CDA hn9625 Manual For Installation, Use And Maintenance

[Page 1] CDA hn9625

Customer Care Department • The Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : [email protected] W : www.cda.eu hn9625 Induction Hob Manual for Installation, Use and Main...

[Page 2] CDA hn9625

2 Important The CDA Group Ltd cannot be held responsible for injuries or losses caused by incorrect use or installation of this product. Please note that CDA reserve the right to invalidate the guarantee supplied with this product following incor...

[Page 3] CDA hn9625

3 2004/108/EC. Parts intended to come into contact with food conform to 89/109/EC. IMPORTANT INFORMATION FOR CORRECT DISPOSAL OF THE PRODUCT IN ACCORDANCE WITH EC DIRECTIVE 2002/96/EC. At the end of its working life, the product must be taken to a...

[Page 4] CDA hn9625

4 • Do not place hot lids flat on the hob top. A “suction” eect could cause damage to the hob. • Do not drag cookware across the hob top: in the long term, this could cause damage to the hob. • Do not store cleaning or flammab...

[Page 5] CDA hn9625

5 Important • Do not use the hob if the glass surface is cracked or damaged to prevent the risk of electric shock. Disconnect it from the power supply. • Ensure that the power cable of a connected electrical appliance near the hob is not ...

[Page 6] CDA hn9625

6 Cooking on Induction The principle of induction cooking is based on magnetic eect. When you put your cookware on an induction zone and switch it on, the electronic boards in the hob produce induced currents in the base of the cookware and inst...

[Page 7] CDA hn9625

7 Using Your Hob Power level Type of cooking 0 Switched o 1/2 For melting (butter/chocolate) or keeping food warm 2/3 Keeping food hot or to heat small quantities of liquid 3/4 Heat larger quantities of liquid (sauces etc.) 4/5 Slow boiling, ...

[Page 8] CDA hn9625

8 Using Your Hob To switch the hob on • To switch the power on, touch and hold for approximately two seconds. The hob will beep and all four zone displays will show “0”. Please note: If a power level is not set within twenty seconds, th...

[Page 9] CDA hn9625

9 Booster • The hob is equipped with a booster function on the front left and front right zones, allowing a higher power level than the maximum for approximately five minutes. To turn on the booster function, touch the zone display for the re...

[Page 10] CDA hn9625

10 Timer/Minute Minder The hob is equipped with a timer that allows a finish time to be set for the end of cooking on any zone, between a minimum of one minute and a maximum of 99 minutes. This timer can be used separately for each zone, and an L...

[Page 11] CDA hn9625

11 Please note: the power level can be adjusted during the countdown using the slider control To cancel the timer • Touch the zone display for the required zone, and then the timer display. The timer display will show “0-” and the LED will...

[Page 12] CDA hn9625

12 Safety key lock To prevent accidental use, the hob has a safety key lock which switches o the slider control temporarily or completely. To switch on the lock, turn on the hob, touch the front right zone display and simultaneously, then to...

[Page 13] CDA hn9625

13 Ecient Use of your Hob The hob is equipped with zones of dierent sizes, designed to accommodate most shapes and sizes of pan. For best results, only use pans with flat bottoms and choose an appropriate zone depending on the size of the ...

[Page 14] CDA hn9625

14 Types of residues Clean with Cleaning advice Light Cleaning sponge and soft cloth Wipe over the zone to be cleaned with a sponge and hot water, and then wipe o with a soft dry cloth. Accumulated baked- on stains/dirt, sugar spills or melted...

[Page 15] CDA hn9625

15 If your hob is not working: 1. Check that the zone is switched on. 2. Check that the mains supply has not been switched o. 3. Check that the fuse in the spur has not blown. In the event of a fault with the hob, please advise ...

[Page 16] CDA hn9625

16 You observe that Possible Causes What should you do? The display shows a series of digits and symbols on first connection Working normally Nothing, the hob will be ready to use within approximately 30 seconds Installation blows a fuse or only...

[Page 17] CDA hn9625

17 Should any error code other than those listed above show on the zone displays, contact CDA Customer Care for assistance IMPORTANT - PLEASE NOTE: In the event of any breakage, crack or cracking – even minimal – of the vitroceramic glass, imm...

[Page 18] CDA hn9625

18 Fig.3 Fitting the Hob Unpacking the hob: Take care not to lose or mishandle any parts. Fitting position of the hob: This appliance must be installed a minimum of 50mm from any back wall and a minimum of 180mm away from any adjacent vertical su...

[Page 19] CDA hn9625

19 If tting a cooker hood above the hob: If a cooker hood is to be installed above the hob, the height of the hood above the hob must be at least 600mm (650mm is recommended) (Fig.6). If the instructions supplied with the hood dictate that the...

[Page 20] CDA hn9625

20 Notes: • The hob is equipped with an anti-overheating safety device that can be activated if the hob is installed over an oven that is not suciently ventilated. In the event that this occurs, the control panel will show E2, ER21 or ER40...

[Page 21] CDA hn9625

21 Fig.6 400mm 600mm from the wall to the cut-out edge. The distance from the hob, when fitted, to the back wall is 50mm. If a splashback/worktop upstand is to be fitted, take this into account when cutting the hole. The minimum distance that...

[Page 22] CDA hn9625

22 Mains Electricity Connection Warning! this appliance must be earthed We recommend that the appliance is connected by a qualified electrician, who is a member of the N.I.C.E.I.C. and who will comply with the I.E.T. and local regulations. Thi...

[Page 23] CDA hn9625

23 2.5mm  , HO5RR-F). • This appliance is intended to be connected to the mains supply with a cable of cross section area 2.5mm  . A larger cable will not fit the terminal connections. • The current rating of the fuse or circuit ...

[Page 24] CDA hn9625

Please contact our Customer Care Department for Service on the details below Customer Care Department • The Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : [email protected]...