Dell PowerEdge UPS 500T User's Manual

Download or browse on-line these Operation & User’s Manual for Dell PowerEdge UPS 500T Server.

Dell PowerEdge UPS 500T Manual Information:

This manual for Dell PowerEdge UPS 500T, given in the PDF format, is available for free online viewing and download without logging on. The guide contains 88 pages, and the size of the file at download is 1.55 Mb. The document type is Operation & User’s Manual.

Download Manual

More Manuals:

In case you failed to obtain relevant information in this document, please, look through related operating manuals and user instructions for Dell PowerEdge UPS 500T. Just click one of the links below to go to the selected manual:

Summary of Contents:

[Page 1] Dell PowerEdge UPS 500T

Dellt Network Management Card User's Guide w w w . d e l l . c o m | s u p p o r t . d e l l . c o m ...

[Page 2] Dell PowerEdge UPS 500T

Notes and Warnings NOTE: A NOTE indicates important information that helps you make better use of your software. DANGER: A DANGER indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. WARNING: A WA...

[Page 3] Dell PowerEdge UPS 500T

3 Table of Contents | Table of Contents 1 Introduction 2 Getting Started Unpacking the Card 8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Installation Checklist 9. . . . . . . . . . . . . . . . . . . ...

[Page 4] Dell PowerEdge UPS 500T

4 | Table of Contents UPS Control 37. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . UPS Weekly Schedule Programming 39. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Shut...

[Page 5] Dell PowerEdge UPS 500T

5 Table of Contents | 5 Specifications 6 Operation and Maintenance Serial Cable Pinout 79. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Serial Configuration Menus 79. . . . . . . . . . . . . . . . . ....

[Page 6] Dell PowerEdge UPS 500T

6 | Introduction Introduction The Dellt Network Management Card works with Dell UPS Management Software to monitor, manage, and protect uninterruptible power supplies (UPSs) through standard Web pages, Simple Network Management Protocol (SNMP), and...

[Page 7] Dell PowerEdge UPS 500T

7 Introduction | S Online Help (English only) S Card firmware updated through the network S UPS firmware updated through the network S Fast Ethernet 10/100 MB compatibility with auto-negotiation on the RJ-45 port S Connection to the card with strai...

[Page 8] Dell PowerEdge UPS 500T

8 | Getting Started Getting Started This chapter explains: S Unpacking the card S Checklist items needed for installation S Identifying the card ports and indicators S Card defaults S Installing and connecting the card S Configuring the network wit...

[Page 9] Dell PowerEdge UPS 500T

9 Getting Started | Installation Checklist 1 Verify that all of the following items are available: - Dell Network Management Card package contents - Phillips ® screwdriver - Ethernet cable - Available serial port (RS-232) - HyperTerminal ® (shi...

[Page 10] Dell PowerEdge UPS 500T

10 | Getting Started Card Details 5 1 4 6 2 3 1. Ethernet Port (10/100BaseT) 2. ACT LED (green) 3. 100M LED (orange) 4. Settings Port 5. UPS Data LED (green) 6. RS232 LED (orange) Figure 3. Dell Network Management Card Details Table 1. Indicator De...

[Page 11] Dell PowerEdge UPS 500T

11 Getting Started | Card Defaults Table 2 lists the Dell Network Management Card default parameters. Table 2. Default Parameters Function On Parameter Default Value Possible Values Network IP Address Subnet Mask Gateway Address BOOTP/DHCP Firmware...

[Page 12] Dell PowerEdge UPS 500T

12 | Getting Started Installing the Card The Dell Network Management Card can be installed in any Dell UPS equipped with a communication bay without turning off the UPS or disconnecting the load. To install the Dell Network Management Card: 1 Remov...

[Page 13] Dell PowerEdge UPS 500T

13 Getting Started | 3 Connect an active Ethernet cable (not supplied) to the Ethernet port on the Dell Network Management Card (see Figure 5). Wait approximately two minutes until the UPS Data LED flashes regularly, indicating normal operation. Et...

[Page 14] Dell PowerEdge UPS 500T

14 | Getting Started Configuring the Card To configure the card: 1 Verify that the serial cable (supplied) is connected to the card's Settings port and the computer's COM port. 2 Open your terminal emulation program (such as HyperTerminal...

