Epson SureColor SC-S70600 User's Manual

[Page 1] Epson SureColor SC-S70600

User's Guide NPD4674-00 EN ...

[Page 2] Epson SureColor SC-S70600

Copyrights and Trademarks No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of ...

[Page 3] Epson SureColor SC-S70600

Contents Copyrights and Trademarks Introduction Important Safety Instructions................. 5 When choosing a place for this product. . . . . . . . 5 When setting up this product............... 5 When using this product................... 5 When h...

[Page 4] Epson SureColor SC-S70600

Details of the Menu....................... 100 The Media Setup Menu.................. 100 Printer Setup Menu..................... 104 The Maintenance Menu.................. 106 The Ink Level Menu.................... 108 The Print Logs Menu..............

[Page 5] Epson SureColor SC-S70600

Introduction Important Safety Instructions Read all of these instructions before using the printer. Also be sure to follow all warnings and instructions marked on the printer. When choosing a place for this product ❏ Place this product on a flat, ...

[Page 6] Epson SureColor SC-S70600

❏ This device has two power systems. There is a risk of electric shock unless the two power cables are unplugged during the maintenance. When handling the ink cartridges ❏ Keep ink cartridges out of the reach of children and do not drink. ❏ Do...

[Page 7] Epson SureColor SC-S70600

Printer Parts Front section (SC-S70600 series, SC-S50600 series) The illustration shows the SC-S50600 series. A Maintenance cover (left) Open this cover to clean the area around the print head. Normally closed when using the printer. U “Cleaning Ar...

[Page 8] Epson SureColor SC-S70600

E Tensioner The tensioner maintains tension to prevent the media sagging as it is taken up. F Roll core holder locking screw The locking screws keep the roll core holders in place once they have been attached to the roll core. There are two lift leve...

[Page 9] Epson SureColor SC-S70600

On : An error occurred. Check the contents of the error on the control panel's screen. Off : No error. S AC inlet #1/AC inlet #2 Connects the power cable. Be sure to connect both cables. T LAN port U “LAN port” on page 17 U USB port Connects...

[Page 10] Epson SureColor SC-S70600

Front section (SC-S30600 series) A Maintenance cover (left) Open this cover to clean the area around the print head. Normally closed when using the printer. U “Cleaning Around the Print Head” on page 81 B After heater The heater can be used to ra...

[Page 11] Epson SureColor SC-S70600

G Auto switch Use this switch to select the auto take-up direction.Off Choose Off to disable auto take-up. H Manual switch Use this switch to select the manual take-up direction.Auto The selected option takes effect when the Auto switch is in the Off...

[Page 12] Epson SureColor SC-S70600

U Maintenance cover (right) Open this cover when performing regular maintenance. Normally closed when using the printer. U “Regular Maintenance” on page 79 V Media loading lever After loading media, lower the media loading lever to keep the media...

[Page 13] Epson SureColor SC-S70600

Inside (SC-S70600 series, SC-S50600 series) Dirt on any of the following parts may reduce print quality. Regularly clean or exchange these parts as described in the chapters listed in the reference sections below. The illustration shows the SC-S70600...

[Page 14] Epson SureColor SC-S70600

F Platen heater The platen heater ensures that the ink adheres evenly. U “Heating & Drying” on page 64 U “Cleaning the Platen Heater, Pressure Rollers, and Media Holding Plates” on page 74 G Wiper cleaner The wiper cleaner removes ink fro...

[Page 15] Epson SureColor SC-S70600

Inside (SC-S30600 series) Dirt on any of the following parts may reduce print quality. Regularly clean or exchange these parts as described in the chapters listed in the reference sections below. A Print head The print head prints by moving left and ...

[Page 16] Epson SureColor SC-S70600

F Wiper cleaner The wiper cleaner removes ink from the wiper. It is a consumable; replace about once every six months. U “Replacing the Wiper and Wiper Cleaner” on page 86 G Caps Except during printing, these caps cover the print head nozzles to ...

[Page 17] Epson SureColor SC-S70600

C Roll holder fixing screw These screws fix the roll holders in place once the media has been installed. There are two lift levers: one on the left and one on the right. D Lift lever If the media to be mounted on the roll holders seems heavy, use the...

