

[Page 29] JUKI HZL-DX series

27 Fabric, thread and needle table Fabric Thread Needle HA×1 Light-weight materials Lawn Silk thread ………………………………………… No.80,90 Spun thread ……………………………………… ...

[Page 30] JUKI HZL-DX series

28 How to adjust thread tension When the needle thread is too strong: The bobbin thread will be pulled to the front side of the fabric. Turn the thread tension adjustment dial towards "-1" to "-3". When the needle thread is to...

[Page 31] JUKI HZL-DX series

29 How to adjust presser foot pressure Turn the presser foot pressure adjustment dial to set the proper pressure. When sewing in general, set the presser foot pressure adjustment dial to “5”. When sewing on light synthetic fabrics, stretchy ...

[Page 32] JUKI HZL-DX series

30 Changeover of needle holes (straight stitch slide plate) Patterns which can be used with the straight stitch selection After you have changed the needle hole to the needle hole for straight stitches, press to display the patterns that can b...

[Page 33] JUKI HZL-DX series

31 Push and check the stitch pattern in this portion and select. Push and select a pattern type from with select button ( or ). Then, select a pattern with its pattern number. Select stitch pattern by number. Pattern can also be selec...

[Page 34] JUKI HZL-DX series

32 Pattern Refer to page 68 ~ 70, 72 Pattern No. 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 Pattern Application Standard buttonholes 2-step buttonhole Rounded end Keyhole buttonholes For knit Decorative Refer to page 49 ~ 56 Pattern Refe...

[Page 35] JUKI HZL-DX series

33 Push and select a pattern type from with select button ( or ). Then, select a pattern with its pattern number. The pattern types are same with those of "Quilt patterns", "Decorative patterns 1" and "Decorative pat...

[Page 36] JUKI HZL-DX series

34 Push and check the stitch pattern in this portion and select. DX5 How to select a stitch pattern ☆ There are 185 types of stitch patterns. ☆ When turning on the machine, the straight stitch of the center needle position is chosen automat...

[Page 37] JUKI HZL-DX series

35 Pattern No. 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 Pattern Application Standard buttonholes 2-step buttonhole Rounded end Keyhole buttonholes For knit Decorative Refer to page 49 ~ 56 ・ Buttonhole patterns Pattern Refer to page ...

[Page 38] JUKI HZL-DX series

36 Push and select a pattern type from with select button ( or ). Then, select a pattern with its pattern number. The pattern types are same with those of "Quilt patterns" and "Decorative patterns". “Quilt patterns” n...

[Page 39] JUKI HZL-DX series

37 Straight stitch Sewing start Pull the needle and bobbin threads under the presser foot to the rear of the machine and lower the presser foot to start sewing. Sewing end Stop sewing and push the thread trimming button to trim the threads...

[Page 40] JUKI HZL-DX series

38 When sewing the edge of thick fabrics Turn the hand wheel and let the needle enter at the posi- tion of sewing start. Push the black button A by nger and lower the presser foot. Release the finger from the black button and start se...

[Page 41] JUKI HZL-DX series

39 Lock stitch after sewing-end <When start/stop button is used> After the sewing is nished, push the reverse stitch button. While it is pressed, the machine will sew reverse and when it is released, the machine will stop sewing reverse. &...

[Page 42] JUKI HZL-DX series

40 Example: straight stitch B Fabric A The sewing machine operates differently according to the button you press. B : Press the reverse stitch button. The machine sews reverse stitches, stop sew- ing and trim both needle and bobbin threads aut...

[Page 43] JUKI HZL-DX series

41 When changing the needle position of straight stitch It is possible to change the needle position with the zigzag width adjusting dial/button. Turning to the left (- side), the needle moves to the left. Turning to the right (+ side), the needle ...