[Page 15] Dell PowerEdge UPS 500T

15 Getting Started | 5 Verify that the UPS is turned on. The initialization process completes, and you are prompted enter the password (Figure 7). ------------------------------------------------------------- End of Init, card is ready ... Enter pa...

[Page 16] Dell PowerEdge UPS 500T

16 | Getting Started Configuring the Network With a DHCP Server The card automatically collects the IP parameters from the server by default. NOTE: When the card is not connected to the network, it continuously attempts to connect. When the connec...

[Page 17] Dell PowerEdge UPS 500T

17 Getting Started | 3 Record the IP address. 4 To exit, type 0 and press Enter; then type 0 and press Enter again. The card is now operational. Configuring the Network Without a DHCP Server To set the network configuration manually: 1 From the mai...

[Page 18] Dell PowerEdge UPS 500T

18 | Getting Started Testing the Configuration To verify that the Dell Network Management Card is operational: 1 Open a Web browser from a station connected to the same subnet as the card. 2 Enter the card's https://IP address (IPv4 or IPv6) i...

[Page 19] Dell PowerEdge UPS 500T

19 Configuring the Card | Configuring the Card NOTE: You must be logged in as admin to configure the card. This chapter explains: S Navigating the card's Web page S Understanding UPS properties S UPS power management S Understanding UPS measur...

[Page 20] Dell PowerEdge UPS 500T

20 | Configuring the Card Navigating the Card's Web Page Figure 13 shows the different areas and features of the card’s Web page. The UPS Properties page is the home page that displays after you log on to the Web interface. Menu Bar Link to ...

[Page 21] Dell PowerEdge UPS 500T

21 Configuring the Card | Logging In By default, the user name and password are both admin (see Figure 14). Figure 14. Login Window Both the user name and password fields accept a maximum of ten characters. After five minutes have elapsed, or if th...

[Page 22] Dell PowerEdge UPS 500T

22 | Configuring the Card Online Help The Dell Network Management Card's online Help provides information on all main menu items. NOTE: The Help is in English only. To access Help: 1 Click Help. The Help page opens(see Figure 15). 2 Select a ...

[Page 23] Dell PowerEdge UPS 500T

23 Configuring the Card | UPS Properties Essential information about the UPS status is available on the UPS Properties page (see Figure 16), which refreshes automatically every ten seconds. The UPS Properties page shows an image and generic name of...

[Page 24] Dell PowerEdge UPS 500T

24 | Configuring the Card UPS Measurements Detail Place the cursor over the diagram to display the UPS measurements detail (see Figure 17). These measurements are available for Normal mode, Battery mode, and Bypass mode. The available measurements ...

[Page 25] Dell PowerEdge UPS 500T

25 Configuring the Card | Diagrams display examples of the UPS current operating mode (see Table 4). NOTE: If communication with the UPS is lost, all diagrams appear gray. Table 4. Operating Mode Diagrams Operating Mode Diagram UPS with Automatic ...

[Page 26] Dell PowerEdge UPS 500T

26 | Configuring the Card Table 5 lists all the elements that can appear in a UPS operating mode diagram. Table 5. Diagram Elements Type Icons Description AC Normal Input Green In tolerance Gray Out of tolerance AC Normal Flow Yellow AC to DC con...

[Page 27] Dell PowerEdge UPS 500T

27 Configuring the Card | Table 5. Diagram Elements (continued) Type DescriptionIcons Battery Output Flow Yellow AC to DC converter powered by battery Gray AC to DC converter not powered by battery DC to AC Converter Input Flow Yellow Energy flow p...

[Page 28] Dell PowerEdge UPS 500T

28 | Configuring the Card Table 5. Diagram Elements (continued) Type DescriptionIcons AC Automatic Bypass Status Green Powered Gray Not powered Red Internal failure AC Output Flow Yellow Energy flow present Gray No energy flow AC Output Green Load ...

[Page 29] Dell PowerEdge UPS 500T

29 Configuring the Card | UPS Status List Select an item from the UPS Status list to view specific information about the UPS (see Figure 18). Table 6 lists the items available. The following sections describe each item in detail. UPS Status List Fi...

[Page 30] Dell PowerEdge UPS 500T

30 | Configuring the Card UPS Status The UPS Status view displays the following basic information about power and output: S Power source: Indicates whether power comes from the utility or from the UPS battery. S Output load level: Indicates the pow...

