Scytek electronic VISIONGUARD 6000 Product Manual

Download or browse on-line these Product Manual for Scytek electronic VISIONGUARD 6000 Car Alarm.

Scytek electronic VISIONGUARD 6000 Manual Information:

This manual for Scytek electronic VISIONGUARD 6000, given in the PDF format, is available for free online viewing and download without logging on. The guide contains 36 pages, and the size of the file at download is 1.08 Mb. The document type is Product Manual.

Download Manual

Summary of Contents:

[Page 1] Scytek electronic VISIONGUARD 6000

VISIONGUARD 6000 VEHICLE SECURITY SYSTEM WITH BUILT-IN CAMERA AND A REMOTE START PRODUCT MANUAL ...

[Page 2] Scytek electronic VISIONGUARD 6000

Limited Lifetime Warranty This vehicle security system is warranted to the original purchaser, to be free from defects in material and workmanship. The manufacturer will repair or replace at its option, and free of charge for the first twelve (...

[Page 3] Scytek electronic VISIONGUARD 6000

1. About Your System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 1 2. Remote Transmitters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

[Page 4] Scytek electronic VISIONGUARD 6000

...

[Page 5] Scytek electronic VISIONGUARD 6000

The ScyTek VisionGuard 6000 is a combination vehicle security and remote starting system featuring a built- in "ScyNet Network Port" that allows direct connection of optional accessory modules and a PC interface offering expanded system ope...

[Page 6] Scytek electronic VISIONGUARD 6000

Standard Remote Transmitter Description The VisionGuard 6000 is compatible with the optional 5-button Remote Transmitters used to control system operations. Note: Using the optional PC or Pocket PC interface with the network software, it is possibl...

[Page 7] Scytek electronic VISIONGUARD 6000

Adding/Replacing Transmitters To replace lost or stolen transmitters or to add additional transmitters into the system, have all desired transmitters ready and follow the steps below. Note: Up to 4 transmitters can be programmed to operate the syst...

[Page 8] Scytek electronic VISIONGUARD 6000

Page 4 - VisionGuard 6000 True Color 2-way Camera Ready Remote Transmitter Description The VisionGuard 6000 True Color 2-way LCD remote transmitter, is offering increased range and confirmation of any activated features. Button 1 Arms the system....

[Page 9] Scytek electronic VISIONGUARD 6000

VisionGuard 6000 - Page 5 4. Turn off the ignition key. 5. Repeat steps 1-4 to add an additional 2-way transmitter. System Confirmation The 2-way transmitter's confirmation feature allows the current vehicle status to be displayed at any tim...

[Page 10] Scytek electronic VISIONGUARD 6000

Page 6 - VisionGuard 6000 Camera Features ...

[Page 11] Scytek electronic VISIONGUARD 6000

VisionGuard 6000 - Page 7 ...

[Page 12] Scytek electronic VISIONGUARD 6000

Page 8 - VisionGuard 6000 Remote Arming The system monitors 6 independent areas ( zones ) while armed: doors, hood, trunk, shock sensor, optional sensor input, and the network port for future expansion. To Arm the System: 1. Turn off the ignition. ...

[Page 13] Scytek electronic VISIONGUARD 6000

VisionGuard 6000 - Page 9 Tamper Alert If the system was triggered while away, the LED will flash to indicate which zone triggered the system after disarming and turning on the ignition. The LED indication will repeat 8 times. LED Flashes (60 seco...

[Page 14] Scytek electronic VISIONGUARD 6000

Page 10 - VisionGuard 6000 Panic Mode In the event of an emergency the transmitter’s remote Panic feature can be used to instantly trigger the alarm. To activate the Panic Mode: 1. Press and hold Button 1 for 3 seconds. · The alarm will sound. �...

[Page 15] Scytek electronic VISIONGUARD 6000

VisionGuard 6000 - Page 11 To set the Emergency Override Code: 1. Turn on ignition. 2. Within 5 seconds, press the valet switch 5 times. · The siren will provide one long chirp, indicating that you have entered Programming. 3. Press the valet swit...

[Page 16] Scytek electronic VISIONGUARD 6000

Page 12 - VisionGuard 6000 Remote Starting To Remote Start the System: 1. Be sure the system is not in Valet Mode. 2. Press and hold Button 4 for three seconds. · The parking lights will flash 4 times and turn on. · The Siren will chirp 4 times....

[Page 17] Scytek electronic VISIONGUARD 6000

VisionGuard 6000 - Page 13 Turbo Timer Feature The Turbo Timer feature allows vehicles with turbocharged engines to remain running after the ignition key is removed, for proper cool-down of the turbocharger. The Turbo Timer feature requires connec...

[Page 18] Scytek electronic VISIONGUARD 6000

Page 14 - VisionGuard 6000 Extended Features Ignition Door Locking For added safety, the Ignition Door Locking feature allows vehicles equipped with power door lock systems to automatically lock the doors when the ignition is turned on. If a doo...