[Page 44] JUKI HZL-DX series

42 Reinforced stretch stitch The reinforcing stretch stitch helps reinforce seams when used for sewing of elastic fabric or the force-exert- ed part of fabric that is likely to fray. Straight stitch for elastic fabric Finished seams are elast...

[Page 45] JUKI HZL-DX series

43 Zigzag stitch When changing the zigzag width The zigzag width can be adjusted while sewing. Turning to the left (- side), displayed value becomes smaller and the zigzag width becomes smaller accordingly. Turning to the right (+ side), displayed v...

[Page 46] JUKI HZL-DX series

44 Pattern No. Practical 07 Presser foot Overcasting presser foot (C) Push the fabric towards the guide and sew. If the fabric and guide are apart, it will not make a nice stitch formation. Make sure to guide the fabric along the gui...

[Page 47] JUKI HZL-DX series

45 This stitch is used to prevent the cut edge of fabric from fraying. Keep some seam allowance and cut the sewn fabric carefully so that stitches are not cut by the scissors. Overcasting by 3-point zigzag Pattern No. Practical 05 Presser ...

[Page 48] JUKI HZL-DX series

46 Blind stitch Fabric (wrong side) Fabric (wrong side) Basting line Fabric (wrong side) 0.5 to 0.6 cm Fabric (wrong side) Finish line Finish line 0.5 to 0.6 cm Finish line 1 Sewing overcasting stitches on the edge of fabric. ● Refer to page ...

[Page 49] JUKI HZL-DX series

47 Finish line Fabric (right side) Fabric (wrong side) Fabric (wrong side) Guide Fabric (wrong side) Folded edge Guide Needle Folded edge Guide 4 Align the guide of the presser foot with the folded edge. Turn the hand wheel and adjust with th...

[Page 50] JUKI HZL-DX series

48 Turn the zigzag width adjusting dial to the right side. 2. If the stitches fail to reach the folded edge 1. If the stitches reach too far beyond the folded edge When changing the needle entry point Turn the handwheel to check the needle entry...

[Page 51] JUKI HZL-DX series

49 Buttonhole stitches Buttonhole type * The buttonhole length is automatically determined only by placing a button on the buttonhole press- er foot. * The machine can sew buttonholes for buttons with diameters of 0.7 - 3.2 cm. * In case of stre...

[Page 52] JUKI HZL-DX series

50 Groove Button holder 1 Set the presser foot. Lift the needle and lift the presser foot. Align the groove of the presser foot holder with the pin of the presser foot and lower the presser foot holder to set. 2 Set the button. Pull the button hold...

[Page 53] JUKI HZL-DX series

51 4 Place the fabric under the presser foot. Raise the presser foot, pass the needle thread through the hole on the presser foot and pull it out sideways. Place the fabric under the presser foot, align the mark- ing with the sewing-start point. Pe...

[Page 54] JUKI HZL-DX series

52 Eyelet punch It will be easier to sew buttonholes on the thin fabrics and/or near the overlapped sections, if the clamping plate is used. Clamping plate 1. Attach the buttonhole presser foot to the presser foot holder, with the clamping pla...

[Page 55] JUKI HZL-DX series

53 Hook Buttonholes with gimp thread prevent the buttonholes from stretching and can make them more secure. * A buttonhole with gimp thread should be sewn using the double bartack pattern (Pattern No. Direct 0). 1 Pass the needle thread through und...

[Page 56] JUKI HZL-DX series

54 Turn the zigzag width adjusting dial/button. Turn the stitch length adjusting dial/button. * The setting of the buttonhole width and stitch length will be cancelled when the power is shut down or anoth- er pattern is selected. Turn to the lef...

[Page 57] JUKI HZL-DX series

55 Manual 2-step buttonhole 1 Set the manual buttonhole presser foot (I). 2 Pass the needle thread through the hole of the presser foot and pull it out sideways together. Hole on the presser foot sewing start point Needle thread 3 Bring down the...

