Humminbird Ultima Operation Manual

Download or browse on-line these Operation Manual for Humminbird Ultima Fish Finder.

Humminbird Ultima Manual Information:

This manual for Humminbird Ultima, given in the PDF format, is available for free online viewing and download without logging on. The guide contains 20 pages, and the size of the file at download is . The document type is Operation Manual.

Download Manual

Summary of Contents:

[Page 1] Humminbird Ultima

...

[Page 2] Humminbird Ultima

TRANSDUCER MOUNTING PROCEDURE Humminbird’s high-speed transducer is supplied with your LCR. This transducer has been designed to give good high speed readings on most all boat designs, including aluminum. Please carefully consider the follow...

[Page 3] Humminbird Ultima

by rotating up out of the metal spring bracket without harming the transducer, or your boat. The transducer can be re-engaged by simply rotating the transducer down and snapping it back in place. (See Figure A) B. Inside Hull Mount- The hig...

[Page 4] Humminbird Ultima

Once the location is determined mark and drill three 7/64” dia.. holes noted on the template. Attach the metal bracket using three #10 self threading screws supplied. Be sure to align holes in the center of the Bracket slots. On some alumin...

[Page 5] Humminbird Ultima

NOTE: On boats with more than 15 degree deadrise angle it may be necessary to mount the transducer slightly off parallel with the water level. (See Figure E) Mark and drill the three 9/64” dia. holes as shown on the template. Attach the met...

[Page 6] Humminbird Ultima

Step 4 TRANSDUCER ASSEMBLY- Insert the transducer assembly into the metal bracket from the bottom. Push up until the holes in the plastic pivot align with the uppermost holes in the bracket. Slide the O-ring on to the headed pin and insert i...

[Page 7] Humminbird Ultima

wrench provided. The screws are visible through the access holes on each side of the metal bracket. Check to make sure the transducer main body is rigidly fastened to the pivot. (See Figure H) Step 6 CHECK POSITION OF TRANSDUCER- At this po...

[Page 8] Humminbird Ultima

7. Remove the water and transducer and clean the marked area and the bottom of the transducer thoroughly. 8. Using the Humminbird Epoxy Kit or equivalent, mix an ample amount of epoxy without causing it to bubble and pour it in the area the tran...

[Page 9] Humminbird Ultima

Install the mounting knobs and tighten snugly. The unit can now be swiveled and tilted to any desired position. ...

[Page 10] Humminbird Ultima

OTHER MOUNTING OPTIONS 1. The LCR gimbal bracket can also be mounted on the SM-4, quick disconnect swivel mount. 2. The LCR gimbal bracket can also be mounted directly to the dash without the swivel mount, however, this metho d is not rec...

[Page 11] Humminbird Ultima

It plugs into the outlet on the back of the unit marked “Power”. The transducer connector is identified with the letter T and plugs into the outlet on the back of the unit marked “Transducer”. Note: An adapter (AD-4) is available to allow u...

[Page 12] Humminbird Ultima

INSTALLING THE ULTIMA Before mounting the Ultima, gather the parts you need; Ultima, gimbal mounting bracket, mounting hardware kit, power cable, and transducer cable. If the transducer cable is not long enough for your installation, see "...

[Page 13] Humminbird Ultima

TESTING THE INSTALLATION After installing your Ultima, transducer, and cables, you should test the installation. Testing should be performed on the water, since that is the only way to check your transducer's performance. With your b...

[Page 14] Humminbird Ultima

WHAT YOU SEE ON-SCREEN OPERATING THE ULTIMA The Ultima offers several functions that you can adjust with the front panel buttons. (Note that to select something with a button, you must press it fully so that you hear a "c...

[Page 15] Humminbird Ultima

• Display Speed • TripLog To adjust any of these, press SELECT until the function you want appears. Each function's display tells you how to use the arrow buttons and ONOFF for adjustment; when first learning, you should also refer t...

[Page 16] Humminbird Ultima

2. Setting Depth Range; Factory setting: On (Automatic) When you turn the Ultima on, it finds the bottom, sets the ideal depth range, and automatically adjusts the depth range (to as much as 185 meters) as the depth changes. In this "Au...

[Page 17] Humminbird Ultima

4. Enabling Fish Alarm; Factory setting: OFF The Fish Alarm alerts you with a chirping sound whenever the Ultima detects fish (or another object not attached to the bottom). To activate it, select FISH ALARM and press the ON-OFF button. A fish...

[Page 18] Humminbird Ultima

6. Using Bottom Lock; Factory setting; OFF Bottom Lock provides an up-close view like Zoom, except that in this case the zoomed view automatically moves up or down to stay on the bottom. To use this feature, select BOTTOM LOCK and press ON-OFF...

[Page 19] Humminbird Ultima

8. Setting Display Speed; Factory setting: Maximum The Ultima display is "updated" (advances across the screen) as you move through the water. The speed at which the display is updated depends on the Display Speed setting. To adjus...

[Page 20] Humminbird Ultima

Maintenance Your Humminbird Ultima is designed to give you years of trouble-free operation with virtually no maintenance. Follow the simple procedures below to ensure that you Ultima continues to deliver top performance: If the ...