Xerox 4050 Manual

Download or browse on-line these Message Manual for Xerox 4050 Copier, Printer.

Xerox 4050 Manual Information:

This manual for Xerox 4050, given in the PDF format, is available for free online viewing and download without logging on. The guide contains 115 pages, and the size of the file at download is 0.38 Mb. The document type is Message Manual.

Download Manual

More Manuals:

In case you failed to obtain relevant information in this document, please, look through related operating manuals and user instructions for Xerox 4050. Just click one of the links below to go to the selected manual:

Summary of Contents:

[Page 1] Xerox 4050

Xerox DocuPrint IPS Messages Guide Version 7.1 August 2000 721P88950 ...

[Page 2] Xerox 4050

Xerox Corporation Printing Systems Documentation and Education 701 South Aviation Boulevard, ESM1-058 El Segundo, CA 90245 ©1997, 1998, 1999, 2000 by Xerox Corporation. All rights reserved. Copyright protection claimed includes all forms and matters...

[Page 3] Xerox 4050

XEROX DOCUPRINT IPS MESSAGES GUIDE iii Laser safety ! Warning: Adjustments, use of controls, or performance of procedures other than those specified herein may result in hazardous light exposure. The Xerox DocuPrint printers are certified to comply...

[Page 4] Xerox 4050

iv XEROX DOCUPRINT IPS MESSAGES GUIDE Operation safety Your Xerox equipment and supplies have been designed and tested to meet strict safety requirements. They have been approved by safety agencies, and they comply with environmental standards. Pl...

[Page 5] Xerox 4050

XEROX DOCUPRINT IPS MESSAGES GUIDE v Table of Contents Laser safety iii Ozone information iii Operation safety iv Introduction vii About this guide vii Contents vii Conventions viii Related publications ix 1. HCU messages 1-1 2. DocuPrint 96/4635/180...

[Page 6] Xerox 4050

TABLE OF CONTENTS vi XEROX DOCUPRINT IPS MESSAGES GUIDE ...

[Page 7] Xerox 4050

XEROX DOCUPRINT IPS MESSAGES GUIDE vii Introduction The Xerox DocuPrint IPS Messages Guide contains the messages you may encounter while using your Xerox DocuPrint IPS. About this guide This guide is intended to assist you in dealing with the softwa...

[Page 8] Xerox 4050

INTRODUCTION viii XEROX DOCUPRINT IPS MESSAGES GUIDE Conventions The following conventions are used in this guide: “Overview” References to chapters, sections, and appendices appear in quotations marks. Messages Guide Names of documents and docu...

[Page 9] Xerox 4050

INTRODUCTION XEROX DOCUPRINT IPS MESSAGES GUIDE ix Related publications This document is part of the Xerox DocuPrint IPS publication set. Xerox documents Following is a list of all Xerox DocuPrint IPS documents. For a complete list and description o...

[Page 10] Xerox 4050

INTRODUCTION x XEROX DOCUPRINT IPS MESSAGES GUIDE ...

[Page 11] Xerox 4050

XEROX DOCUPRINT IPS MESSAGES GUIDE 1-1 1. 1HCU messages The messages discussed in this chapter are represented by code numbers displayed in the LED panel on the front of the host channel unit (HCU). Note: The information in this chapter applies on...

[Page 12] Xerox 4050

HCU MESSAGES 1-2 XEROX DOCUPRINT IPS MESSAGES GUIDE Code definitions The following tables give the meaning of the LED codes that may appear on the HCU. Table 1-1. Software states (no decimal point) Code Meaning 9 Checking SRAM 8 Loading microcode a...

[Page 13] Xerox 4050

XEROX DOCUPRINT IPS MESSAGES GUIDE 2-1 2. 2DocuPrint 96/4635/180 IPS messages This chapter contains a list, in numerical order by code, of the messages that you may encounter while using your Xerox DocuPrint 96, 4635, or 180 IPS. It also discusses...

[Page 14] Xerox 4050

DOCUPRINT 96/4635/180 IPS MESSAGES 2-2 XEROX DOCUPRINT IPS MESSAGES GUIDE Figure 2-1. Printer control console 1 Language icon 2 Printer icon 3 Fault List icon 4 Tools icon 5 Guarded Tools icon 6 Clear button 7 Continue button 8 Stop button 9 Sample b...