[Page 31] Dell PowerEdge UPS 500T

31 Configuring the Card | View Current Alarms Select UPS Alarms from the UPS Status list to display the list of current alarms (see Figure 19). Table 8 lists the alarm severity levels. Table 9 and Table 10 list the managed UPS and system alarms. Fi...

[Page 32] Dell PowerEdge UPS 500T

32 | Configuring the Card Table 9. UPS Alarms Alarm On Alarm Off Battery fuse blown Battery fuse OK No Battery Battery present Battery temperature fault Battery temperature OK Battery charger fault Battery charger OK Battery fault Battery OK MAX...

[Page 33] Dell PowerEdge UPS 500T

33 Configuring the Card | Table 9. UPS Alarms (continued) Alarm On Alarm Off Inverter overload Inverter load OK Inverter over temperature Inverter temperature OK Inverter short circuit Inverter OK Inverter thermal overload Inverter load OK Load not...

[Page 34] Dell PowerEdge UPS 500T

34 | Configuring the Card Table 9. UPS Alarms (continued) Alarm On Alarm Off On buck Return from buck On boost Return from boost Table 10. System Alarms Dell Network Management Card startup Send test mail SUCCESS Send test mail ERROR Send mail to ...

[Page 35] Dell PowerEdge UPS 500T

35 Configuring the Card | View Power Consumption Select UPS Metrics from the UPS Status list to display levels of power consumption (see Figure 20) for the following: S Peak Consumption: Indicates the last peak of consumption since the last reset. ...

[Page 36] Dell PowerEdge UPS 500T

36 | Configuring the Card View UPS and Card Information Select About Your UPS from the UPS Status list to display information about the UPS and the card (see Figure 21). Figure 21. About Your UPS Display ...

[Page 37] Dell PowerEdge UPS 500T

37 Configuring the Card | UPS Control Click UPS Control from the menu bar to open the UPS Control page (see Figure 22). Figure 22. UPS Control Page The UPS Control page enables triggering of startup and shutdown sequences for the UPS main output an...

[Page 38] Dell PowerEdge UPS 500T

38 | Configuring the Card S Safe power down & reboot: Immediately launches a sequence to switch off and then restore output power. It shuts down the powered systems during the shutdown sequence, and then switches off the output. Finally, it lau...

[Page 39] Dell PowerEdge UPS 500T

39 Configuring the Card | UPS Weekly Schedule Programming Click Weekly Schedule from the menu bar to set up the timing of specific weekly actions (see Figure 23). Figure 23. Weekly Schedule Page NOTE: UPS configuration can prevent the shutdown and ...

[Page 40] Dell PowerEdge UPS 500T

40 | Configuring the Card Shutdown Parameters Click Shutdown Parameters from the menu bar to view and configure UPS operating parameters in battery mode and for power restoration (see Figure 24). Figure 24. Shutdown Parameters Page (Advanced Parame...

[Page 41] Dell PowerEdge UPS 500T

41 Configuring the Card | UPS Shutdown (Inverter) The first shutdown criterion initiates the restart of the shutdown sequence if the remaining time is under (0 to 99999 seconds, 180 by default). This value is the minimum remaining backup time befor...

[Page 42] Dell PowerEdge UPS 500T

42 | Configuring the Card Measurements Click Measurements from the menu bar to view the measurements for the UPS (see Figure 25). Figure 25. Measurements Page The following measurements are saved and time-stamped: S AC Normal Voltage: Value of the ...

[Page 43] Dell PowerEdge UPS 500T

43 Configuring the Card | The save frequency of these values (60 seconds by default) is defined on the System page (see “System Settings” on page 52). Approximately 435 time-stamps can be stored on the card. When the system exceeds this thresho...

[Page 44] Dell PowerEdge UPS 500T

44 | Configuring the Card The card can save up to 435 events. When this threshold is exceeded, the system deletes the oldest event when a new one occurs. Save Log enables you to save values in CSV format. Clear Log enables you to delete all records...

[Page 45] Dell PowerEdge UPS 500T

45 Configuring the Card | Notification E-Mail Notification The card can redirect UPS alarms to an e-mail server to distribute information to the appropriate recipients. The format of these e-mail messages is compatible with mobile telephone transfe...

