TP-Link TL-WA5210G Manual

Download or browse on-line these Installation Manual for TP-Link TL-WA5210G Wireless Access Point, Wireless Router.

TP-Link TL-WA5210G Manual Information:

This manual for TP-Link TL-WA5210G, given in the PDF format, is available for free online viewing and download without logging on. The guide contains 16 pages, and the size of the file at download is 27.07 Mb. The document type is Installation Manual.

Download Manual

More Manuals:

In case you failed to obtain relevant information in this document, please, look through related operating manuals and user instructions for TP-Link TL-WA5210G. Just click one of the links below to go to the selected manual:

Summary of Contents:

[Page 1] TP-Link TL-WA5210G

1 Typical network 1 Note The typical connection for TL-WA5210G is shown as above. Please make sure that the two CPEs are placed face to face, otherwise the wireless signal strength might be weak. Here shows several incorrect ...

[Page 2] TP-Link TL-WA5210G

2 Locate a suitable mounting site for your CPE. For choosing the best location, select an elevated location where trees, buildings and large steel structures will not obstruct the antenna signals and which offers maximum line-of-si...

[Page 3] TP-Link TL-WA5210G

3 The connection will be similar to the figure below after the above steps are finished. Turn on all your network devices and then check to see if the LEDs on the AP display normally as...

[Page 4] TP-Link TL-WA5210G

4 Login A dialog box will prompt you for the User name and Password.Ente r the default values and click OK. Note If the dialog box does not pop up, please refer to T3 in the Troubleshooting guide. T2 will give...

[Page 5] TP-Link TL-WA5210G

5 Operation Mode Setting 2 A. Configuration for AP Client Router Mode This page will then display. This page will then display. The AP supports three operation mode types: AP Client Router, A P Route r and AP. a)...

[Page 6] TP-Link TL-WA5210G

6 Click Finish B. Configuration for Point-to-Point Connection 1) The AP Setting Click Finish to exit the Quick Setup wizard and wait until the AP completes rebooting automatically. The changes will take effect after reb...

[Page 7] TP-Link TL-WA5210G

7 Click Wireless > Wireless Mode Select Client Enter TP-LINK_900008, the SSID of the first AP you have configured After successfully logging in, configure the other TL-WA5210G by following the steps below. 2) The Client Setting ...

[Page 8] TP-Link TL-WA5210G

8 Then click Save at the bottom of this page. Antenna Alignment A fter basic configuration of operation mode, you can change your CPE’s direction to get a better signal strength according to the parameters shown on the Ant...

[Page 9] TP-Link TL-WA5210G

9 Connect one side of the TL-ANT24SP to the RP-SMA port of your CPE through the TL-ANT24PT3. Connect the other side of the TL-ANT24SP to the TL-ANT2424B. Appendix 1: External antenna installation ...

[Page 10] TP-Link TL-WA5210G

10 Login Configure the external antenna ’ A dialog box will prompt you for the User name and Password.Ente r the default values and click OK. User name: admin Password: admin Click OK Open your web browse...

[Page 11] TP-Link TL-WA5210G

11 Note T1. How do I restore my AP’s configuration to its factory default settings? T2. What can I do if I forget my password? 1) Restore the AP’s configuration to its factory default settings. If you don’t know how ...

[Page 12] TP-Link TL-WA5210G

12 Double-click Internet Protocol ( TCP/IP ) Click Network Connections Click Properties Right-click Local Area Connection ...

[Page 13] TP-Link TL-WA5210G

13 For Windows 7 OS Go to Start > Settings > Control Panel, and then you will see the following page. Click View network status and tasks Click OK Select Use the following IP address Enter the 192.168.1.100 int...

[Page 14] TP-Link TL-WA5210G

14 Click Change adapter settings Click Properties Right-click Local Area Connection Double-click Internet Protocol Version 4 (TCP/IPv4) ...

[Page 15] TP-Link TL-WA5210G

15 Click OK Select Use the following IP address Enter the 192.168.1.100 into the IP address field, 255.255.255.0 into the Subnet mask field Enter the DNS server address provided by your ISP or network administrator S...

[Page 16] TP-Link TL-WA5210G

Technical Support  For more troubleshooting help, go to: www.tp-link.com/support/faq.asp  To download the latest Firmware, Driver, Utility and User Guide, go to: www.tp-link.com/support/download.asp  For all other technical suppo...