[Page 15] Xerox 4050

DOCUPRINT 96/4635/180 IPS MESSAGES XEROX DOCUPRINT IPS MESSAGES GUIDE 2-3 4. Tools icon Select this icon to display call for service information and to adjust display features of the printer control console (for example, alarm volume). 5. Guarded ...

[Page 16] Xerox 4050

DOCUPRINT 96/4635/180 IPS MESSAGES 2-4 XEROX DOCUPRINT IPS MESSAGES GUIDE Message list Note: Throughout the messages in this section, ‘%s’ denotes a file name that is supplied by the system when the message is displayed. 01-210 Printer left doo...

[Page 17] Xerox 4050

DOCUPRINT 96/4635/180 IPS MESSAGES XEROX DOCUPRINT IPS MESSAGES GUIDE 2-5 03-202 EDN comm problem with the UIM The EDN cannot communicate with the UIM. Action Select the Fault List icon on the printer control console touch screen. Then touch the [Cl...

[Page 18] Xerox 4050

DOCUPRINT 96/4635/180 IPS MESSAGES 2-6 XEROX DOCUPRINT IPS MESSAGES GUIDE 03-223 CP-IOP unable to com with touch screen. The CP-IOP PSB cannot communicate with the Touch Screen board. Action Select the Fault List icon on the printer control console t...

[Page 19] Xerox 4050

DOCUPRINT 96/4635/180 IPS MESSAGES XEROX DOCUPRINT IPS MESSAGES GUIDE 2-7 03-245 PHN DIO 5 is offline. The PHN Core cannot communicate with PHN DIO board 5. Action Select the Fault List icon on the printer control console touch screen. Then touch th...

[Page 20] Xerox 4050

DOCUPRINT 96/4635/180 IPS MESSAGES 2-8 XEROX DOCUPRINT IPS MESSAGES GUIDE 03-255 FSN1 DIO 1B is offline. The FSN Core cannot communicate with FSN DIO DIO board 1B. Action Select the Fault List icon on the printer control console touch screen. Then t...

[Page 21] Xerox 4050

DOCUPRINT 96/4635/180 IPS MESSAGES XEROX DOCUPRINT IPS MESSAGES GUIDE 2-9 03-343 ROS EXPOS$REF turnaround failure. The MIN SLB/RDR board to raster output scanner (ROS) turnaround test failed. Action Select the Fault List icon on the printer control ...

[Page 22] Xerox 4050

DOCUPRINT 96/4635/180 IPS MESSAGES 2-10 XEROX DOCUPRINT IPS MESSAGES GUIDE 03-372 UIM needs softwreset hardwcaused. UIM Core board detected a potential hardware problem that required a software reset. Action Press the [Clear] or [Reset] button locat...

[Page 23] Xerox 4050

DOCUPRINT 96/4635/180 IPS MESSAGES XEROX DOCUPRINT IPS MESSAGES GUIDE 2-11 03-380 UIM boot ROM download failure. The UIM Core Boot ROM download failed. Action No action required. 03-381 EDN download failure. The EDN Core board download failed. Action...

[Page 24] Xerox 4050

DOCUPRINT 96/4635/180 IPS MESSAGES 2-12 XEROX DOCUPRINT IPS MESSAGES GUIDE 03-390 UIM rigid disk fault. A rigid disk failure was detected by the UIM Core board. Action Select the Fault List icon on the printer control console touch screen. Then touc...

[Page 25] Xerox 4050

DOCUPRINT 96/4635/180 IPS MESSAGES XEROX DOCUPRINT IPS MESSAGES GUIDE 2-13 03-404 System comm problem with PHN. The system is unable to communicate with the PHN. Action Select the Fault List icon on the printer control console touch screen. Then tou...

[Page 26] Xerox 4050

DOCUPRINT 96/4635/180 IPS MESSAGES 2-14 XEROX DOCUPRINT IPS MESSAGES GUIDE 03-416 FSN2 can’t talk to any node on bus. The FSN Core board 2 cannot communicate with any board on the local bus. Action Select the Fault List icon on the printer control...