[Page 46] Dell PowerEdge UPS 500T

46 | Configuring the Card Each recipient is configured with the following parameters: S Recipient (limited to 99 characters): The e-mail address of the person or department to receive the e-mail. The default value is [email protected]. The fil...

[Page 47] Dell PowerEdge UPS 500T

47 Configuring the Card | E-Mail Message Settings Use the Email Message Settings page to customize the content of e-mail messages initiated by the card (see “Email Notification” on page 45). See Figure 29. Figure 29. Email Message Settings Page...

[Page 48] Dell PowerEdge UPS 500T

48 | Configuring the Card S Message text: Allows a maximum of 255 characters. As shown in Figure 30, the body of the e-mail message contains: - Message text - The date and time of the event, as saved in the log - URL of the card, enabling a direct ...

[Page 49] Dell PowerEdge UPS 500T

49 Configuring the Card | Network Settings Click Network from the menu bar to configure the network parameters of the card and authorize the remote upgrade of the embedded system (see Figure 31). Figure 31. Network Settings Page Configurable networ...

[Page 50] Dell PowerEdge UPS 500T

50 | Configuring the Card S IPv6 Enabled: When selected, Internet Protocol version 6 (IPv6) features are enabled. NOTE: IPv6 is described in the Internet standard RFC 2460. S IPv6 Auto Config Enabled: Select this option to have the following IPv6 ...

[Page 51] Dell PowerEdge UPS 500T

51 Configuring the Card | NOTE: If the hostname is not used, the IP address supplied by the DHCP server must be assigned through Static DHCP Assignment to maintain the connection with the clients installed on the stations to be protected. NOTE: Dur...

[Page 52] Dell PowerEdge UPS 500T

52 | Configuring the Card System Settings Click System from the menu bar to customize the information that displays on the UPS Properties page (see “UPS Properties Page” on page 23). The System Settings page opens (see Figure 32). Figure 32. Sy...

[Page 53] Dell PowerEdge UPS 500T

53 Configuring the Card | S Factory Reset button: Restores the default configuration of all the card's parameters. S Keep TCP/IP parameters: Select this option to maintain the IP address, subnet mask, gateway, and BOOTP/DHCP value. To ensure s...

[Page 54] Dell PowerEdge UPS 500T

54 | Configuring the Card 2 Click either Modify NMS or Add NMS to open a new window where you can modify or enter SNMP trap receiver information (Application Name, Hostname or IP Address, Trap Community, and Severity). See Figure 34. Figure 34. Add...

[Page 55] Dell PowerEdge UPS 500T

55 Configuring the Card | Access Control Click Access Control from the menu bar to configure the different parameters to allow secure access to the card using a browser or SNMP. NOTE: If you are not already logged on, you will be prompted to enter...

[Page 56] Dell PowerEdge UPS 500T

56 | Configuring the Card S Security mode: Manages the various authentication methods for page access. The default method is SSL and full authentication. Security modes options are: - Authentication for configuration: Only the configuration pages a...

[Page 57] Dell PowerEdge UPS 500T

57 Configuring the Card | Date and Time You can set the card's date and time manually or set to synchronize with the NTP server from the Setting time page (see Figure 36). Figure 36. Setting Time Page ...

[Page 58] Dell PowerEdge UPS 500T

58 | Configuring the Card To set the date and time: 1 Click Time from the menu bar to open the Setting time page. 2 To manually set the date and time, select Set manually and enter values in the Date and Time fields, and click Save. Maximum drift i...

[Page 59] Dell PowerEdge UPS 500T

59 MIB Objects | MIB Objects This chapter describes the Management Information Base (MIB) files available with the card. A MIB is an information repository residing on a device in a communication network. Network management software uses a device&a...

[Page 60] Dell PowerEdge UPS 500T

60 | MIB Objects Table 11. IETF UPS MIB Objects (continued) Variable Name and Relative XML Object Path Variable UnitVariable TypeOID upsEstimatedMinutesRemaining UPS.PowerSummary.RunTimeToEmpty 1.2.3 Integer Min upsEstimatedChargeRemaining UPS.Powe...