[Page 19] Scytek electronic VISIONGUARD 6000

VisionGuard 6000 - Page 15 1. Thoroughly read and become familiar with the installation instructions before beginning the installation. 2. Review system contents: Main Unit Two 5-Button Remote Transmitters Siren Shock Sensor Harnesses • 6-Pin s...

[Page 20] Scytek electronic VISIONGUARD 6000

Page 16 - VisionGuard 6000 Mounting the Control Unit The control unit must only be mounted in the interior of the vehicle. Do not mount the main unit in the engine compartment. Choose a mounting location that will not be easily accessible to a thi...

[Page 21] Scytek electronic VISIONGUARD 6000

VisionGuard 6000 - Page 17 System Wiring 6-Pin Starter Harness Pin 1 RED WIRE A: Main Power Input A (+). Connect to the battery or constant power wire at the ignition switch with a minimum 25 Amp supply. Remove the fuse until the installation is...

[Page 22] Scytek electronic VISIONGUARD 6000

Page 18 - VisionGuard 6000 when the door is open. This type of door circuit is usually found on Ford vehicles. Pin 12 GREEN WIRE: Negative Door Input (-). Connect to the door switch circuit wire that shows ground when the door is open. Pin 13 WHI...

[Page 23] Scytek electronic VISIONGUARD 6000

VisionGuard 6000 - Page 19 Jumper Selection Carefully separate the top and bottom halves of the main unit case. Once the cover is removed, the parking light polarity jumper will be visible next to the parking light relay. Set the jumper for the c...

[Page 24] Scytek electronic VISIONGUARD 6000

Page 20 - VisionGuard 6000 Entering System Programming This system is compatible with both the optional LCD transmitter or the standard AM transmitter, all system programming can be performed using either one. To enter System Programming: 1. Turn on...

[Page 25] Scytek electronic VISIONGUARD 6000

VisionGuard 6000 - Page 21 5. Ignition Door Unlocking. Selects whether or not the system automatically unlocks the doors when the ignition is turned off. The Ignition Door Locking feature may be programmed to unlock all doors or the driver’s door...

[Page 26] Scytek electronic VISIONGUARD 6000

Page 22 - VisionGuard 6000 8. Passive Door Locking. Selects whether or not the system will automatically lock the doors during Passive Arming and Auto Rearming mode. 9. Passive Arming Entry Delay. When selected, the siren will chirp for 10 seconds ...

[Page 27] Scytek electronic VISIONGUARD 6000

VisionGuard 6000 - Page 23 Diesel Engine. Sets the engine type for Diesel and monitors the glow plug input to make sure the glow plugs are warm before cranking the starter. If the glow plug wire is not connected, the built-in timer waits 15 second...

[Page 28] Scytek electronic VISIONGUARD 6000

Page 24 - VisionGuard 6000 Wiring Diagrams TO POSITIVE DOME LIGHT +12V Black/White (-) DOME LIGHT OUTPUT TO NEGATIVE DOME LIGHT +12V Black/White (-) DOME LIGHT OUTPUT Positive Dome Light Negative Dome Light TO POSITIVE HORN WIRE +12V Brown/Whi...

[Page 29] Scytek electronic VISIONGUARD 6000

VisionGuard 6000 - Page 25 Negative Trigger Positive Trigger Reverse Polarity Vacuum Adding Actuators Follow the diagrams below for connecting basic door lock systems. For Two Stage door lock systems (separately unlocks driver and passenger doors)...

[Page 30] Scytek electronic VISIONGUARD 6000

Page 26 - VisionGuard 6000 Two Stage Door Lock Diagrams Two Stage Negative Trigger Two Stage Positive Trigger The VisionGuard 6000 is equipped with a dedicated Passenger Unlock output allowing Two Stage Door Lock operation. When connect...

[Page 31] Scytek electronic VISIONGUARD 6000

VisionGuard 6000 - Page 27 Two Stage Door Lock Diagrams cont’d Two Stage Reverse Polarity Two Stage Adding Actuators ...

[Page 32] Scytek electronic VISIONGUARD 6000

Page 28 - VisionGuard 6000 FCC ID: OARRXAM2000 This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions: 1) This device may not cause harmful interference. 2) This device must accept any interference recei...

[Page 33] Scytek electronic VISIONGUARD 6000

VisionGuard 6000 - Page 29 Starter Diagnostics Starter doesn’t start and Side Lights flash: 3 Times - Engine RPM not detected Hood Trigger is active 4 Times - Brake Trigger is active 5 Times - Unit is in Valet (service) mode, and start is di...

[Page 34] Scytek electronic VISIONGUARD 6000

Page 30 - VisionGuard 6000 ...

[Page 35] Scytek electronic VISIONGUARD 6000

VisionGuard 6000 - Page 31 ...

[Page 36] Scytek electronic VISIONGUARD 6000

ScyTek Electronics 11627 Cantara Street North Hollywood, CA 91605 © ScyTek Electronics 2005 VisionGuard 6000 r3 11/05 Wiring Diagram ScyNet Blue Start (-) Green Emergency brake(-) Antenna with built -in Camera Shock Sensor LED Valet Switch Green ...