FXC 3009 User Manual

[Page 1] FXC FXC3009

Intelligent 8+2G Switch User's Manual Version 1.0 (Oct. 2004) ...

[Page 2] FXC FXC3009

2 We make no warranties with respect to this documentation and disclaim any implied warranties of merchantability, quality, or fitness for any particular purpose. The information in this document is subject to change without notice. We rese...

[Page 3] FXC FXC3009

Contents 1. INTRODUCTION..........................................................................................1 1.1 PACKAGE CONTENTS...................................................................................1 2. WHERE TO PLACE THE...

[Page 4] FXC FXC3009

1 1. Introduction This switch is a cost-effect high performance 8TX + 2Gigabit ports 10/100/1000 Mbps Ethernet/Fast Ethernet/Gigabit Ethernet management switch with Broadcom solution. There are two built-in gigabit ports for high-speed use...

[Page 5] FXC FXC3009

2 ...

[Page 6] FXC FXC3009

3 2. Where To Place the Intelligent Switch This Intelligent Switch can be placed on a flat surface (your desk, shelf or table). Place the Intelligent Switch at a location with these connection considerations in mind: z The switch configu...

[Page 7] FXC FXC3009

4 Straight-Through cable Max. 100m Another Switch 3.3 Connecting with Trunk connection This switch supports trunk function for high-speed connection between switches to remove the bottleneck problem of switch-to-switch connection....

[Page 8] FXC FXC3009

5 Workgroup Power User Workgroup File Server File Server Switch Switch Gigabit Connection ...

[Page 9] FXC FXC3009

6 4. Adding Module 4.1 Adding MiniGBIC(SFP) Module A MiniGBIC module slot for gigabit connection extension is supported at front panel. You can add a MiniGBIC module to the switch and this switch gets another gigabit port. MiniGB...

[Page 10] FXC FXC3009

7 5. LEDs Conditions Definition 5.1 LEDs Defined The LEDs provide useful information about the switch and the status of all individual ports. LED STATUS CONDITION Power ON Switch is receiving power. ON Port has established ...

[Page 11] FXC FXC3009

...

[Page 12] FXC FXC3009

9 6. Manage / Configure the switch 6.1 Introduction the management functions This switch is a L2 management switch. It supports in-band management function from SNMP, Http and Telnet interface. It also supports out-band management funct...

[Page 13] FXC FXC3009

10 it will also cause a 30 seconds delay if any network connection is changed because of the network topology detection operation of the protocol. Because there could be more than one switch in the network, users can configure this function ...

[Page 14] FXC FXC3009

11 enable the port for network access. This function is very useful for network security application to prevent illegal users access network through the switch. This switch supports MD5, TLS and PEAP authentication types. 8. IGMP Snoopin...

[Page 15] FXC FXC3009

12 6.2 Management with Console Connection Please follow the steps to complete the console hardware connection first. 1. Connect from the console port of the switch to COM port of PC with the console cable. 2. Start the terminal prog...

[Page 16] FXC FXC3009

13 With help command, you can find the command list as follow. ------------------------------------------------------------------------------------------------------- >help [Command List] ?.............. Help commands backup......... ...

[Page 17] FXC FXC3009

14 >del arl Del ARL [xx-xx-xx-xx-xx-xx] xx-xx-xx-xx-xx-xx is a assigned static Mac ID in ARL table of the switch. You can remove it from the table with the command. For example, “del arl 00-11- 22-33-44-55” will delete the static...

[Page 18] FXC FXC3009

15 3. Find command The “find” command can find a static Mac address in the ARL table. Enter “find” at the prompt, the command syntax will be shown. >find [Command List] ?.............. Help commands help........... Help comma...

[Page 19] FXC FXC3009

16 Enter “reset” at the prompt, the command syntax will be shown. >reset Syntax: reset [configuration | system] “reset configuration” will restore the configuration to the factory default setting. “reset system” will rese...

[Page 20] FXC FXC3009

17 For example, “set ARL 00-c0-f6-11-22-33 5 low” will add a static Mac ID “00-c0-f6-11-22-33” to ARL table for Port 5 with low priority and this Mac ID will never be aged out from Port 5. Note : Because the static Mac address i...

[Page 21] FXC FXC3009

18 For example, “set igmp routerport 2” will set the IGMP active connection is at Port 2 of the switch. You have to assign the port that connects IGMP active device first for IP multicast operation. 9.7 set mirror command This comma...

[Page 22] FXC FXC3009

19 9.7.4 set mirror enable command This command is used to enable the mirror operation. 9.7.5 set mirror disable command This command is used to disable the mirror operation. 9.8 set age command This command is used changed the aging ...

[Page 23] FXC FXC3009

20 User can configure the following items for each port. a. Name of a port with “name” sub-command. b. Enable/Disable a port with “admin” sub-command. c. Operation speed of a port with “speed” sub-command. d. Duplex mode of a ...