[Page 27] Xerox 4050

DOCUPRINT 96/4635/180 IPS MESSAGES XEROX DOCUPRINT IPS MESSAGES GUIDE 2-15 03-471 EDN problem needs software reset. A potential hardware or software problem detected on the EDN Core board required a software reset. Action Select the Fault List icon ...

[Page 28] Xerox 4050

DOCUPRINT 96/4635/180 IPS MESSAGES 2-16 XEROX DOCUPRINT IPS MESSAGES GUIDE 03-482 EDN unexpected stacker signal. The job manager received an unexpected delivery signal and initiated a cycle down of the printer. Action Select the Fault List icon on t...

[Page 29] Xerox 4050

DOCUPRINT 96/4635/180 IPS MESSAGES XEROX DOCUPRINT IPS MESSAGES GUIDE 2-17 04-210 PHN missing machine clocks. The machine clock sensor Q401 signal is missing at the PHN Core board. Action Clear areas 4, 5, 6, and 7. (Refer to the Xerox DocuPrint 96/...

[Page 30] Xerox 4050

DOCUPRINT 96/4635/180 IPS MESSAGES 2-18 XEROX DOCUPRINT IPS MESSAGES GUIDE 06-253 Extra end of scan signal. The EOS board detected more than one End of Scan signal. Action Select the Fault List icon on the printer control console touch screen. Then ...

[Page 31] Xerox 4050

DOCUPRINT 96/4635/180 IPS MESSAGES XEROX DOCUPRINT IPS MESSAGES GUIDE 2-19 06-356 EOS PWB connector fault. The +5 VDC was not detected at the EOS board. Action Select the Fault List icon on the printer control console touch screen. Then touch the [C...

[Page 32] Xerox 4050

DOCUPRINT 96/4635/180 IPS MESSAGES 2-20 XEROX DOCUPRINT IPS MESSAGES GUIDE 06-366 Polygon motor fault. A polygon motor error occurred. Action Select the Fault List icon on the printer control console touch screen. Then touch the [Clear] button to cl...

[Page 33] Xerox 4050

DOCUPRINT 96/4635/180 IPS MESSAGES XEROX DOCUPRINT IPS MESSAGES GUIDE 2-21 07-224 Tray 2 open in print. Input tray 2 is open while the system is attempting to print. Action Close input tray 2 and press Continue. 07-241-1 Tray 3 slow to feed position....

[Page 34] Xerox 4050

DOCUPRINT 96/4635/180 IPS MESSAGES 2-22 XEROX DOCUPRINT IPS MESSAGES GUIDE 07-250-2 Tray 4 vert trans door open in print. The Feeder/Stacker Vertical Transport Door Interlock switch opened during printing. Action Close the tray 4 Vertical Transport ...

[Page 35] Xerox 4050

DOCUPRINT 96/4635/180 IPS MESSAGES XEROX DOCUPRINT IPS MESSAGES GUIDE 2-23 08-103 T E jam tray 3 at pre reg Q850. The trailing edge of the sheet of paper did not arrive at the preregistration sensor in time, causing a jam. Action Open the inverter d...

[Page 36] Xerox 4050

DOCUPRINT 96/4635/180 IPS MESSAGES 2-24 XEROX DOCUPRINT IPS MESSAGES GUIDE 08-121 L E jam at tray 2 stack force Q822. The leading edge of the sheet of paper did not arrive at the stack relief sensor in time, causing a jam. Action Open tray 2, clear ...

[Page 37] Xerox 4050

DOCUPRINT 96/4635/180 IPS MESSAGES XEROX DOCUPRINT IPS MESSAGES GUIDE 2-25 08-147 L E jam at dup takeaway roll Q842. The leading edge of the sheet of paper did not arrive at the duplex takeaway roll sensor in time, causing a jam. Action Open the top...

[Page 38] Xerox 4050

DOCUPRINT 96/4635/180 IPS MESSAGES 2-26 XEROX DOCUPRINT IPS MESSAGES GUIDE 08-164-1 L E jam at tray 3 turn baff Q853. The leading edge of the sheet of paper did not arrive at the turn baffle sensor in time, causing a jam. Action Open the vertical tr...

