Dialogic TX4000 PCI SS7 Installation Manual

Download or browse on-line these Installation Manual for Dialogic TX4000 PCI SS7 Network Card.

Dialogic TX4000 PCI SS7 Manual Information:

This manual for Dialogic TX4000 PCI SS7, given in the PDF format, is available for free online viewing and download without logging on. The guide contains 48 pages, and the size of the file at download is 0.95 Mb. The document type is Installation Manual.

Download Manual

Summary of Contents:

[Page 1] Dialogic TX4000 PCI SS7

Dialogic® TX 4000 PCI SS7 Network Interface Board Installation Manual July 2009 64-0429-01 www.dialogic.com ...

[Page 2] Dialogic TX4000 PCI SS7

Copyright and legal notices Copyright © 2003-2009 Dialogic Corporation. All Rights Reserved. You may not reproduce this document in whole or in part without permission in writing from Dialogic Corporation at the address provided below. All conten...

[Page 3] Dialogic TX4000 PCI SS7

Revision history Revision Release date Notes 62334-10 November 2003 SRR, SS7 4.0 Beta 62334-11 April 2004 SRR, SS7 4.0 62334-12 August 2004 SRR. SS7 4.1 62334-13 April 2005 LBG, SS7 4.2 62334-14 July 2008 LBG, SS7 5.0 64-0429-...

[Page 4] Dialogic TX4000 PCI SS7

...

[Page 5] Dialogic TX4000 PCI SS7

Table Of Contents Chapter 1: Introduction ..........................................Error! Bookmark not defined. Chapter 2: Dialogic® TX 4000 PCI SS7 Network Interface Board Installation Manual......................................................

[Page 6] Dialogic TX4000 PCI SS7

Introduction TX 4000 PCI SS7 Network Interface Board Installation Manual Chapter 8: Hardware specifications .............................................................43 General hardware specifications ............................................

[Page 7] Dialogic TX4000 PCI SS7

1 1 Introduction The Dialogic ® TX 4000 PCI SS7 Network Interface Board Installation Manual explains how to perform the following tasks: • Install the TX 4000 PCI SS7 Network Interface board • Configure the TX 4000 PCI SS7 Netwo...

[Page 8] Dialogic TX4000 PCI SS7

...

[Page 9] Dialogic TX4000 PCI SS7

2 2 Overview of the TX 4000 board TX 4000 board features The Dialogic ® TX 4000 PCI SS7 Network Interface board is a PCI board that provides four T1 or E1 digital trunk interfaces and two Ethernet 10/100Base-T interfaces. The TX 4000...

[Page 10] Dialogic TX4000 PCI SS7

Overview of the TX 4000 board TX 4000 PCI SS7 Network Interface Board Installation Manual The following illustration shows the TX 4000 board: T1/E1 trunk connectors Ethernet connectors T1/E1 status LEDs Ethernet MAC/PHY chips Framer Host bridg...

[Page 11] Dialogic TX4000 PCI SS7

TX 4000 PCI SS7 Network Interface Board Installation Manual Overview of the TX 4000 board • Telephony bus switching Switching for the TX 4000 board offers support for the H.100 bus within the H.100 architecture. On the TX 4000 board, switch c...

[Page 12] Dialogic TX4000 PCI SS7

Overview of the TX 4000 board TX 4000 PCI SS7 Network Interface Board Installation Manual Utilities and demonstration programs NaturalAccess Signaling Software provides the following utilities and demonstration programs for the TX 4000 board. R...

[Page 13] Dialogic TX4000 PCI SS7

TX 4000 PCI SS7 Network Interface Board Installation Manual Overview of the TX 4000 board NaturalAccess™ Signaling Software provides the following programs in compiled and uncompiled form to demonstrate the usage of the TDM libraries. For infor...

[Page 14] Dialogic TX4000 PCI SS7

...

[Page 15] Dialogic TX4000 PCI SS7

3 3 Installing the TX 4000 board System requirements To install and use the TX 4000 board, your system must have the following components: • An available PCI bus slot. • At least 8 MB of memory (excluding operating system require...

[Page 16] Dialogic TX4000 PCI SS7

Installing the TX 4000 board TX 4000 PCI SS7 Network Interface Board Installation Manual Installation summary The following table summarizes the steps for initially installing the hardware and software components: Step Description For detai...