[Page 18] Epson SureColor SC-S70600

Data lamp Status lamp (green/red) Status On On (green) The printer is connected using a 1000base-T connection. Flashing The printer is receiving data over a 1000base-T connection. On On (red) The printer is connected using a 100base-TX connection. Fl...

[Page 19] Epson SureColor SC-S70600

Control panel A P button (power button) Turns the power on and off. B P light (power light) The printer's operational status is indicated by a lit or flashing light. On : The power is on. Flashing : The printer is receiving data or performing he...

[Page 20] Epson SureColor SC-S70600

Pressing this button displays the Heating & Drying menu, where you can adjust the Heater Temperature. If the additional print drying system (supplied with the SC-S50600 series; optional with other models) is attached, you can also adjust Addition...

[Page 21] Epson SureColor SC-S70600

❏ The media remaining is not displayed if Off is selected for Remaining Setup in the Media Remaining menu. U “The Media Setup Menu” on page 100 D Ink cartridge status Displays the approximate level of remaining ink and the current status. When ...

[Page 22] Epson SureColor SC-S70600

1 Status indicators The status of the waste ink bottle is shown as fol- lows. : No error. The indicator changes to show the amount of space available. : The waste ink bottle is almost full. Ready a new waste ink bottle. : The waste ink bottle is full...

[Page 23] Epson SureColor SC-S70600

Additional Print Drying System Available The additional print drying system (supplied with the SC-S50600 series; optional with other models) can be used for increased drying performance and improved productivity. It is recommended when using the SC-S...

[Page 24] Epson SureColor SC-S70600

Notes on Usage and Storage Installation space Make sure that you secure the following space, clear of any other objects, so that paper ejection and consumable replacement are not obstructed. See the "Specifications Table" for the external d...

[Page 25] Epson SureColor SC-S70600

❏ The print head is automatically cleaned at a fixed interval after printing to keep the nozzle from clogging. Be sure that the waste ink bottle is placed whenever the printer is on. Periodical Cleaning U “Printer Setup Menu” on page 104 ❏ As...

[Page 26] Epson SureColor SC-S70600

❏ Extra ink is required to fully charge the print head nozzles the first time the printer is used; replacement cartridges will be needed earlier than usual. Store ink cartridges at room temperature in a location that is not exposed to direct sunlig...

[Page 27] Epson SureColor SC-S70600

Handling Media Note the following when handling or storing media. Media that are in poor condition will not produce good quality prints. Be sure to read the documentation provided with each type of media. Notes on Handling ❏ Do not fold the media o...

[Page 28] Epson SureColor SC-S70600

Specialty Inks The term “specialty inks” is used for white and metallic silver inks. White and metallic silver inks are prone to precipitation (components settling to the bottom of the liquid). Using the ink in this state can cause a decline in p...

[Page 29] Epson SureColor SC-S70600

Using the Supplied Software Contents of the Software Disc The following applications are available on the supplied software disk. Install as required. For information about these applications, see the Network Guide (pdf) or the on-line help for the a...

[Page 30] Epson SureColor SC-S70600

Starting EPSON LFP Remote Panel 2 Launch EPSON LFP Remote Panel 2 after confirming that the printer displays Ready. Windows A The application can be launched using either of the following two methods. ❏ Double-click the EPSON LFP Remote Panel 2 ic...

[Page 31] Epson SureColor SC-S70600

E Follow the on-screen instructions to continue. When the delete confirmation message appears, click Yes. If you are reinstalling the Epson communications driver, restart the computer. Mac OS X The following describes how to remove the EPSON LFP Remo...

[Page 32] Epson SureColor SC-S70600

Basic Operations Loading and Exchanging Media The process for loading media varies with the model of printer or type of media feeding unit used. Choose the method suited to your particular setup. ! Caution: ❏ The heaters and media holding plate may...

[Page 33] Epson SureColor SC-S70600

c Important: If the right holder handle shaft is not visible, rotate the holder forward until it stops. The media can not be properly loaded if the handle shaft is not visible. C Temporarily place media on the roll supports oriented according to how ...

[Page 34] Epson SureColor SC-S70600

F Tighten the roll holder screw to fix the roll holder in place. G Raise the lift lever on the right side of the printer to lift the media into position, then firmly insert the roll holder. If the roll of media has the outer diameter which is less th...