[Page 39] Xerox 4050

DOCUPRINT 96/4635/180 IPS MESSAGES XEROX DOCUPRINT IPS MESSAGES GUIDE 2-27 08-166-2 T E jam at tray 4 turn baff Q853. The trailing edge of the sheet of paper did not arrive at the turn baffle sensor in time, causing a jam. Action Open the horizontal...

[Page 40] Xerox 4050

DOCUPRINT 96/4635/180 IPS MESSAGES 2-28 XEROX DOCUPRINT IPS MESSAGES GUIDE 08-169-1 L E jam at tray 3 horz XPORT Q854. The leading edge of the sheet of paper did not arrive at the horizontal transport sensor in time, causing a jam. Action Open the h...

[Page 41] Xerox 4050

DOCUPRINT 96/4635/180 IPS MESSAGES XEROX DOCUPRINT IPS MESSAGES GUIDE 2-29 08-179 L E jam at third party cross module. There is a paper jam in the indicated area. Action Clear the jam from the area using the steps provided by the system and continue...

[Page 42] Xerox 4050

DOCUPRINT 96/4635/180 IPS MESSAGES 2-30 XEROX DOCUPRINT IPS MESSAGES GUIDE 08-182-2 T E jam at tray 4 takeaway rol Q857. The trailing edge of the sheet of paper did not leave the tray 4 feed sensor in time, causing a jam. Action Open the vertical do...

[Page 43] Xerox 4050

DOCUPRINT 96/4635/180 IPS MESSAGES XEROX DOCUPRINT IPS MESSAGES GUIDE 2-31 08-185-2 L E jam at tray 4 vert XPORT Q852. The leading edge of the sheet of paper did not arrive at the vertical transport sensor in time, causing a jam. Action Open the ver...

[Page 44] Xerox 4050

DOCUPRINT 96/4635/180 IPS MESSAGES 2-32 XEROX DOCUPRINT IPS MESSAGES GUIDE 08-188-2 L E jam at tray 4 turn baffle Q853. The leading edge of the sheet of paper did not arrive at the turn baffle sensor in time, causing a jam. Action Open the vertical...

[Page 45] Xerox 4050

DOCUPRINT 96/4635/180 IPS MESSAGES XEROX DOCUPRINT IPS MESSAGES GUIDE 2-33 08-191 Sheet fed from tray 1 too narrow. The registration transport sensor dynamic width measurement of a sheet of paper fed from tray 1 is less than the expected paper width...

[Page 46] Xerox 4050

DOCUPRINT 96/4635/180 IPS MESSAGES 2-34 XEROX DOCUPRINT IPS MESSAGES GUIDE 08-196-2 Sheet fed from tray 4 is too wide. The registration transport sensor dynamic width measurement of a sheet of paper fed from tray 4 is greater than the expected paper...

[Page 47] Xerox 4050

DOCUPRINT 96/4635/180 IPS MESSAGES XEROX DOCUPRINT IPS MESSAGES GUIDE 2-35 08-204 L E early to regist sensor Q861. The leading edge of the sheet of paper arrived at the registration transport sensor early and could not be registered correctly, causi...

[Page 48] Xerox 4050

DOCUPRINT 96/4635/180 IPS MESSAGES 2-36 XEROX DOCUPRINT IPS MESSAGES GUIDE 08-217-1 Tray 3 feed time below min. The feed time for tray 3 decreased by more than 88ms below the nominal feed time in Standard mode. This error is logged by the system. A...

[Page 49] Xerox 4050

DOCUPRINT 96/4635/180 IPS MESSAGES XEROX DOCUPRINT IPS MESSAGES GUIDE 2-37 08-227 14” transfer assist blade failure. A change in the state of the transfer assist blade sensor was not detected. This error is logged by the system. Action No action i...

[Page 50] Xerox 4050

DOCUPRINT 96/4635/180 IPS MESSAGES 2-38 XEROX DOCUPRINT IPS MESSAGES GUIDE 08-904-1 Tray 3 stock does not match UI. The paper stock loaded in input tray 3 does not match the default paper stock specified for paper tray 3. Action Replace the paper in...

[Page 51] Xerox 4050

DOCUPRINT 96/4635/180 IPS MESSAGES XEROX DOCUPRINT IPS MESSAGES GUIDE 2-39 09-202 AC voltage out of range. The Coronode AC voltage is at or outside of the acceptable limits during printing. This error is logged by the system. Action No action is req...