[Page 58] JUKI HZL-DX series

56 5 Push reverse stitch button when it comes to the sewing start point. Sewing start point Stopper pin 6 Sew bartack and lock stitches until the machine stops automatically. 7 Pierce a stopper pin at the bartack and open the buttonhole with a r...

[Page 59] JUKI HZL-DX series

57 Sewing buttons Pattern No. Practical 21 DX7 Practical 20 DX5 Presser foot Manual buttonhole presser foot (I) * Do not use the automatic thread trimming function when sewing buttons. 1 Move the drop feed knob to the right hand side. Feed d...

[Page 60] JUKI HZL-DX series

58 Bartacking Bartacking is used to reinforce the part of the seam that is likely to ravel. * The length of the bartack is determined by pushing the reverse stitch button, but it will automatically make a u-turn when it reaches the maximum of 20 s...

[Page 61] JUKI HZL-DX series

59 To sew a bartack of the same length again… when the length of the rst bartack has been memorized, ● When the start/stop button is pushed, the machine starts to sew and makes a u-turn automatically at the same point as the rst barta...

[Page 62] JUKI HZL-DX series

60 Inserting zippers * Make sure to use center needle position (Stitch pattern No. Direct 1). (right) (left) 2 Attach the zipper presser foot (B) to the machine. When sewing the left side of the zipper, place the zip- per under the right portion ...

[Page 63] JUKI HZL-DX series

61 5 cm 0.7 to 1 cm Basting Reverse stitches Basting stitches Zipper Fabric (wrong side) Fabric (right side) Fabric (right side) 5 cm 0.3 cm Slider Move up the slider 1 Open the seam allowance. Neatly open the seam allowance. Adjust the back ...

[Page 64] JUKI HZL-DX series

62 Presser foot holder Narrower sewing lines Quilt Guide Wider sewing lines How to use the quilt guide 2 Sew while tracing the stitches with the tip of the quilt guide. Distance between sewing lines can be adjusted freely. 1 Insert the quilt guid...

[Page 65] JUKI HZL-DX series

63 Scallop stitches This stitch is used for decorating edging on items such as table cloths, collars on blouse, etc. 1 To keep the pattern intact, leave some margin and sew on the edge of the cloth. 2 Cut the sewn fabric carefully so that stit...

[Page 66] JUKI HZL-DX series

64 Example) Decorative stitches Pattern No. Decorative 1: 01~80 DX7 Decorative 2: 01~80 DX7 Decorative: 01~90 DX5 Presser foot Manual buttonhole presser foot (I) Display of the length of one cycle Although the length of one cycle of the d...

[Page 67] JUKI HZL-DX series

65 Combination of patterns Patterns which can be combined (How to sew a combination of patterns) 2 Select the pattern No. 71. Sew the pattern No. 71 while aligning the inner edge of the presser foot with the edge of the pat- tern ( A ). 1 Sew...

[Page 68] JUKI HZL-DX series

66 Attention Turn OFF the power switch before replacing the presser foot. Patchwork piecing To sew pieces of cloth together is called piecing in patch- work. When piecing, the seam allowance is usually 1/4" (6.4 mm). 1 Cut the fabric ...

[Page 69] JUKI HZL-DX series

67 Appliqué (1) The edge of the appliqué fabric is sewn with a compact zig- zag, so it is suitable for the appliqué of cut fabric. 2 Turn the hand wheel towards you and start sewing along with the outer side of the appliqué fabric. 1 Cut the ap...

[Page 70] JUKI HZL-DX series

68 Appliqué (2) To make the stitch unconspicuous, an appliqué can be sewn. Seam allowance 2 Put the pattern paper onto the wrong side of the fabric and fold the seam allowance at the nish line. 1 Cut the appliqué fabric with seam allowance o...

[Page 71] JUKI HZL-DX series

69 Pattern No. Quilting 03~80 DX7 Quilting 03~50 DX5 Presser foot Manual buttonhole presser foot (I) Open toe presser foot (O) DX7 Only Crazy quilt Example 1) Quilting 54 Sew patterns so that they extend over both pieces of fabric. Using a d...