[Page 17] Dialogic TX4000 PCI SS7

TX 4000 PCI SS7 Network Interface Board Installation Manual Installing the TX 4000 board Configuring the hardware This topic describes the following procedures for configuring the TX 4000 board: • Configuring H.100 bus termination • Confi...

[Page 18] Dialogic TX4000 PCI SS7

Installing the TX 4000 board TX 4000 PCI SS7 Network Interface Board Installation Manual The following illustration shows the H.100 termination DIP switch: S2 OFFON 12 34 567 8 Configuring SS7 Monitor mode DIP switch S3 controls the SS7 Mon...

[Page 19] Dialogic TX4000 PCI SS7

TX 4000 PCI SS7 Network Interface Board Installation Manual Installing the TX 4000 board DIP switch S1 DIP switch S1 controls the operation of the board. By default, only switch 2 (AUTOSTART) is set to the ON position; all other S1 switches are ...

[Page 20] Dialogic TX4000 PCI SS7

Installing the TX 4000 board TX 4000 PCI SS7 Network Interface Board Installation Manual Installing the board Complete the following steps to install the TX 4000 board in your system: Step Action 1 If necessary, configure the board as descri...

[Page 21] Dialogic TX4000 PCI SS7

4 4 Configuring the TX 4000 board Using the configuration utility After you install the TX 4000 board and the NaturalAccess Signaling Software, you must assign a CP number to each TX 4000 board. Verify that you have completed the steps ...

[Page 22] Dialogic TX4000 PCI SS7

Configuring the TX 4000 board TX 4000 PCI SS7 Network Interface Board Installation Manual Assigning a CP number Complete the following steps to assign a CP number to an installed TX board: Step Action 1 Power up the system if it is not runni...

[Page 23] Dialogic TX4000 PCI SS7

TX 4000 PCI SS7 Network Interface Board Installation Manual Configuring the TX 4000 board Adding a board Complete the following steps to add a new undefined TX 4000 board: Step Action 1 Power down the system if it is running. 2 Insert the T...

[Page 24] Dialogic TX4000 PCI SS7

Configuring the TX 4000 board TX 4000 PCI SS7 Network Interface Board Installation Manual Changing a CP number Complete the following steps to change the CP number of a TX board: Step Action 1 At the prompt, invoke txcpcfg by entering the fo...

[Page 25] Dialogic TX4000 PCI SS7

TX 4000 PCI SS7 Network Interface Board Installation Manual Configuring the TX 4000 board Moving a board Complete the following steps to move a TX board from one slot to another slot: Step Action 1 Power down the system if it is running. 2 ...

[Page 26] Dialogic TX4000 PCI SS7

Configuring the TX 4000 board TX 4000 PCI SS7 Network Interface Board Installation Manual Removing a board Complete the following steps to remove a TX board from the system: Step Action 1 Power down the system if it is running. 2 Remove t...

[Page 27] Dialogic TX4000 PCI SS7

TX 4000 PCI SS7 Network Interface Board Installation Manual Configuring the TX 4000 board Saving configuration changes In a Windows system, any changes that you make to the configuration information with the txcpcfg utility are saved automatical...

[Page 28] Dialogic TX4000 PCI SS7

...

[Page 29] Dialogic TX4000 PCI SS7

5 5 Establishing network connections Connectors and cables The TX 4000 board has two Dialogic ® MD1 RJ-45 T1/E1 trunk interfaces and two Ethernet connectors. The following illustration shows these connectors on the TX 4000 end bracke...

[Page 30] Dialogic TX4000 PCI SS7

Establishing network connections TX 4000 PCI SS7 Network Interface Board Installation Manual Dual T1/E1 120 ohm adapter cable The following illustration shows a dual T1/E1 120 ohm trunk adapter cable: Dialogic® MD1 RJ-45 Length: 4 “ RJ-48...

[Page 31] Dialogic TX4000 PCI SS7

TX 4000 PCI SS7 Network Interface Board Installation Manual Establishing network connections Connecting to the network Before connecting a TX 4000 board to the network, ensure that you have properly configured the trunks as either T1 or E1. For ...