[Page 52] Xerox 4050

DOCUPRINT 96/4635/180 IPS MESSAGES 2-40 XEROX DOCUPRINT IPS MESSAGES GUIDE 09-222 Too short of time between belt holes. The belt hole sensor made six unsuccessful attempts to detect belt holes within the required spacing. Action Open the doors of th...

[Page 53] Xerox 4050

DOCUPRINT 96/4635/180 IPS MESSAGES XEROX DOCUPRINT IPS MESSAGES GUIDE 2-41 09-326 Transfer current out of range. The monitor voltage for the Trans Shield is less than the control voltage. Action Press the [Reset] button located behind the printer co...

[Page 54] Xerox 4050

DOCUPRINT 96/4635/180 IPS MESSAGES 2-42 XEROX DOCUPRINT IPS MESSAGES GUIDE 09-353 Fail to converge charge in DC951. The contrast potentials did not converge during DC951 setup. Action Press the [Reset] button located behind the printer control consol...

[Page 55] Xerox 4050

DOCUPRINT 96/4635/180 IPS MESSAGES XEROX DOCUPRINT IPS MESSAGES GUIDE 2-43 10-104 L E late to decurler sensor Q1011. The sheet of paper did not arrive at the decurler sensor in time, causing a jam. Action Open the printer right front door, clear are...

[Page 56] Xerox 4050

DOCUPRINT 96/4635/180 IPS MESSAGES 2-44 XEROX DOCUPRINT IPS MESSAGES GUIDE 10-110 T E late at top XPORT sensor Q1012. The trailing edge of the sheet of paper did not leave the top transport sensor in time. Action Open the top cover of the printer, c...

[Page 57] Xerox 4050

DOCUPRINT 96/4635/180 IPS MESSAGES XEROX DOCUPRINT IPS MESSAGES GUIDE 2-45 10-205 Machine over voltage. The voltage to the fuser is greater than 256 VAC. Action Contact your service representative. 10-206 Fuser transient undertemp. The temperature of...

[Page 58] Xerox 4050

DOCUPRINT 96/4635/180 IPS MESSAGES 2-46 XEROX DOCUPRINT IPS MESSAGES GUIDE 10-215 Fuser brake failed while camming out. The camming motor did not stop during printing. Action Press the [Reset] button located behind the printer control console front ...

[Page 59] Xerox 4050

DOCUPRINT 96/4635/180 IPS MESSAGES XEROX DOCUPRINT IPS MESSAGES GUIDE 2-47 11-104 T E jam at inverter entrance Q1155. The trailing edge of the sheet of paper did not arrive at the inverter entrance sensor in time, causing a jam. Action Open the top...

[Page 60] Xerox 4050

DOCUPRINT 96/4635/180 IPS MESSAGES 2-48 XEROX DOCUPRINT IPS MESSAGES GUIDE 11-112 L E jam at prestacker Q1158. The leading edge of the sheet of paper did not arrive at the prestacker sensor in time, causing a jam. Action Open the top cover of stacke...

[Page 61] Xerox 4050

DOCUPRINT 96/4635/180 IPS MESSAGES XEROX DOCUPRINT IPS MESSAGES GUIDE 2-49 11-120 Stray sheet at sample tray Q1157. An extra page was discarded to the sample tray. Action Open the front door of the inverter and clear area 15. Remove and discard the ...

[Page 62] Xerox 4050

DOCUPRINT 96/4635/180 IPS MESSAGES 2-50 XEROX DOCUPRINT IPS MESSAGES GUIDE 11-132-1 L E late to disksheet Q1106A. The leading edge of the sheet of paper did not arrive at the disk sheet sensor in time, causing a jam. Action Open the front door of th...

[Page 63] Xerox 4050

DOCUPRINT 96/4635/180 IPS MESSAGES XEROX DOCUPRINT IPS MESSAGES GUIDE 2-51 11-138-2 L E jam at bypass XPORT Q1107B. The leading edge of the sheet of paper did not arrive at the bypass transport sensor in time, causing a jam. Action Open the top cove...

