Goodman GSASD-10 Installation, Operation And Service Instructions

[Page 1] Goodman GSASD-10

INSTALLATION, OPERATION AND SERVICE INSTRUCTIONS MODELS GSASD-10, GSASD-11, GSASD-12, GSASD-18 ASASD-10, ASASD-11, ASASD-12, ASASD-18 ELECTRONIC AIR CLEANERS IMPORTANT: PLEASE READ MANUAL BEFORE OPERATING UNIT ...

[Page 2] Goodman GSASD-10

CONTENTS Certified for shock and electrical fire hazard only. SAFETY CONSIDERATIONS Read and follow instructions carefully. Follow all local electrical codes during installation. All wiring must conform to local and national electrical cod...

[Page 3] Goodman GSASD-10

area where they are attracted to a series of grounded plates. Pollutants are held in this section like a magnet until washed away during cleaning. Lastly, clean air passes over activated carbon filters (3) for odor removal. The Electronic Air...

[Page 4] Goodman GSASD-10

Installation Location With Humidifier A humidifier should be installed in the furnace warm air duct. However, it may be installed in the return duct without causing problems to the Air Cleaner. Care must be taken to ensure that the humidifier...

[Page 5] Goodman GSASD-10

5 Fig. 5 — Air Cleaner Schematic (with Air Proving Switch) Electronic Air Cleaner Installation 1. Remove existing equipment filter. Thoroughly clean fan compartment and ductwork where Air Cleaner is to be installed. 2. Open access door....

[Page 6] Goodman GSASD-10

Note: There may be some arcing or snapping sounds from the collecting cells. This is normal when the unit is new. In about 2 weeks, as the sharp edges of the cells become smoother, the arcing will disappear. OPERATION The Air Cleaner will...

[Page 7] Goodman GSASD-10

installer or dealer. To replace filters, perform the following functions: 1. Turn Air Cleaner power switch OFF. 2. Turn off system fan. 3. Open access door. 4. Remove collecting cells from Air Cleaner. 5. Remove the used carbon filters ...

[Page 8] Goodman GSASD-10

3. Push the light out through front of power box. 4. Push the new light into the power box. 5. Connect the wiring to the LED terminals on the power board. P3 - red; P4 - black. Route the wires away from the high voltage wires or contacts. ...

[Page 9] Goodman GSASD-10

without the transformer connected. Resistance should read above 20K ohms with an analog meter and above 4M ohms with a digital meter. If the resistance readings are below these values, the power board may be the cause of the transformer failu...

[Page 10] Goodman GSASD-10

1. With the ohmmeter set on its lowest scale, take a reading between the top center contact of the cell and the ionizing fingers on the bottom of the cell. You should have continuity. If you do not then there is a bad contact between the cen...

[Page 11] Goodman GSASD-10

# Part Description GSASD-10 GSASD-11 GSASD-12 GSASD-18 1 On/Off Switch R1-0205 R1-0205 R1-0205 R1-0205 2 Safety Interlock Switch R1-0202 R1-0202 R1-0202 R1-0202 3 Performance Indicator Light (Green LED) R1-0123 R1-0123 R1-01...

[Page 12] Goodman GSASD-10

12 PROBLEM PROBABLE CAUSE REMEDY System fan is not on. Turn system fan on. Wiring improperly connected. Check wiring or if plug is inserted and receptacle is powered. Defective power switch. Check power switch for continuity with ohmmete...

[Page 13] Goodman GSASD-10

Cleaning Record The collecting cells and prefilters must be cleaned on a regular basis for the Air Cleaner to function at its peak efficiency. The frequency of cleaning will vary from one house to another. On average, the cells should be cle...

[Page 14] Goodman GSASD-10

NOTES: 14 ...