[Page 32] Dialogic TX4000 PCI SS7

Establishing network connections TX 4000 PCI SS7 Network Interface Board Installation Manual E1 network considerations TX 4000 boards can support up to four CEPT E1 trunk interfaces. For typical E1 communications, each E1 interface connects dir...

[Page 33] Dialogic TX4000 PCI SS7

TX 4000 PCI SS7 Network Interface Board Installation Manual Establishing network connections Testing in loopback mode You can connect the board in loopback mode to test the digital trunk application without connecting to the telephone network. T...

[Page 34] Dialogic TX4000 PCI SS7

Establishing network connections TX 4000 PCI SS7 Network Interface Board Installation Manual Connecting TX boards for redundancy Use the redundancy feature to enable the system to detect and recover from the failure of signaling links on a TX 4...

[Page 35] Dialogic TX4000 PCI SS7

TX 4000 PCI SS7 Network Interface Board Installation Manual Establishing network connections Single-node redundant signaling server The following illustration shows how to set up two TX 4000 boards based on the single-node signaling server in a ...

[Page 36] Dialogic TX4000 PCI SS7

Establishing network connections TX 4000 PCI SS7 Network Interface Board Installation Manual Dual-node redundant signaling server The following illustration shows how to set up two TX 4000 boards based on a dual- node redundant signaling server ...

[Page 37] Dialogic TX4000 PCI SS7

6 6 Verifying the installation External connection status LEDs The TX 4000 board provides LEDs to indicate the status of the trunk interfaces. The location of the LEDs is shown in the following illustration: Trunk 1 (and Trunk 3 if ap...

[Page 38] Dialogic TX4000 PCI SS7

Verifying the installation TX 4000 PCI SS7 Network Interface Board Installation Manual Ethernet LEDs The TX 4000 board provides two LEDs to indicate the status of each Ethernet interface. The LEDs are located in the RJ-45 connectors as shown in...

[Page 39] Dialogic TX4000 PCI SS7

TX 4000 PCI SS7 Network Interface Board Installation Manual Verifying the installation Board status LEDs In addition to external connection status LEDs and Ethernet LEDs, the following banks of LEDs (D6-D21) located on the back of the TX 4000 bo...

[Page 40] Dialogic TX4000 PCI SS7

Verifying the installation TX 4000 PCI SS7 Network Interface Board Installation Manual Status LEDs After the boot code LEDs become green, the status LEDs are active and indicate the current board status as described in the following table: LED...

[Page 41] Dialogic TX4000 PCI SS7

TX 4000 PCI SS7 Network Interface Board Installation Manual Verifying the installation Verifying the board installation Complete the following steps to verify that each board is successfully installed: Step Action 1 Display a list of all of t...

[Page 42] Dialogic TX4000 PCI SS7

...

[Page 43] Dialogic TX4000 PCI SS7

7 7 Hardware specifications General hardware specifications This topic describes the following types of hardware specifications: • Physical • Host interface • H.100 compliant interface • Environment • Software environm...

[Page 44] Dialogic TX4000 PCI SS7

Hardware specifications TX 4000 PCI SS7 Network Interface Board Installation Manual H.100 compliant interface H.100 compliant interface has the following features: • Flexible connectivity between T1 and E1 trunks and the H.100 bus • Acce...

[Page 45] Dialogic TX4000 PCI SS7

TX 4000 PCI SS7 Network Interface Board Installation Manual Hardware specifications CEPT E1 G.703 telephony interface Feature Specification Interface G.703 2048 kbit/s trunk interface Line code HDB3 (in zero code suppression) or AMI Alarm s...

[Page 46] Dialogic TX4000 PCI SS7

...

[Page 47] Dialogic TX4000 PCI SS7

Index A adding a board 23 assigning a CP number 22 B boot code LEDs 39 bracket 20 C cables 15 crossover 33 dual T1/E1 trunk adapter 29 for redundancy 34 network 31 CEPT E1 G.703 telephony interface 45 changing a CP number 24 commun...

[Page 48] Dialogic TX4000 PCI SS7

Index Dialogic® TX 4000 PCI SS7 Network Interface Board Installation Manual loopback mode 33 M MD1 RJ-45 interface 29 N NaturalAccess 11, 15 network connections 31 connectors and cables 29 for redundancy 34 testing in loopback mode 33 NMS...