[Page 72] JUKI HZL-DX series

70 Stitch in ditch quilting Pattern No. Direct 1 DX7 Quilting 40 DX5 Quilting 36 Presser foot Edge sewing presser foot (R) This is separately available for DX5 This is for quilting the edge of patchworks and appliqués. The machine will sew...

[Page 73] JUKI HZL-DX series

71 * To further avoid fabric shifts, set the presser foot pressure lower. Adjustment of presser foot pressure: Refer to page 29. Setscrew for presser foot holder Actuating lever Needle clamp 1 Put top layer of fabric with patchwork and/ or ap...

[Page 74] JUKI HZL-DX series

72 1 Put top layer of fabric with patchwork and/ or appliqué, quilting cotton and bottom fabric together by using pin or basting stitches. 2 Assemble the quilt presser foot. Raise the presser bar. Loosen the setscrew for press- er foot holder and ...

[Page 75] JUKI HZL-DX series

73 4 Place the fabric underneath the presser foot and lower the presser foot. 5 Adjust the presser foot height according to the material thickness. The height can be adjusted in two different ways. ① I n the case of free motion (Pattern No. Qui...

[Page 76] JUKI HZL-DX series

74 Pattern No. - Presser foot Manual buttonhole presser foot (I) One-point stitch/sewing letters (in order to sew a pattern neatly, apply interlining and conduct a test sewing rst.) Use an iron to attach a fusible interlining to the wr...

[Page 77] JUKI HZL-DX series

75 Presser foot to be used (symbol) Sewing pattern Zigzag width Length of stitch Stitch length adjusting dial Conrmation button Continuous stitch but- ton Mirror image button Option button Selection button Zigzag width adjusting dial Clear butt...

[Page 78] JUKI HZL-DX series

76 Press . Press . Press . Press or to select . Press or to select . How to select pattern (letters) Press . Example: JUKI For DX5 , different selection screen and pattern number are used. Press and . (Pattern No. 31) Pre...

[Page 79] JUKI HZL-DX series

77 Press . Press or to select . Press . Press . Press and . (Pattern No. 31) When you want to change the size of pattern (letters) ….. Move the cursor to the desired pattern (letter). You can change the height and width by: Hei...

[Page 80] JUKI HZL-DX series

78 Change to . Press , and move the ‘_’(cur- sor) to the position where you wish to delete. By pressing , the pattern on the cursor “ " will be deleted. Press . How to edit patterns (letters) JUKI JUKI Press . Exa...

[Page 81] JUKI HZL-DX series

79 Pass down the needle thread through the presser foot hole and draw it sideways. Place the fabric underneath the presser foot and start. The machine will stop automatically when sewing is nished. Notes: 1. Note that the sewing speed varies ac...

[Page 82] JUKI HZL-DX series

80 The letters and one point patterns can be combined and saved for later use. There are 10 folders in total for saving. Press . Use to select folder to save and press . Notes: means there exists already a pattern. means empty and availa...

[Page 83] JUKI HZL-DX series

81 To delete the content stored inside a folder. Use to select the target folder where con- tent to be deleted is stored. Press . Use to select “de- lete” and press . Press . Press . To sew patterns continuously A combination of...

[Page 84] JUKI HZL-DX series

82 Character selecting methods No. of pressing a button 1 2 3 4 5 6 7 8 9 10 11 12 13 14 @ ! & ’ ( ) , . ? - ・ / : ; A B C a b c D E F d e f G H I g h i J K L j k l M N O m n o P Q R S p q r s T U V t u v W X Y Z w x y z _...

[Page 85] JUKI HZL-DX series

83 Type and usage of options Type of options Default setting If a pattern is selected again If the pow- er is turned OFF and re-turned ON 1 Changing the seam width of buttonhole The seam width of buttonhole is changeable. Standard The curr...