[Page 35] Epson SureColor SC-S70600

J Raise the media loading lever. K Pull out the media and insert it into the printer. Note: Media that is heavy and difficult to unroll can be fed by pressing the drive switch on the left roll holder. Printable Side Out Printable Side In L Insert t...

[Page 36] Epson SureColor SC-S70600

P Adjust the position of the pressure rollers. The low pressure rollers are used for normal printing, the high pressure rollers for ink layering. Their positions vary with the width of the media and the rollers used. Position the low pressure rollers...

[Page 37] Epson SureColor SC-S70600

S Attach the media holding plates at either side of the media. First, position the plates so that the edges of the media are in the centers of the round holes. Next, adjust the position until the white line is visible in the square window and push th...

[Page 38] Epson SureColor SC-S70600

! Caution: Because the media is heavy, it should not be carried by one person. When loading or removing the media, use at least two persons. Using a lifter is recommended when handling a media that is 40 kg or heavier. A Turn on the printer by pressi...

[Page 39] Epson SureColor SC-S70600

U “Positioning Media of Different Widths” on page 70 Note: If the label with black squares is not in place, affix the label as described in the Setup Guide. U Setup Guide E Align the media and the roll holders. Raise or lower the lifter until the...

[Page 40] Epson SureColor SC-S70600

I Rotate the handle until part A in the illustration below is fully inserted. c Important: Once part A is hidden, do not turn the handle any further. Failure to observe this precaution could damage the roll holder. If part A is not hidden even after ...

[Page 41] Epson SureColor SC-S70600

N Hold the center of the media and raise the media loading lever. O Pull the media straight forward until the edge has past the label on the left side of the after heater. Keep the right edge of the media parallel with the scale markings on the two l...

[Page 42] Epson SureColor SC-S70600

U “Using the Auto Take-up Reel Unit” on page 55 Note: If you would prefer to print from the very start of the roll, press the u button in the control panel to rewind the media slightly. Be sure, however, to stop rewinding before the leading edge ...

[Page 43] Epson SureColor SC-S70600

c Important: ❏ Do not use the media holding plates with media that is more than 0.4 mm thick. The media holding plates could touch and damage the print head. ❏ Move the media holding plates to the left and right edges of the platen when they are ...

[Page 44] Epson SureColor SC-S70600

Printable Side In If the label does not have the loading position, mark it on the label as instructed in the Setup Guide. U Setup Guide Note: Be sure the option selected for Roll Type in the Customize Settings menu matches how the media is rolled. Ro...

[Page 45] Epson SureColor SC-S70600

F Raise the lift lever on the right side of the printer to lift the media into position, then firmly insert the roll holder. If the roll of media has the outer diameter which is less than 140mm, lift it up by your hands, and set it to the roll holder...

[Page 46] Epson SureColor SC-S70600

Note: Media that is heavy and difficult to unroll can be fed by pressing the drive switch on the left roll holder. Printable Side Out Printable Side In K Insert the media past the pressure rollers and lower the media loading lever to hold it in pla...

[Page 47] Epson SureColor SC-S70600

For information on loading the media into the auto take-up reel unit, see: U “Using the Auto Take-up Reel Unit” on page 55 Note: If you would prefer to print from the very start of the roll, press the u button in the control panel to rewind the m...

[Page 48] Epson SureColor SC-S70600

c Important: ❏ Do not use the media holding plates with media that is more than 0.4 mm thick. The media holding plates could touch and damage the print head. ❏ Move the media holding plates to the left and right edges of the platen when they are ...

[Page 49] Epson SureColor SC-S70600

Printable Side In If the label does not have the loading position, mark it on the label as instructed in the Setup Guide supplied with the optional heavy roll media system. U Heavy Roll Media System Setup Guide Note: Be sure the option selected for R...

[Page 50] Epson SureColor SC-S70600

H Rotate the handle until part A in the illustration below is fully inserted. c Important: Once part A is hidden, do not turn the handle any further. Failure to observe this precaution could damage the roll holder. If part A is not hidden even after ...

[Page 51] Epson SureColor SC-S70600

L Go to the front of the printer and open the front cover. M Hold the center of the media and raise the media loading lever. N Pull the media straight forward until the edge has past the label on the left side of the after heater. Keep the right edge...

[Page 52] Epson SureColor SC-S70600

Note: If you would prefer to print from the very start of the roll, press the u button in the control panel to rewind the media slightly. Be sure, however, to stop rewinding before the leading edge of the media is over the cutter groove (on the press...