[Page 64] Xerox 4050

DOCUPRINT 96/4635/180 IPS MESSAGES 2-52 XEROX DOCUPRINT IPS MESSAGES GUIDE 11-141-2 T E late to bypass XPORT Q1107B. The trailing edge of the sheet of paper did not arrive at the bypass transport sensor in time. Action Open the cover above stacker A...

[Page 65] Xerox 4050

DOCUPRINT 96/4635/180 IPS MESSAGES XEROX DOCUPRINT IPS MESSAGES GUIDE 2-53 11-146-1 L E jam at disk (LE) sensor Q1166A. The leading edge of the sheet of paper did not arrive at the disk lead edge sensor in time, causing a jam. Action Open the cover ...

[Page 66] Xerox 4050

DOCUPRINT 96/4635/180 IPS MESSAGES 2-54 XEROX DOCUPRINT IPS MESSAGES GUIDE 11-148-2 T E late to disk (LE) sensor Q1166B. The trailing edge of the sheet of paper did not arrive at the disk edge sensor in time, causing a jam. Action Open the cover ab...

[Page 67] Xerox 4050

DOCUPRINT 96/4635/180 IPS MESSAGES XEROX DOCUPRINT IPS MESSAGES GUIDE 2-55 11-220-1 Stacker A ELV failed to leave home. The elevator did not move from the original position. Action Open the front doors of stacker A, check for any problems, close the ...

[Page 68] Xerox 4050

DOCUPRINT 96/4635/180 IPS MESSAGES 2-56 XEROX DOCUPRINT IPS MESSAGES GUIDE 11-224-2 Stacker B top cover interlock open. The top cover of stacker B is open while the system is attempting to print. Action Open the printer top cover and clear area 8. O...

[Page 69] Xerox 4050

DOCUPRINT 96/4635/180 IPS MESSAGES XEROX DOCUPRINT IPS MESSAGES GUIDE 2-57 11-232-1 Stacker A R guide failed to exit home. The right guide home sensor did not move from the original position. Action Open the top cover above stacker A, clear area 18, ...

[Page 70] Xerox 4050

DOCUPRINT 96/4635/180 IPS MESSAGES 2-58 XEROX DOCUPRINT IPS MESSAGES GUIDE 11-238-2 Stacker B B guide failed to find home. The back guide home sensor did not return to the original position. Action Open the top cover above stacker B and clear area 18...

[Page 71] Xerox 4050

DOCUPRINT 96/4635/180 IPS MESSAGES XEROX DOCUPRINT IPS MESSAGES GUIDE 2-59 11-250-2 Stacker B missing 24VDC. A loss of +24 VDC was detected in the feeder/stacker module. Action Contact your service representative. 11-270-2 Stray sheet at purge sensor...

[Page 72] Xerox 4050

DOCUPRINT 96/4635/180 IPS MESSAGES 2-60 XEROX DOCUPRINT IPS MESSAGES GUIDE 13-205 Third party finisher fault during print. An error occurred with the third party finisher attached to the system. Action Check the bypass transport for jams and retry th...

[Page 73] Xerox 4050

XEROX DOCUPRINT IPS MESSAGES GUIDE 3-1 3. 3DocuPrint 4050, 4090, 4850, 4890, and 92C IPS messages This chapter contains a list, in alphabetical order by code, of the messages that you may encounter while using your Xerox DocuPrint 4050, 4090, 4850...

[Page 74] Xerox 4050

DOCUPRINT 4050, 4090, 4850, 4890, AND 92C IPS MESSAGES 3-2 XEROX DOCUPRINT IPS MESSAGES GUIDE C074 Tray 3 has low paper. Input tray 3 is almost out of paper. Action Add paper to input tray 3. Close paper tray 3 and press the [Continue] button. (Refe...

[Page 75] Xerox 4050

DOCUPRINT 4050, 4090, 4850, 4890, AND 92C IPS MESSAGES XEROX DOCUPRINT IPS MESSAGES GUIDE 3-3 C081 Tray 4 has low paper. Input tray 4 is almost out of paper. Action Add paper to input tray 4. Close paper tray 4 and press the [Continue] button. C082 ...

[Page 76] Xerox 4050

DOCUPRINT 4050, 4090, 4850, 4890, AND 92C IPS MESSAGES 3-4 XEROX DOCUPRINT IPS MESSAGES GUIDE C108 Tray 1 feeder failed to feed sheet from stack to SFRS. The feeder did not move a sheet from the stack to the stack force relief sensor in time. Action...

