Norcross ML100TDR ML100R ML100DR ML100tr Instruction Manual

Download or browse on-line these Instruction Manual for Norcross ML100TDR ML100R ML100DR ML100tr Fish Finder.

Norcross ML100TDR ML100R ML100DR ML100tr Manual Information:

This manual for Norcross ML100TDR ML100R ML100DR ML100tr, given in the PDF format, is available for free online viewing and download without logging on. The guide contains 21 pages, and the size of the file at download is . The document type is Instruction Manual.

Download Manual

Summary of Contents:

[Page 1] Norcross ML100TDR ML100R ML100DR ML100tr

...

[Page 2] Norcross ML100TDR ML100R ML100DR ML100tr

2. Clean and dry both the selected area and the face of the transducer with a weak solvent to remove any dust, grease or oil. 3. If the hull temperature is above 15º C (60º F), mix the epoxy until the color is uniform. Do not proceed if the hull te...

[Page 3] Norcross ML100TDR ML100R ML100DR ML100tr

FIGURE 10C If the hull surface is not smooth, grind it with a disc sander. Partially fill a thin plastic bag with water, place the transducer inside and close it tightly with a tie wrap. Wet the surface of the hull and press the transducer face again...

[Page 4] Norcross ML100TDR ML100R ML100DR ML100tr

FIGURE 10A • This method is practical if the transducer will be located near the stern and the boat has a low deadrise angle. Clean away any large build-up of grease and / or dirt. Place the transducer against the hull and allow bilge water to cove...

[Page 5] Norcross ML100TDR ML100R ML100DR ML100tr

Testing the Depth Sounder Establish a performance baseline by operating the depth sounder with the transducer directly in the water. The results of this test are used as a basis of comparison to determine the best in-hull location for the transducer....

[Page 6] Norcross ML100TDR ML100R ML100DR ML100tr

Never use adhesive to fill gaps between the trans- ducer and the hull since this will greatly reduce performance (Figure 18). Headroom Choose a location with enough headroom inside the boat to complete the installation. Hull material Since the hul...

[Page 7] Norcross ML100TDR ML100R ML100DR ML100tr

Figure 17 Outboard Inboard/Outboard Inboard Sailboat 31 1. Upon applying power to the transmitter and receiver, place the display over the transmitter. Refer to Figure 1 for proper alignment. IMPORTANT!!!! Before Installing the ML100DR and ML100R, ...

[Page 8] Norcross ML100TDR ML100R ML100DR ML100tr

L o c at i o n Consult the boat manufacturer for the best in-hull transduc- er placement. If this information is unavailable, follow the guidelines below and see Figure . • Outboard powerboats - Install as far aft as is practical • Inboard / ou...

[Page 9] Norcross ML100TDR ML100R ML100DR ML100tr

IN-HULL TRANSDUCER INSTALLATION INSTRUCTIONS Applications • Recommended for high speed boats to eliminate the acoustic noise generated by external mounting • For hulls with a deadrise angle less than 10 degrees IMPORTANT!!!! Please read the instr...

[Page 10] Norcross ML100TDR ML100R ML100DR ML100tr

4. Consult the dealer or an experienced radio/TV technician for help The Portable Wireless Depth Sounder Display (ML100R) Will Not Turn On 1. Place in the charging cradle and recharge. 2. If after charging the display still will not turn on, contact...

[Page 11] Norcross ML100TDR ML100R ML100DR ML100tr

“E--” Appears on the Display: This indicates that there is no RF signal being received from the transmitter . 1. Make sure that there is power to the transmitter. (A red or green LED on the transmitter will indicate power) 2. Move within range ...

[Page 12] Norcross ML100TDR ML100R ML100DR ML100tr

2. If this condition occurs only at high speeds, then a transducer adjustment is needed. Refer to the Transducer Installation Instructions for adjustment procedure. 3. Check the transducer cable connection to the trans- mitter. Make sure th...

[Page 13] Norcross ML100TDR ML100R ML100DR ML100tr

TROUBLESHOOTING There are no user repairable parts within this equipment. Attempting to repair it yourself will only void the warranty. If you have a problem with your ML100Series, consult the fol- lowing troubleshooting guide. If this does not rem...

[Page 14] Norcross ML100TDR ML100R ML100DR ML100tr

Adjustable Surface Mounting Bracket For ML100DR Display (Part Number - MB01) Portable Transducer Bracket Kit For P23 Transducer (Part Number - 33-173) Adjustable Surface Mounting Bracket For ML100R Display (Part Number - MB02) Accessories To purc...

[Page 15] Norcross ML100TDR ML100R ML100DR ML100tr

Readout 2.5’-99.9’,100’-250’ Units of Measure Feet and Meters Transducer Frequency 200KHz Transducer Power 250W (max) Beam Angle 25 degree, -10db Depth Range Max 200 feet Depth Range Min 2.5 ...

[Page 16] Norcross ML100TDR ML100R ML100DR ML100tr

If the problems are related to depth readings, please send the transducer along with the unit when sending for repair. We will not under any circumstances be liable to anyone for any special, consequential, incidental, or other indirect damage of any...

[Page 17] Norcross ML100TDR ML100R ML100DR ML100tr

NORCROSS LIMITED WARRANTY NorCross Marine Products, Inc. warrants, to the original purchaser, this product to be free from defects in materials and workmanship for two years from the date of purchase. If the unit fails to perform as described in the...

[Page 18] Norcross ML100TDR ML100R ML100DR ML100tr

2 Year Limited Warranty What Does Our Warranty Cover? - Any defect in material or workmanship For How Long After the Original Purchase? - 2 Years What Will NorCross Do? - At our option repair or replace. How Do I Obtain Service? - Securely pack the u...

[Page 19] Norcross ML100TDR ML100R ML100DR ML100tr

2. The "UP" key will increase the selected value. The "DOWN" key will reduce the value. Pressing either key will change the value in 1-foot increments. Holding down the key will change the value in 9 foot increments per second....

[Page 20] Norcross ML100TDR ML100R ML100DR ML100tr

Figure 4 ...

[Page 21] Norcross ML100TDR ML100R ML100DR ML100tr

1. Upon applying power to the transmitter and receiver, place the display over the transmitter. Refer to Figure 1 for proper alignment. IMPORTANT!!!! Before Installing the ML100DR and ML100R, it will be necessary to match the receiver to ...