[Page 61] Dell PowerEdge UPS 500T

61 MIB Objects | Table 11. IETF UPS MIB Objects (continued) Variable Name and Relative XML Object Path Variable UnitVariable TypeOID upsBypassNumLines No Relative XML Object Path 1.5.2 Integer — upsBypassVoltage UPS.PowerConverter.Input[2].Voltag...

[Page 62] Dell PowerEdge UPS 500T

62 | MIB Objects Table 11. IETF UPS MIB Objects (continued) Variable Name and Relative XML Object Path Variable UnitVariable TypeOID upsAlarmUpsOffAsRequested Relative XML Object Path not implementated 1.6.3.12 — — upsAlarmChargerFailed UPS.Bat...

[Page 63] Dell PowerEdge UPS 500T

63 MIB Objects | Table 11. IETF UPS MIB Objects (continued) Variable Name and Relative XML Object Path Variable UnitVariable TypeOID upsConfigInputVoltage UPS.Flow[1].ConfigVoltage 1.9.1 Integer V upsConfigInputFreq UPS.Flow[1].ConfigFrequency 1.9....

[Page 64] Dell PowerEdge UPS 500T

64 | MIB Objects Dell UPS MIB NOTE: Not every UPS model implements all of the Dell UPS MIB objects. For example, the bypass objects are supported only by larger UPSs with a separate bypass feed. The Dell OID is 674. The Dell UPS MIB must start at O...

[Page 65] Dell PowerEdge UPS 500T

65 MIB Objects | Product Status Group The name of the group is “ProductStatus” with a group OID of 110. See Table 13 for OID 110 group variables. Table 13. Product Status Group Variables Variable Name and Description OID Variable Type productSt...

[Page 66] Dell PowerEdge UPS 500T

66 | MIB Objects Product Physical Group The name of the group is “Physical” with a group OID of 120. See Table 14 for OID 120 group variables. Table 14. Product Physical Group Variables Variable Name and Description OID Variable Type Variable...

[Page 67] Dell PowerEdge UPS 500T

67 MIB Objects | Table 14. Product Physical Group Variables (continued) Variable Name and Description Variable Unit Variable Type OID physicalOutputPresentConsumption Derived by averaging the watt second consumption over the past hour. Use an array...

[Page 68] Dell PowerEdge UPS 500T

68 | MIB Objects Table 14. Product Physical Group Variables (continued) Variable Name and Description Variable Unit Variable Type OID physicalBatteryABMStatus Advanced Battery Monitoring status: 1: ABM charging 2: ABM discharging 3: ABM floating 4:...

[Page 69] Dell PowerEdge UPS 500T

69 MIB Objects | Table 14. Product Physical Group Variables (continued) Variable Name and Description Variable Unit Variable Type OID physicalLoadSegment2ShutdownAfterDelay Number of seconds remaining until Load Segment 2 switches off. -1 if no shu...

[Page 70] Dell PowerEdge UPS 500T

70 | MIB Objects Table 15. Product Physical Group Variables (continued) Trap Name, Description, and Relative XML Object Path Trap LevelTrap trapBypassFrequencyOutOfRange Bypass under or over frequency UPS.PowerConverter.Input[2].PresentStatus.Frequ...

[Page 71] Dell PowerEdge UPS 500T

71 MIB Objects | Table 15. Product Physical Group Variables (continued) Trap Name, Description, and Relative XML Object Path Trap LevelTrap trapInputFrequencyOutOfRangeOk Input under or over frequency ok UPS.PowerConverter.Input[1].PresentStatus.Fr...

[Page 72] Dell PowerEdge UPS 500T

72 | MIB Objects Table 15. Product Physical Group Variables (continued) Trap Name, Description, and Relative XML Object Path Trap LevelTrap trapPosDCLinkUnderVoltage Positive DC link under voltage (applies only to double-conversion models) UPS.Powe...

[Page 73] Dell PowerEdge UPS 500T

73 MIB Objects | Table 15. Product Physical Group Variables (continued) Trap Name, Description, and Relative XML Object Path Trap LevelTrap trapChargerOk Charger ok UPS.BatterySystem.Charger.PresentStatus.InternalFailure = 0 38 1 trapEepromFailure ...