[Page 53] Epson SureColor SC-S70600

❏ Remaining Setup On: The printer displays the amount of media remaining. Off: The printer does not display the amount of media remaining. When Remaining Setup is On, the printer will calculate the approximate amount of media remaining based on the...

[Page 54] Epson SureColor SC-S70600

You can print the amount of media remaining on the leading edge of the roll before it is removed from the printer and then enter this number the next time the media is loaded for accurate information on the amount remaining. Note: The printer does no...

[Page 55] Epson SureColor SC-S70600

C Remove the media holding plates. D Cut the media with the cutter. Pass the blade of the cutter down the cutting groove. Note: ❏ If you are using the auto take-up reel unit, set the Auto switch on the auto take-up reel unit to Off before using the...

[Page 56] Epson SureColor SC-S70600

c Important: Note that the auto take-up reel unit may not function as expected when ink layering is performed with the SC-S70600 series or SC-S50600 series, causing a decline in print quality. Ink layering U “High Print Quality” on page 23 Attach...

[Page 57] Epson SureColor SC-S70600

c Important: Stop when part A is no longer visible. The take-up reel unit may not function as expected if the holder is inserted too far. F Tighten the roll core holder fixing screw to fix the roll core holder in place. See the following for further ...

[Page 58] Epson SureColor SC-S70600

E Lower the tensioner. F Press the d button to feed the media until the take up roll core begins to turn. c Important: The auto take-up reel unit will not function if the tensioner is raised. Clockwise Take Up A Attach the media to the take up roll c...

[Page 59] Epson SureColor SC-S70600

E Lower the tensioner. F Press the d button to feed the media until the take up roll core begins to turn. c Important: The auto take-up reel unit will not function if the tensioner is raised. Removing the Take-up Roll The procedure for removing media...

[Page 60] Epson SureColor SC-S70600

F Loosen the right roll core holder fixing screw and remove the roll core holder from the roll. G Lower the roll onto the roll support. Using the Optional Heavy Roll Auto Take-up Reel Unit This section explains how to remove media from the take-up re...

[Page 61] Epson SureColor SC-S70600

❏ Check the amount of ink remaining: If ink is expended during printing, printing can be resumed once the affected cartridge has been replaced. However, when replacing ink during a print job, you may see a difference in color depending on the dryin...

[Page 62] Epson SureColor SC-S70600

Buttons that are used in the following settings Choosing a Media Setting Bank A After confirming that the printer is ready, press the Menu button. The settings menu will be displayed. B Select Media Setup and press the Z button. C Use the d/u buttons...

[Page 63] Epson SureColor SC-S70600

Note: Feed Adjustment varies with the media used. Load the media for which feed adjustment is required under the same conditions as the actual print job. For example, if you are using the auto take-up reel unit for printing, the auto take-up reel uni...

[Page 64] Epson SureColor SC-S70600

Note: ❏ Head Alignment varies with the media used. Load the media that will be used in the actual print job. Head alignment is not available under the following conditions: ❏ The media is transparent or colored. ❏ The printer is exposed to dire...

[Page 65] Epson SureColor SC-S70600

For even, high-quality printing, select Printer Full Width. Multi-Strike Printing Choose the number of times each line is printed. A Use the d/u buttons to select Multi-Strike Printing and press the Z button. B Use the d/u buttons to choose a value. ...

[Page 66] Epson SureColor SC-S70600

Platen heater: 40 ˚C After heater: 50 ˚C Heater status can be viewed in the control panel. U “Understanding the Display” on page 20 Additional Dryer defaults to On; at this setting, the fan turns on automatically when printing starts. Additiona...

[Page 67] Epson SureColor SC-S70600

Buttons that are used in the following settings A After confirming that the printer is ready, press the Menu button. The settings menu will be displayed. B Select Media Setup and press the Z button. C Use the d/u buttons to select Customize Settings ...

[Page 68] Epson SureColor SC-S70600

❏ Enter a correction during printing and inspect the results. Note: Feed Adjustment varies with the media used. Load the media for which feed adjustment is required under the same conditions as the actual print job. For example, if you are using th...

[Page 69] Epson SureColor SC-S70600

K Pattern length is displayed in the control panel./ Using the d/u buttons, enter the value recorded in Step 10 and press the Z button. Secondary Adjustment L Perform Steps 1 to 6. M Use the d/u buttons to select Secondary and press the Z button twic...