[Page 77] Xerox 4050

DOCUPRINT 4050, 4090, 4850, 4890, AND 92C IPS MESSAGES XEROX DOCUPRINT IPS MESSAGES GUIDE 3-5 C150 Tray 1 down due to unlock button being pressed. The Unlock button was pressed and input tray 1 is lowered. Action Add paper to tray 1, if necessary. Cl...

[Page 78] Xerox 4050

DOCUPRINT 4050, 4090, 4850, 4890, AND 92C IPS MESSAGES 3-6 XEROX DOCUPRINT IPS MESSAGES GUIDE E092 Vertical transport trailing edge jam. The paper from an input tray did not leave the vertical transport switch in time. Action Clear the jam from area...

[Page 79] Xerox 4050

DOCUPRINT 4050, 4090, 4850, 4890, AND 92C IPS MESSAGES XEROX DOCUPRINT IPS MESSAGES GUIDE 3-7 E099 Late arrival at post fuser switch. The paper did not arrive at the post fuser switch in time. A jam has occurred. Action Clear the jam from area 4. Ma...

[Page 80] Xerox 4050

DOCUPRINT 4050, 4090, 4850, 4890, AND 92C IPS MESSAGES 3-8 XEROX DOCUPRINT IPS MESSAGES GUIDE E117 Late arrival at output tray switch. The paper did not arrive at the output tray switch in time. A jam has occurred. Action Clear the jam from areas 4 ...

[Page 81] Xerox 4050

DOCUPRINT 4050, 4090, 4850, 4890, AND 92C IPS MESSAGES XEROX DOCUPRINT IPS MESSAGES GUIDE 3-9 E131 Low toner in the system. The black dry ink supply is low. Action Add black dry ink and retry the operation. (Refer to the Xerox DocuPrint 4850/4890 or...

[Page 82] Xerox 4050

DOCUPRINT 4050, 4090, 4850, 4890, AND 92C IPS MESSAGES 3-10 XEROX DOCUPRINT IPS MESSAGES GUIDE E226 Bottom transport leading edge jam. The paper fed from the HCF did not arrive at the bottom transport switch in time, causing a jam. Action Clear the ...

[Page 83] Xerox 4050

DOCUPRINT 4050, 4090, 4850, 4890, AND 92C IPS MESSAGES XEROX DOCUPRINT IPS MESSAGES GUIDE 3-11 E248 Transfer blade paper size fault. The paper size that was selected for the job, or that is available in the paper tray, is incorrect. Action Install o...

[Page 84] Xerox 4050

DOCUPRINT 4050, 4090, 4850, 4890, AND 92C IPS MESSAGES 3-12 XEROX DOCUPRINT IPS MESSAGES GUIDE E308 Toner waste container not present. The dry ink waste container is not installed. Action Correctly install a dry ink waste container. (Refer to the Xer...

[Page 85] Xerox 4050

DOCUPRINT 4050, 4090, 4850, 4890, AND 92C IPS MESSAGES XEROX DOCUPRINT IPS MESSAGES GUIDE 3-13 F007 PHR lost machine clock. There is a CPM or PHR board failure or a machine clock signal problem between the CPM and PHR. Action Obtain and discard any ...

[Page 86] Xerox 4050

DOCUPRINT 4050, 4090, 4850, 4890, AND 92C IPS MESSAGES 3-14 XEROX DOCUPRINT IPS MESSAGES GUIDE F040 HCFR lost pitch reset. There is a CPM, MIR, or HCFR board failure or a harness problem between the CPM and MIR or the PHR and HFCR. Action Obtain and...

[Page 87] Xerox 4050

DOCUPRINT 4050, 4090, 4850, 4890, AND 92C IPS MESSAGES XEROX DOCUPRINT IPS MESSAGES GUIDE 3-15 F064 Toner roll bias voltage out of range. There is a printer process control error. Action Press the [Continue] button. If the error persists, contact you...

[Page 88] Xerox 4050

DOCUPRINT 4050, 4090, 4850, 4890, AND 92C IPS MESSAGES 3-16 XEROX DOCUPRINT IPS MESSAGES GUIDE F089 Purged prints in Sample tray and Sample tray was the selected output. The sample tray was specified for the job but contains purged sheets that migh...