[Page 74] Dell PowerEdge UPS 500T

74 | MIB Objects Table 15. Product Physical Group Variables (continued) Trap Name, Description, and Relative XML Object Path Trap LevelTrap trapBatteryOverVoltage Battery DC over voltage UPS.BatterySystem.Battery.PresentStatus.VoltageTooHigh = 1 49...

[Page 75] Dell PowerEdge UPS 500T

75 MIB Objects | Table 15. Product Physical Group Variables (continued) Trap Name, Description, and Relative XML Object Path Trap LevelTrap trapBatteryTestDone (physical BatteryTestStatus) Battery test done Variable: physicalBatteryTestStatusUPS.Ba...

[Page 76] Dell PowerEdge UPS 500T

76 | MIB Objects Table 15. Product Physical Group Variables (continued) Trap Name, Description, and Relative XML Object Path Trap LevelTrap trapDCLinkImbalance DC link imbalance (applies only to double-conversion models) UPS.PowerConverter.Rectifie...

[Page 77] Dell PowerEdge UPS 500T

77 MIB Objects | Table 15. Product Physical Group Variables (continued) Trap Name, Description, and Relative XML Object Path Trap LevelTrap trapRectifierOverloadOk Rectifier current ok UPS.PowerConverter.Rectifier.PresentStatus.OverLoad = 0 88 1 tr...

[Page 78] Dell PowerEdge UPS 500T

78 | Specifications Specifications Table 16. Technical Specifications Network Connection 10/100BaseT RJ−45 network connector UPS Protocol Dell UPS proprietary protocol Network Protocols (not limited to) DHCP DNS HTTP/HTTPS IPv4 and IPv6 NTP SMTP ...

[Page 79] Dell PowerEdge UPS 500T

79 Operation and Maintenance | Operation and Maintenance This chapter explains: S Serial cable pinout S Detailed serial configuration menus S Firmware upgrade instructions Serial Cable Pinout Figure 37 shows the serial cable and pinout. Female DB-9...

[Page 80] Dell PowerEdge UPS 500T

80 | Operation and Maintenance 3 Enter the admin password (not modifiable). The Dell Network Management Card main menu displays (see Figure 38). ------------------------------------------------------------- Dell Network Management Card ------------...

[Page 81] Dell PowerEdge UPS 500T

81 Operation and Maintenance | Option 2: Network Configuration The Network Configuration option displays additional options for network settings (see Figure 40): ------------------------------------------------------------- Network setting --------...

[Page 82] Dell PowerEdge UPS 500T

82 | Operation and Maintenance S Modify Network settings: To modify existing network parameters (see Figure 42). Restart the card to activate the new parameters. In DHCP mode, the card can receive the following parameters according to the DHCP serv...

[Page 83] Dell PowerEdge UPS 500T

83 Operation and Maintenance | S Set Ethernet speed: To change the network speed (see Figure 43). Restart the card to activate the new parameters. Set the Ethernet speed : [1 : Automatic, 2 : 10 MBit] 1 New Ethernet speed : Automatic Wait while the...

[Page 84] Dell PowerEdge UPS 500T

84 | Operation and Maintenance Option 4: Return to Default Configuration Select menu item 4 to restore the parameters to the factory-default configuration (see “Card Defaults” on page 11). Wait for the confirmation message (see Figure 45). Rest...

[Page 85] Dell PowerEdge UPS 500T

85 Operation and Maintenance | Upgrading the Card's Firmware You can update the card’s firmware by downloading the appropriate file. During the upgrade process, the Dell Network Management Card does not monitor the UPS status. To upgrade the...

[Page 86] Dell PowerEdge UPS 500T

86 | Operation and Maintenance 3 Click Browse to go to the firmware location and select the file to be loaded. 4 Click Upload. NOTE: The upload can take up to five minutes. Do not interrupt the operation before the card displays confirmation that ...

[Page 87] Dell PowerEdge UPS 500T

87 Shutdown Criteria and Sequence | Shutdown Criteria and Sequence This chapter explains: S Shutdown criteria managed by the card S The shutdown sequence S Load segments Shutdown Criteria Managed by the Card During an extended power failure, three ...

[Page 88] Dell PowerEdge UPS 500T

88 | Shutdown Criteria and Sequence Shutdown Sequence At the end of the shutdown procedure, when all servers have been shut down, the UPS itself may shut down to avoid unnecessary discharge of its batteries, depending on its configuration. See Figu...