Clifford GP1000T Owner's Manual

[Page 1] Clifford GP1000T

GP1000T OOwwnneerr’’ss GGuuiiddee ...

[Page 2] Clifford GP1000T

i © 2005 directed electronics, inc. all rights reserved limited lifetime consumer warranty Directed Electronics, Inc. ("Directed") promises to the original purchaser to repair or replace with a comparable reconditioned model any Directed u...

[Page 3] Clifford GP1000T

ii LOSS, LOSS OF ECONOMIC OPPORTUNITY AND THE LIKE. NOTWITHSTANDING THE ABOVE, THE MANUFACTURER DOES OFFER A LIMITED WARRANTY TO REPLACE OR REPAIR THE CON- TROL MODULE AS DESCRIBED ABOVE. Some territories do not allow limitations on how long an impli...

[Page 4] Clifford GP1000T

1 © 2005 directed electronics, inc. all rights reserved limited lifetime consumer . . . . . . . warranty . . . . . . . . . . . . . . . . . . . . .i trademarks and copyrights . . . . .ii table of contents . . . . . . . . . . . . .1 what is include...

[Page 5] Clifford GP1000T

2 what is included z One control module/siren with built-in Tilt sensor z One 24-pin main wiring harness z One Mini-Blue status LED z One 2-button coded Valet switch z One in-key 2-button remote z One 3-button remote z Two Clifford ® G5 decal’s z ...

[Page 6] Clifford GP1000T

3 © 2005 directed electronics, inc. all rights reserved system maintenance The system requires no specific maintenance. The batteries in your remotes will last approximately one year under normal use. Your 3-but- ton remote is powered by a miniature...

[Page 7] Clifford GP1000T

4 remote configurations The GP1000T system has an in-key 2-button remote control and a 3- button remote control. Two additional Clifford ® G5 remote controls can be added. 3-BUTTON REMOTE CONTROL SILENT ARM/DISARM ARM/DISARM/PANIC ACCESSORY FRONT R...

[Page 8] Clifford GP1000T

5 © 2005 directed electronics, inc. all rights reserved remote functions This system uses computer-based code learning to learn the remote buttons. This makes it possible to assign any remote button to any sys- tem function. The remotes initially co...

[Page 9] Clifford GP1000T

6 Button An optional accessory convenience or expansion function that you have added to your system can be activated by pressing this button. Button Silent arm and disarm is controlled by this button. and Buttons When pressed together, these buttons ...

[Page 10] Clifford GP1000T

7 © 2005 directed electronics, inc. all rights reserved While the system is armed, the LED status indicator will flash approxi- mately once per second showing that the system is actively protecting your vehicle. If you hear more than two chirps when...

[Page 11] Clifford GP1000T

8 disarming To disarm the system, press . You will hear a chirp and the indica- tor lights will flash once. If the siren chirps three times when disarming, refer to the Diagnostics section of this guide. This is called Tamper Alert. If the siren is ...

[Page 12] Clifford GP1000T

9 © 2005 directed electronics, inc. all rights reserved 7. Then once. This enters a 0 as there was not a previous digit entered with . 8. Then once. 9. Then once. This enters the final digit 1. 10. Then button once to disarm without a remote. au...

[Page 13] Clifford GP1000T

10 remote to stop the trigger and return the unit to the armed state. The system will not disarm, but rather reset. This prevents you from dis- abling the system should you wish to silence it without visually check- ing the vehicle. After resetting t...

[Page 14] Clifford GP1000T

11 © 2005 directed electronics, inc. all rights reserved remote sensor disable This can be performed anytime the system is armed. Follow the proce- dure listed below. 1. Arm the system. 2. Using the remote press and simultaneously. 3. The indicato...

[Page 15] Clifford GP1000T

12 auxiliary channel bypass All alarm sensor inputs will be bypassed while a pulsed or timed auxil- iary output is active. panic mode If you are threatened near your vehicle, you can attract attention by triggering the system with your remote! Just p...

[Page 16] Clifford GP1000T

13 © 2005 directed electronics, inc. all rights reserved To exit Valet Mode: 1. Turn the ignition On, the system will exit Valet ® mode auto- matically. remote valet mode The operations described in this section refer to remote buttons. Remember, t...

[Page 17] Clifford GP1000T

14 low battery warning When the transmitter battery is low, the siren will generate 5 rapid chirps when the alarm is disarmed. automatic noise abatement Alarm sounding is limited to ten 30-second siren duration cycles to meet European criteria and lo...

[Page 18] Clifford GP1000T

15 © 2005 directed electronics, inc. all rights reserved diagnostics The microprocessor at the heart of your security system is constantly monitoring all of the switches and sensors that are connected to it. It detects any faulty switches and sensor...