[Page 89] Xerox 4050

DOCUPRINT 4050, 4090, 4850, 4890, AND 92C IPS MESSAGES XEROX DOCUPRINT IPS MESSAGES GUIDE 3-17 F137 Excess belt holes detected. The machine has detected too many holes on the photoreceptor belt. Action If trained to do so, replace the photoreceptor b...

[Page 90] Xerox 4050

DOCUPRINT 4050, 4090, 4850, 4890, AND 92C IPS MESSAGES 3-18 XEROX DOCUPRINT IPS MESSAGES GUIDE F158 Stacker jam, late departure from stacker entry sensor or Dynamic Stray Check fault. The paper did not leave the stacker entry in time, causing a jam....

[Page 91] Xerox 4050

DOCUPRINT 4050, 4090, 4850, 4890, AND 92C IPS MESSAGES XEROX DOCUPRINT IPS MESSAGES GUIDE 3-19 F164 Stacker jam, late departure from bin 2 sensor. The paper did not leave bin 2 in time, causing a jam. Action Follow the instructions that display to lo...

[Page 92] Xerox 4050

DOCUPRINT 4050, 4090, 4850, 4890, AND 92C IPS MESSAGES 3-20 XEROX DOCUPRINT IPS MESSAGES GUIDE F175 Stacker jam, late arrival at sensor. The paper did not arrive at the stacker in time, causing a jam. Action Clear the stacker tray. Open and close the...

[Page 93] Xerox 4050

DOCUPRINT 4050, 4090, 4850, 4890, AND 92C IPS MESSAGES XEROX DOCUPRINT IPS MESSAGES GUIDE 3-21 F229 Finishing device full. The output bin of your third-party finishing device is full. Action Remove the jobs contained in the device output bin and pres...

[Page 94] Xerox 4050

DOCUPRINT 4050, 4090, 4850, 4890, AND 92C IPS MESSAGES 3-22 XEROX DOCUPRINT IPS MESSAGES GUIDE F239 Bypass Transport to Finishing device docking fault. Indicates a jam. Action Press the [Continue] button. If the error persists, contact your service ...

[Page 95] Xerox 4050

DOCUPRINT 4050, 4090, 4850, 4890, AND 92C IPS MESSAGES XEROX DOCUPRINT IPS MESSAGES GUIDE 3-23 F271 Chopped color DC bias voltage failure. Indicates that the chopped color DC bias voltage is out of range. Action Press the [Continue] button. If the er...

[Page 96] Xerox 4050

DOCUPRINT 4050, 4090, 4850, 4890, AND 92C IPS MESSAGES 3-24 XEROX DOCUPRINT IPS MESSAGES GUIDE H014 Shared line failure. The CPM cannot communicate with any of the system boards and the PHR cannot communicate with the MIR. In general, this indicates...

[Page 97] Xerox 4050

DOCUPRINT 4050, 4090, 4850, 4890, AND 92C IPS MESSAGES XEROX DOCUPRINT IPS MESSAGES GUIDE 3-25 H032 Fuser under temperature fault. The temperature of the fuser has fallen at least 35 degrees below the required parameters. Action Press the [Continue]...

[Page 98] Xerox 4050

DOCUPRINT 4050, 4090, 4850, 4890, AND 92C IPS MESSAGES 3-26 XEROX DOCUPRINT IPS MESSAGES GUIDE H132 No process control convergence after power up. The charge current is no longer within the system tolerance level. Action Press the [Continue] button. ...

[Page 99] Xerox 4050

DOCUPRINT 4050, 4090, 4850, 4890, AND 92C IPS MESSAGES XEROX DOCUPRINT IPS MESSAGES GUIDE 3-27 H312 Color developer housing fault. An error occurred in the color developer housing. Highlight color printing is not available. Action Verify that the co...

[Page 100] Xerox 4050

DOCUPRINT 4050, 4090, 4850, 4890, AND 92C IPS MESSAGES 3-28 XEROX DOCUPRINT IPS MESSAGES GUIDE H333 Failure of control patch generator. A patch generator error occurred. Action Press the [Continue] button. If the error persists, contact your service ...