Heat & Glo SL-350TRSI-AUE Installation And Operation Instructions Manual

[Page 1] Heat & Glo SL-350TRSI-AUE

1 Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06 MODEL: SL-350TRSI-AUE AUSTRALIAN GAS ASSOCIATION APPROVED Approval Number 5666 THIS MANUAL MUST BE USED FOR INSTALLATION AND RETAINED BY HOMEOWNER FOR OPERATION AND MAINTENANCE...

[Page 2] Heat & Glo SL-350TRSI-AUE

2 Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06 IMPORTANT: Read all instructions carefully before starting installation. Failure to follow these installation instructions may result in a possible fire hazard and will void the ...

[Page 3] Heat & Glo SL-350TRSI-AUE

3 Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06 TABLE OF CONTENTS 1.0 Installation Instructions......................................................................................... 5 1.1 Introduction .........................

[Page 4] Heat & Glo SL-350TRSI-AUE

4 Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06 Figure 1. Diagram of SL-350TRSI-AUE 22-3/4 in. (577mm) 11-3/8 in. (289mm) 16-3/8 in. (414mm) 8-3/4 in. (223mm) 15-7/8 in. (402 mm) Ø6-5/8 in. (167mm) 24 in. (610mm) 5-5/8 in. (...

[Page 5] Heat & Glo SL-350TRSI-AUE

5 Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06 Figure 2. Fireplace Dimensions, Locations, and Space Requirements 1.0 INSTALLATION INSTRUCTIONS Clearance Requirements The top and back of fireplace are defined by stand-offs. Th...

[Page 6] Heat & Glo SL-350TRSI-AUE

6 Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06 Figure 4. Framing Dimensions Framing should be constructed of 2 X 4 lumber or heavier. The framing headers may rest on the fireplace stand-offs. AB CD*E* 34" 30-5/8"...

[Page 7] Heat & Glo SL-350TRSI-AUE

7 Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06 NOTES: 1. All distances are measured vertically or horizontally along the wall to a point in line with the nearest part of the terminal. 2. Prohibited area below electricity mete...

[Page 8] Heat & Glo SL-350TRSI-AUE

8 Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06 TABLE 1 1.2 FLUE SYSTEM APPROVALS These models have flue starting collars on both the top and the back of the unit. Depending upon the installa- tion, decide which ONE set of st...

[Page 9] Heat & Glo SL-350TRSI-AUE

9 Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06 NOTE: PIPES OVERLAP 32mm AT EACH JOINT. D V P 9 0 S T 319mm 286mm 184mm 32mm TYP 13mm TYP 217mm DVP36 DVP48 1219mm 610mm 914mm 102mm 152mm DVP4 DVP6 305mm DVP12 51mm MIN. DVP12A...

[Page 10] Heat & Glo SL-350TRSI-AUE

10 Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06 Figure 8. SL D-Series Balanced Flue Component Specifications (102mm inner pipe / 168mm outer pipe) NOTE: PIPES OVERLAP 35mm AT EACH JOINT. 168mm 244mm 162mm 162mm 165mm 244mm...

[Page 11] Heat & Glo SL-350TRSI-AUE

11 Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06 VERTICAL FLUEING V FT. (M) 36' MAXIMUM (10.97M) Figure 10. USE SL D-SERIES COMPONENTS ONLY. Figure 11. USE DVP-SERIES COMPONENTS ONLY. STRAIGHT OUT HORIZONTAL FLUEING H Ma...

[Page 12] Heat & Glo SL-350TRSI-AUE

12 Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06 Figure 12. V H FT. (M) FT. (M) 1' MIN.(0.30M) 2' MAX.(0.61M) 2' MIN.(0.61M) 4' MAX.(1.22M) 3' MIN.(0.91M) 8&...

[Page 13] Heat & Glo SL-350TRSI-AUE

13 Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06 Figure 14. V H FT. (M) FT. (M) 1' MIN.(0.30M) 2' MAX.(0.61M) 2' MIN.(0.61M) 4' MAX. (1.22M) 3' MIN.(0.91M) 6'...

[Page 14] Heat & Glo SL-350TRSI-AUE

14 Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06 Figure 15. USE DVP-SERIES COMPONENTS ONLY. FLUEING WITH TWO (2) 90° ELBOWS V H H + H 1 1´ MIN. (0.30M) 1´ MAX. (0.30M) 2´ MAX. (0.61M) 2´ MIN. (0.61M) 2´ MAX. (0.61M) 4´...

[Page 15] Heat & Glo SL-350TRSI-AUE

15 Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06 FLUEING WITH THREE (3) 90° ELBOWS V H H + H 1 FT. (M) FT. (M) FT. (M) 2' MIN.(0.61M) 2' MAX.(0.61M) 4' MAX.(1.22M) 3...

[Page 16] Heat & Glo SL-350TRSI-AUE

16 Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06 Figure 17. FLUEING WITH THREE (3) 90° ELBOWS 1´ MIN. (0.30M) 1´ MAX. (0.30M) 3´ MAX. (0.91M) 2´ MIN. (0.61M) 2´ MAX. (0.61M) 5´ MAX. (1.52M) 3´ MIN. (0.91M) 4´ MAX. (1....

[Page 17] Heat & Glo SL-350TRSI-AUE

17 Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06 Figure 18. WARNING: FAILURE TO REMOVE INSULATION IN THE SET OF COL- LARS YOU ARE USING COULD CAUSE A FIRE. WARNING: THE REAR FLUE COL- LAR SEAL CAP MUST REMAIN AT- TACHED TO T...