[Page 19] Clifford GP1000T

16 The security system will ignore the input that was active when the sys- tem was armed, until the input goes away. 3-seconds later the system will monitor that input normally. For example, if the protective switch is active, you will hear four Bypa...

[Page 20] Clifford GP1000T

17 © 2005 directed electronics, inc. all rights reserved arm/disarm diagnostic chart Refer to the table of zones to identify the last zone triggered. Action No. of Chirps Description Arm 2 System armed Arm 4 System armed with a protection switch ac...

[Page 21] Clifford GP1000T

18 table of zones The zone number is the number of LED flashes used by the system to identify a specific input. The standard input assignments are listed below, along with spaces to write in any optional sensors or switches you have had installed. If...

[Page 22] Clifford GP1000T

19 © 2005 directed electronics, inc. all rights reserved high frequency Your system transmits and receives at 433 MHz. This provides a cleaner spectrum with less interference and a more stable signal. smart power up II This security system will stor...

[Page 23] Clifford GP1000T

20 z After 96 hours of no activity (arm, disarm, or alarm trigger) the alarm enters sleep mode. The alarms receiver, and LED turn off to save as much battery power as possible. The system is drawing next to no current in this mode.  To exit sleep ...

[Page 24] Clifford GP1000T

21 © 2005 directed electronics, inc. all rights reserved Following is a list of the program settings, with the factory settings in bold: z Autoarming on or autoarming off of the alarm : Automatic arming 30-seconds after ignition turned off. z Arming...

[Page 25] Clifford GP1000T

22 manual programming instructions It is a good idea to document changes by taking note of all feature changes made in programming mode. To enter the User Selectable Features programming: 1. Ignition on - Turn the ignition to the on/run position or s...

[Page 26] Clifford GP1000T

23 © 2005 directed electronics, inc. all rights reserved 6. Feature change - Press the button on the remote. If the system chirps once, the feature has just turned off or switched to the first setting in the grid slot for this feature.; if the syst...

[Page 27] Clifford GP1000T

24 user selectable features user selectable features descriptions - column one add new remote (for 2-button in-key and 3-button remotes only) z Auto-learn new remote controls to the system (one at a time) in the standard button configuration. For mor...

[Page 28] Clifford GP1000T

25 © 2005 directed electronics, inc. all rights reserved auto (passive) arm - on/off z On: When the system sees the ignition turn off, it will begin a 30-second countdown before arming itself. The count- down is indicated by the system LED rapid fla...

[Page 29] Clifford GP1000T

26 select siren sounds This feature allows you to select which siren sounds will be played back when the alarm is triggered (default is Tone 1). Use the following pro- cedure to set this feature: 1. Enter the feature. 2. Press the button of the remot...

[Page 30] Clifford GP1000T

27 © 2005 directed electronics, inc. all rights reserved features. To program specific functions to a different button, enter the function you are programming after the chirp confirmation. Press the button with which you wish to control that feature...

[Page 31] Clifford GP1000T

28 sensor disable z The remote button programmed for this feature will make the system bypass the sensors for one arming cycle only. On the next arming cycle, zones 1, 2, and 3 will be reinstated. clear all remotes z This feature will erase all remot...

[Page 32] Clifford GP1000T

29 © 2005 directed electronics, inc. all rights reserved z For the rest of the channels only one press of the button is required to learn, and the siren will chirp the same number of times as the feature row. Note #3: Accessory Channel z The accesso...

[Page 33] Clifford GP1000T

30 pin programming A PIN code can have one to four digits; each digit can be from 0-9. Programming Procedure 1. Enter the feature location (column 2, row 1) in the user- selectable programming grid. 2. Immediately press and release of the Valet swit...

[Page 34] Clifford GP1000T

31 © 2005 directed electronics, inc. all rights reserved PIN Code Confirmation Procedure Begin this procedure within 15 seconds of finishing the programming sequence or the new code will not be set. 1. Turn on the ignition. 2. Enter the new PIN code...

[Page 35] Clifford GP1000T

32 glossary of terms Control Unit: The "brain" of your system hidden somewhere on the motorcycle where it is difficult for a thief to access. It houses the micro- processor which monitors your vehicle and controls all of the system's f...

[Page 36] Clifford GP1000T

33 © 2005 directed electronics, inc. all rights reserved security & convenience expansions Here we have listed only some of the many expansion options avail- able. Please contact your dealer for a complete list of all the options available to yo...

[Page 37] Clifford GP1000T

34 health check Directed Electronics recommends you return to your installing Clifford ® dealer to have your system checked for correct operation. The first check is due one year after the installation date and at yearly intervals thereafter. nnoott...

[Page 38] Clifford GP1000T

www.directed.com © 2005 Directed Electronics, Inc. - All rights reserved G909500 04-05 The company behind this system is Directed Electronics, Inc. E&OE, specification is subject to change without notice. Some vehicles require optional parts/wi...