[Page 86] JUKI HZL-DX series

84 1 Change of seam width of buttonhole The seam width of buttonhole is changeable. * It is changeable when sewing a buttonhole. Small Standard Large * Default setting is “standard”. Example) narrowing (reducing) the seam ...

[Page 87] JUKI HZL-DX series

85 2 Change of needle position You can change the stitch base line. * Default setting differs with pattern. It is now changed to left needle position. * In case of a combined stitch pattern, if the needle po- sition is changed, the needle position...

[Page 88] JUKI HZL-DX series

86 Press . 3 Selecting the stop position of needle You can select the needle position (needle-up or needle-down) when the sewing machine stops. * Default setting is the needle-down stop. Example) To set the needle position when the sewing machin...

[Page 89] JUKI HZL-DX series

87 4 Twin needle sewing By using two needles beautiful decorative stitches can be sewn. * When using twin needles, make sure to set twin nee- dle sewing in Option and perform test sewing. * When twin needle sewing, make sure to use thread si...

[Page 90] JUKI HZL-DX series

88 Press . * Twin needle setting can not be done while a stitch pattern other than those for twin needle sewing is selected. mark will be shown. The twin needle setting can only be carried out when suitable pattern is selected and cen...

[Page 91] JUKI HZL-DX series

89 The foot switch function has now been set. * The setting is memorized even when the machine is turned off and on. 5 Foot switch function Press . Press or to select . Then, press . Select the function using and press . Reverse st...

[Page 92] JUKI HZL-DX series

90 6 Presser foot pivot function You can select the setting where the presser foot goes up with the needle held in the needle-down stop position when you stop the sewing machine. Example) To set the presser foot pivot function to OFF * Default set...

[Page 93] JUKI HZL-DX series

91 7 Setting the pivot height You can set the presser foot height in the case of using the pivot function. Setting range: 2.0 - 6.0 mm (in increments of 1 mm) * Default setting is 2.0 (mm). Example) To set the pivot height to 3.0 (mm) The pivot heig...

[Page 94] JUKI HZL-DX series

92 8 Setting the oat-function height You can set the presser foot height when pressing the oat function button. Under this mode, the straight stitch (Pattern No. 1) is automatically selected. Setting range: 0.0 - 2.5 mm (in increments of 0.1...

[Page 95] JUKI HZL-DX series

93 9 Setting of the presser foot lifting after thread trimming You can select the setting were the presser foot goes up automatically after the completion of thread trimming. Example) To set the function to lift the presser foot after thread trimmin...

[Page 96] JUKI HZL-DX series

94 !0 Adjusting the darning This function is used for adjusting the pattern shape. Adjustable range: -30 - 30 Press . Example) Press . Adjust the pattern while carrying out test sewing. Pattern adjustment has now been completed. * The setting...

[Page 97] JUKI HZL-DX series

95 !1 Adjustable starting stitch speed You can select the sewing speed to be employed at the start of sewing. Slow Standard Fast * Default setting is “Slow”. Example) To inc...

[Page 98] JUKI HZL-DX series

96 !2 Adjustable reverse stitch speed You can select the reverse stitch speed and lock stitch speed. Slow Standard Fast * Default setting is “Slow”. Example) To increase the...

[Page 99] JUKI HZL-DX series

97 !3 Guide The guide for winding bobbin thread, setting of bobbin, threading of needle thread, changing presser foot and needle can be seen on the LCD display. <Winding bobbin thread> <Changing presser foot> <Setting of bobbin&g...

[Page 100] JUKI HZL-DX series

98 !4 Adjusting the touch panel sensitivity You can adjust the touch panel sensitivity in ve steps. Setting range: 1.0 - 5.0 * Default setting is 3.0 Example) To increase the touch panel sensitivity (to 4.0) The touch panel sensitivity has now be...