[Page 18] Heat & Glo SL-350TRSI-AUE

18 Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06 ! WARNING: ENSURE THAT THE HEATER GASKET SUPPLIED WITH THE HEATER SEALS BETWEEN THE FIRST FLUE COMPO- NENT AND THE OUTER HEATER WRAP. Fire Risk Exhaust Fumes Risk Impaired Perfo...

[Page 19] Heat & Glo SL-350TRSI-AUE

19 Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06 2. Continue Adding Flue Components To continue adding flue components in accordance with the pre-planned flue system configuration: • Ensure that each succeeding flue compone...

[Page 20] Heat & Glo SL-350TRSI-AUE

20 Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06 For Vertical Runs The flue system must be supported every eight (8) feet (2.4 M) above the heater flue outlet by wall brackets. To install support brackets for vertical runs: �...

[Page 21] Heat & Glo SL-350TRSI-AUE

21 Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06 ! Figure 27. Ceiling Firestop (Ceiling Side) If the area above the ceiling IS an attic, position and secure the firestop on top of the previously framed hole. C. Flue Term...

[Page 22] Heat & Glo SL-350TRSI-AUE

22 Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06 For Vertical Terminations - To locate the flue and install the flue sections: • Locate and mark the flue centerpoint on the under- side of the roof, and drive a nail through t...

[Page 23] Heat & Glo SL-350TRSI-AUE

23 Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06 1.4 IGNITION SYSTEM WIRING • This gas heater is equipped with an electronic igni- tion system which operates on a 6 volt system. • This appliance requires 240 VAC to be wire...

[Page 24] Heat & Glo SL-350TRSI-AUE

24 Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06 Figure 32. NOTE: IF ANY OF THE ORIGINAL WIRE AS SUPPLIED WITH THE APPLIANCE MUST BE RE- PLACED, IT MUST BE REPLACED WITH TYPE 105 • C RATED WIRE. Figure 33. BROWN BROWN BLUE ...

[Page 25] Heat & Glo SL-350TRSI-AUE

25 Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06 Figure 34. 1.6 FINISHING The minimum clearance to combustibles are 0 from the sides, floor, back and top (these clearances are defined by the standoffs). The minimum distance t...

[Page 26] Heat & Glo SL-350TRSI-AUE

26 Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06 Figure 35. Figure 36. MAKE SURE THE FLAMES ARE STEADY—NOT LIFTING OR FLOATING. Installing the Trim Combustible materials may be brought up to the specified clearances on the s...

[Page 27] Heat & Glo SL-350TRSI-AUE

27 Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06 1 2 3 4 5 6 1.8 LOG PLACEMENT INSTRUCTIONS Log Set Assembly: LOGS-350CE-D Carefully remove the logs from the packaging. CAUTION: Logs are fragile! LOG #1 (SRV327-701): Place lo...

[Page 28] Heat & Glo SL-350TRSI-AUE

28 Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06 LOG #3 (SRV705-703): Rest log #3 against the right front grate corner and place its slot over the right burner tab. LOG #4 (SRV530-716): Place the left end of log #4 in the groo...

[Page 29] Heat & Glo SL-350TRSI-AUE

29 Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06 LOG #6 (SRV540-704): Place log #6 against the second and third grate bars. If sooting occurs, the logs might need to be repositioned slightly to avoid excessive flame impingeme...

[Page 30] Heat & Glo SL-350TRSI-AUE

30 Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06 ! ! OPERATING CAUTIONS • This appliance may exhibit a slight carbon deposition. • Do not place articles on or against this appliance. • Do not use or store flammable mater...

[Page 31] Heat & Glo SL-350TRSI-AUE

31 Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06 2.1 SAFETY & LIGHTING INFORMATION Follow SAFETY INFORMATION and LIGHTING IN- STRUCTIONS to light the appliance. By design, the flame pattern will not be identical from uni...

[Page 32] Heat & Glo SL-350TRSI-AUE

32 Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06 ! 2.2 FAN OPERATION The accessory fan is wired in series with a speed con- trol switch and a temperature sensor switch. Set the speed control to an "ON" position and l...

[Page 33] Heat & Glo SL-350TRSI-AUE

33 Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06 PILOT BRACKET RETAINING SCREWS 3.1 REMOVAL OF COVERS FOR SERVICING A. Control Compartment Door • Rotate the lower door down to access the gas controls. B. Dress ...

[Page 34] Heat & Glo SL-350TRSI-AUE

34 Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06 3.5 TROUBLESHOOTING SL-350TRSI-AUE With proper installation and maintenance, your new Gas Heater should provide years of trouble-free service. If you do experience a p...

[Page 35] Heat & Glo SL-350TRSI-AUE

35 Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06 (NG, LP) Exploded Parts Diagram Service Parts SL-350TRSI-AUE Beginning Manufacturing Date: 6/06 Ending Manufacturing Date: ______ 22 Log set assembly 2 13 4 10 16 15 14 12 7 8 ...

[Page 36] Heat & Glo SL-350TRSI-AUE

36 Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06 SL-350TRSI-AUE Service Parts List IMPORTANT: When ordering, supply serial and model numbers to ensure correct service parts. ITEM PARTS PART NUMBER 1 Valve NG 2098-134 Valve LP...

[Page 37] Heat & Glo SL-350TRSI-AUE

37 Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06 LIMITED 10 YEAR WARRANTY HEAT & GLO, a brand of Hearth & Home Technologies Inc. In order to presumptively establish the dates to which your HEAT & GLO Limited 10 Yea...

[Page 38] Heat & Glo SL-350TRSI-AUE

38 Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06 For Service or Replacement Parts Contact: Melbourne Jetmaster 444 Swan Street Richmond 3121 (03) 9429-5573 Perth Fireplace Corner 277 Lord Street East Perth 6000 (08) 9228-2600 ...