[Page 70] Epson SureColor SC-S70600

Printable area SC-S70600 series/SC-S50600 series The printable area varies with the position of the media and the pressure rollers used. Positioning Media of Different Widths Position the media with reference to the positions of the pressure rollers....

[Page 71] Epson SureColor SC-S70600

Note: Pressure rollers not within the bounds indicated by the black labels do not apply pressure to the media when the media loading lever is lowered. Pressure rollers that are within a black label but not over the media will cause friction during pr...

[Page 72] Epson SureColor SC-S70600

A: Pressure rollers (low) *1 The value selected for Side Margin(Left) in the setup menu. The default value is 5 mm. Choose a Side Margin(Left) over 10 mm when using media holding plates. *2 The total of the values selected for Print Start Position an...

[Page 73] Epson SureColor SC-S70600

Varies with the option selected for Media Size Check. On selected for Media Size Check: The left edge of the media. Off selected for Media Size Check: 64 inches from the right edge reference position. 5mm 5mm 3-825mm* 2 3-25mm* 1 300-1626mm AB *1 The...

[Page 74] Epson SureColor SC-S70600

Maintenance Daily Maintenance To maintain print quality, perform the following inspection and cleaning before starting work each day. Cleaning the Platen Heater, Pressure Rollers, and Media Holding Plates ! Caution: ❏ The heaters and media holdin...

[Page 75] Epson SureColor SC-S70600

F Clean the media holding plates and platen heater. Dampen a soft cloth in water, wring it out thoroughly, and use it to remove lint and dust from the media holding plates on both the left and right sides and from the platen. Checking for clogged noz...

[Page 76] Epson SureColor SC-S70600

Buttons that are used in the following settings A After confirming that the printer is ready, press the # button. The Maintenance menu will be displayed. B Select Nozzle Check and press the Z button. C A nozzle pattern will be printed. When printing ...

[Page 77] Epson SureColor SC-S70600

Maintenance Procedures for Specialty Inks White and metallic silver inks are prone to precipitation (components settling to the bottom of the liquid). Perform the following maintenance to maintain print quality. ❏ Once every 24 hours, agitate the ...

[Page 78] Epson SureColor SC-S70600

Head Cleaning Level Choose from three levels of head cleaning. Select Execute (Light) first. If the pattern still contains faint or missing segments after head cleaning has been performed once, try again using Execute (Medium) or Execute (Heavy). Not...

[Page 79] Epson SureColor SC-S70600

F Head cleaning will be performed. The menu will close when cleaning is complete. Print a nozzle pattern and inspect the results to determine whether the problem has been resolved. U “Checking for clogged nozzles” on page 75 If you paused the pri...

[Page 80] Epson SureColor SC-S70600

❏ Use only the supplied cleaning sticks or sticks contained in maintenance kit (consumable kits, available separately). Other types of stick that produce lint will damage the print head. ❏ Always use fresh cleaning sticks. Re-using sticks can mak...

[Page 81] Epson SureColor SC-S70600

❏ Cleaning should also be performed if colors in the printout are faint or missing even after head cleaning has been performed. Clean the parts in the following order. (1) Print head (2) Wiper (3) Caps (4) Wiper rail Moving the Print Head This sect...

[Page 82] Epson SureColor SC-S70600

B Ink spatters on the base of the print head can be removed using an extremely small amount of ink cleaner applied to a clean room wiper (available in the market). SC-S70600 series/SC-S50600 series The print head on the left is Head 1, the print head...

[Page 83] Epson SureColor SC-S70600

If there is ink on the attachment points, remove the wiper for cleaning. Proceed to Step 2. B Remove the wiper. Holding the wiper by the attachment point, tilt it left and lift it out. C Clean the front and back of the wiper with a cleaning stick. D ...

[Page 84] Epson SureColor SC-S70600

F Return the wiper when cleaning is complete. Place on the attachment point and press down until you hear a click. If the remaining wiper for the SC-S70600 series or SC-S50600 series is stained, repeat the process from Step 1. G Clean the edges of th...

[Page 85] Epson SureColor SC-S70600

D Clean the area shown in the illustration. E Return the wiper cleaner that was removed in Step 2 to its original position. Place on the attachment point and press down until you hear a click. Users of the SC-S70600 series or SC-S50600 series will ne...