[Page 24] FXC FXC3009

21 This command is used to set the weight of traffic rate for low priority queue. For example, “set qos lq=3” command will set the weight of traffic rate for low priority queue to 3. 9.11.6 set qos pt command This command is used to...

[Page 25] FXC FXC3009

22 function. The trunk groups are disabled and null trunk groups default. Users can use this command to configure trunk function of the switch. Its syntax is . . . >set trunk Syntax : Set trunk enable Description: Enable trunk f...

[Page 26] FXC FXC3009

23 >set mactrunk giga Syntax: Set mactrunk giga [disable | 0 | 1 | 2]! [disable] : Disable Giga port trunking! [0 | 1 | 2]: Specify Giga group id to enable Giga port trunking! 0= Port 9/G1,10/G2 Note: 9/G1 means the Port# is 9 and it i...

[Page 27] FXC FXC3009

24 [Command List] enable......... Set 802.1Q enabled. disable........ Set 802.1Q disabled. membermap...... Set 802.1Q VLAN table membership. tag............ Set 802.1Q VLAN table port tagged/untagged. default_tag.... Set 802.1Q default tag...

[Page 28] FXC FXC3009

25 none: is for “no change”. vid: is for “change VLAN ID”. priority is for “change priority”. vid_priority: is for “vid_priority”. Note : If “vtable” is set to “drop” or “ifilter” is set to “on”, the VLAN ID ...

[Page 29] FXC FXC3009

26 transparent sub-command is used to set the operation of 802.1x function to transparent mode. In this mode, the switch will forward 802.1x packets directly. re_au sub-command is used to enable the re-authentication function of the switc...

[Page 30] FXC FXC3009

27 This command is used to set the Mac address security mode of physical port. If it is enabled and ports are set to “accept”, only the users with the static Mac address on the ports can access network through these ports. Its syntax i...

[Page 31] FXC FXC3009

28 b. set sta enable and set sta disable commands will enable/disable spanning tree function of the switch. c. set sta bridge command is used to configure for the switch. Its syntax is . . . >set sta bridge [Syntax]set sta bridge [a...

[Page 32] FXC FXC3009

29 This command is used to enable/disable the http function of the switch. Because hacker or worm/virus (like ColdRed) often attacks http server, this command is provided to disable http to prevent it. (If this switch is installed in publi...

[Page 33] FXC FXC3009

30 10.5 show cfg command will show model name and Mac address of the switch. For example, >sh cfg [System Configuration] Model Name : Intelligent Switch MAC Address : 00:C0:F6:50:36:6E 10.6 show net command will show IP addre...

[Page 34] FXC FXC3009

31 For applications, you should select Auto Detect mode if the connected device is auto-negotiation enabled. And you can select Auto Negotiation mode if the connected device is auto-negotiation disabled. For most applications, Auto Detect...

[Page 35] FXC FXC3009

32 2 Disabled public 0.0.0.0 3 Disabled public 0.0.0.0 4 Disabled public 0.0.0.0 5 Disabled public 0.0.0.0 The “Status” is the trap operation status of each trap IP address. 1...

[Page 36] FXC FXC3009

33 9 NO 10 NO New Priority Map: old-new old-new old-new old-new 0-0 1-0 2-0 3-0 4-0 5-0 6-0 7-0 Default Tag: Management Port Default tag Pr...

[Page 37] FXC FXC3009

34 Security Key : 12345678 >show dot1x port 802.1X Port Authentication Configuration Menu PORT Status Auth.Mode ================================= 1 - FA 2 - ...

[Page 38] FXC FXC3009

35 ====================================================== 1 128 19 ON None 2 128 19 ON None ...

[Page 39] FXC FXC3009

36 6.3 Management with Http Connection Users can manage the switch with Http Web Browser connection. Before http connection, IP address configuration of the switch should be done first. Please follow the instruction in Section 6.2 ...

[Page 40] FXC FXC3009

37 1. System Configuration “System Configuration” is the homepage of the switch. Users can find firmware version and Mac address of the switch in this page. And users can configure the following items in this page. a. Auto Mo...

[Page 41] FXC FXC3009

38 For Auto Detect mode, the switch will always keep auto-negotiation function ON but just modify its attribution if the auto mode of port is disabled. The Auto-MDIX function will be always enabled in this mode. For applications, you sh...

[Page 42] FXC FXC3009

39 2. Port Configuration You can find link status and port status here. In this page, you can enable/disable port connection function in “Admin.” and configure their operation mode in “Auto”, “Speed/Duplex” and “Flow...

[Page 43] FXC FXC3009

40 3. Spanning Tree In the page, users can enable/disable spanning tree function and configure the bridge parameters. Please refer to 9.20 of Section 6.2 for the details of these parameters. Press [Apply] after any modification. Con...

[Page 44] FXC FXC3009

41 4. Static Address Table This switch supports static Mac address assignment on port. This switch will not age out these static Mac addresses. But there is a limitation for these static Mac addresses - they are allowed to work on...