[Page 86] Epson SureColor SC-S70600

Note: If you replace the waste ink bottle before being prompted by a message in the control panel, reset the waste ink counter using the Waste Ink Counter option in the Maintenance menu. U “The Maintenance Menu” on page 106 c Important: Only rese...

[Page 87] Epson SureColor SC-S70600

Buttons that are used in the following settings A Confirm that the printer is on and press #. The Maintenance menu will be displayed. B Use the d/u buttons to select Head Maintenance and press the Z button. C Press the Z button to move the print head...

[Page 88] Epson SureColor SC-S70600

G Remove the wiper. Holding the wiper by the attachment point, tilt it left and lift it out. H Insert new wiper. Place on the attachment point and press down until you hear a click. Users of the SC-S70600 series or SC-S50600 series will need to retur...

[Page 89] Epson SureColor SC-S70600

E Remove the flushing pad. Grasp the tab as shown below and lift the pad out of the printer. Immediately transfer the used flushing pad to a tray. Ink may leak from the pad. F Insert a new flushing pad. Insert the two hooks on the flushing pad into t...

[Page 90] Epson SureColor SC-S70600

Regular Part Cleaning Check Sheet Print this page to track maintenance tasks. Component to be cleaned Cleaned on date Explanation A Platen heater, pressure rollers, media holding plates /////Clean if you notice lint from print media, dust, or ink sta...

[Page 91] Epson SureColor SC-S70600

Regular Replacement Check Sheet Print this page to track maintenance tasks. Component to be replaced Cleaned on date Explanation A Flushing pad / / / / / ❏ We recommend that this component be replaced once every six months. ❏ Replace when ink sta...

[Page 92] Epson SureColor SC-S70600

Replacing Ink Cartridges If one of the installed ink cartridges is expended, printing cannot be performed. If an ink low warning is displayed, we recommend replacing the ink cartridge(s) as soon as possible. If an ink cartridge runs out while printin...

[Page 93] Epson SureColor SC-S70600

E Fully insert the cartridge, keeping the color label to the front. Match the color of the cartridge to the color of the label on the printer. F Lower the lock lever to engage the latch. Repeat steps 2 to 6 to replace other ink cartridges. c Importan...

[Page 94] Epson SureColor SC-S70600

Using the Control Panel Menu Menu Operations The menus are used as shown below. EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Using the Control Panel Menu 94 ...

[Page 95] Epson SureColor SC-S70600

Menu List The following items and parameters can be set and executed in the Menu. See the reference pages for more details on each item. The SC-S30600 series does not support items or values marked with a superscript “1”, while items marked with ...

[Page 96] Epson SureColor SC-S70600

Menu Item Parameter Media Setup U “The Media Setup Menu” on page 100 Media Remaining Remaining Setup On, Off Length 5.0 to 99.5 m (15 to 300 ft) Remaining Alert 1 to 15 m (4 to 50 ft) Print Remaining Length Print Select Media RIP Settings, 1 to 3...

[Page 97] Epson SureColor SC-S70600

Menu Item Parameter Media Suction 0 to 10 Head Movement Data Width, Printer Full Width Multi-Strike Printing Off, 2 to 8 Roll Type Printable Side Out, Printable Side In Tension Measurement Periodically, Every Page, Off Media Tension 0 to 40 Feed Spee...

[Page 98] Epson SureColor SC-S70600

Menu Item Parameter Maintenance U “The Maintenance Menu” on page 106 Nozzle Check Print Cleaning All Nozzles Execute (Light), Execute (Medium), Execute (Heavy) Head 1/Head 2 1 , Head 1 1 , Head 2 1 Selected Nozzles Execute (Light), Execute (Mediu...

[Page 99] Epson SureColor SC-S70600

Menu Item Parameter Preference U “The Preference Menu” on page 109 Date And Time MM/DD/YY HH:MM Language Japanese, English, French, Italian, German, Portuguese, Spanish, Dutch, Russian, Korean, Chinese Unit: Length m, ft/in Unit: Temperature ˚C,...

[Page 100] Epson SureColor SC-S70600

Details of the Menu The SC-S30600 series does not support items or values marked with a superscript “1”, while items marked with a superscript “2” are available with the SC-S50600 series only. The Media Setup Menu The Media Setup menu can be ...