[Page 45] FXC FXC3009

42 5. Address Table This page will show the Mac addresses learn by the switch. This information is useful for network administrator to check the user connection status. Note : Because of aging time operation of switch, wrong Mac a...

[Page 46] FXC FXC3009

43 6. Mac Security Configuration This function is used to limit the users that can access network through the switch. If this function is enabled and the port is set to Accept mode, only those users with the static Mac addresses can...

[Page 47] FXC FXC3009

44 7. 802.1Q Virtual LAN This web page is for 802.1Q VLAN setting. The operation of 802.1Q VLAN is based on the “tag” in a packet. A tag contains a 12-bit VLAN ID and 3-bit priority information. A packet with tag inside is...

[Page 48] FXC FXC3009

45 The switch can change VLAN ID and Priority setting in a packet. You can select [No Change]/[Change Priority]/[Change VID]/[Change Both] in the Frame Control function. If any modification is requested, the default tag value will be used ...

[Page 49] FXC FXC3009

46 8. 802.1Q Table 802.1Q VLAN Table This function is used to configure the static VLAN setting. Follow the steps to complete a VLAN configuration. 1. Input a VLAN ID in “VID” and click [Select]. 2. Input a VLAN name in “N...

[Page 50] FXC FXC3009

47 9. Port-based Virtual LAN This function is used to configure Port-based VLAN. 1. Select VLAN to “Port-base VLAN” and click [Apply]. 2. Give a name for the VLAN. 3. Mark the ports for the VLAN. 4. Click [Apply] to acti...

[Page 51] FXC FXC3009

48 10. Mirror Follow the steps to configure Mirror function. 1. Enable Mirroring first. 2. Select the capture port. 3. Select the monitored port from Ingress or Egress table – depending on the traffic direction. 4. Select th...

[Page 52] FXC FXC3009

49 11. QoS This switch supports two priority queues on each port for QoS operation. Follow the steps to configure QoS function. 1. Enable QoS first. 2. If port-based priority is used, select ports for High and Low priorities. 3....

[Page 53] FXC FXC3009

50 12. SNMP In this page, you can find and configure the system information. You can also configure GET/SET/Trap Community Name and the IP address for trap operation. Then users can manage this switch with these settings from SNMP ...

[Page 54] FXC FXC3009

51 13. Trunk This switch supports Port-based Trunk and Mac-based Trunk function. For Port-based Trunk, the traffic assignment between trunk cables is based on physical port – e.g. the traffic from Port 5 will go through cable 1 and t...

[Page 55] FXC FXC3009

52 This switch supports 4 trunk groups and they are null by default. If users want to use Mac-based trunk function, follow the steps to configure it. a. Select “Mac-based” first. b. Assign ports to the trunk. Then click [Apply]. ...

[Page 56] FXC FXC3009

53 14. IGMP This switch supports IP multicast function with IGMP snooping operation. Follow the steps to complete the setting. 1. Enable IGMP first. 2. Select “Router Port” – the port connecting to the IGMP active device. ...

[Page 57] FXC FXC3009

54 15. 802.1x Configuration The 802.1x function can limit the port access for authentication users only. It needs a RADIUS server for the authentication process and the switch acts as an authenticator. The function here is for 8...

[Page 58] FXC FXC3009

55 The Max Request Count is the maximum re-try count between the switch and RADIUS server before authentication fail. 4. Supplicant Timeout Period: This is the timeout value between the switch and users (called “supplicant” in 802.1x) ...

[Page 59] FXC FXC3009

56 16. Statistics You can find the traffic statistics here. Select port number to get the counters for different port. You can modify the refresh interval to get different counter updating period. Click “Refresh” button can...

[Page 60] FXC FXC3009

57 17. Tools Four functions are supported as the system maintenance tools. a. System Upgrade This function will upgrade the system operation software from the web management PC. b. System Backup [Backup Setting] will backup th...

[Page 61] FXC FXC3009

58 18. Port Status Picture At upper part of the web interface, there is a picture showing current status of each port – green for link-up, black for link-down and orange for disabled. With this picture, you can get current port st...

[Page 62] FXC FXC3009

59 6.4 About Telnet Interface If you want to use Telnet to management the switch from remote site, you have to set the IP/Mask/Gateway address to the switch first from console. Then use "telnet <IP>" command in DOS. Its o...

[Page 63] FXC FXC3009

60 7. Software Update and Backup This switch supports software/configuration backup and update/restore functions. It could be done in three ways. 1. From console when booting : by Xmodem protocol and doing by terminal program. This ...

[Page 64] FXC FXC3009

61 A. Product Specifications Access Method Ethernet , CSMA/CD Standards Conformance IEEE 802.3 10BASE-T, IEEE 802.3u 100BASE-TX IEEE 802.3ab 1000Base-T, IEEE 802.3z MDI/MDIX Auto-detect for each TX port Indicator Panel LEDs for ea...

[Page 65] FXC FXC3009

62 B. Compliances EMI Certification FCC Class A Certification (USA) Warning: This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause inter...