Humminbird Wide 128 Operation Manual

Download or browse on-line these Operation Manual for Humminbird Wide 128 Fish Finder.

Humminbird Wide 128 Manual Information:

This manual for Humminbird Wide 128, given in the PDF format, is available for free online viewing and download without logging on. The guide contains 24 pages, and the size of the file at download is . The document type is Operation Manual.

Download Manual

Summary of Contents

[Page 1] Humminbird Wide 128 Manual

Page 1           ...

[Page 2] Humminbird Wide 128 Manual

Page 2   INSTALLATION PREPARATION  PARTS SUPPLIED    PARTS SUPPLIED    Before installing your new Humminbird fishfinder, please ensure the following parts are included in the box:    • ...

[Page 3] Humminbird Wide 128 Manual

Page 3 INSTALLATION PREPARATION  INSTALLATION OVERVIEW    Determining How to Mount the Transducer    Your Humminbird fishfinder includes a standard transducer. This transducer can be mounted on the tran...

[Page 4] Humminbird Wide 128 Manual

Page 4 INSTALLATION PREPARATION   ALTERNATE MOUNTING METHODS    ALTERNATE TRANSDUCERS AND MOUNTING METHODS    Your Humminbird fishfinder comes with everything necessary for installation and operation on most...

[Page 5] Humminbird Wide 128 Manual

Page 5 INSTALLATION PREPARATION  TRANSDUCER EXCHANGE    TRANSDUCER EXCHANGE  Other transducers are available as replacements for the standard transducer. You may exchange your new and unassembled transducer ...

[Page 6] Humminbird Wide 128 Manual

Page 6 INSTALLATION  TRANSOM INSTALLATION    Do not begin this transducer installation until you read the Installation Preparation in the Operation Guide. This chapter contains information critical to the correct...

[Page 7] Humminbird Wide 128 Manual

Page 7 INSTALLATION  TRANSOM INSTALLATION    •  If the propeller(s) is (are) forward of the transom, it may be impossible to find an area clear from turbulence, and a different mounting technique or transd...

[Page 8] Humminbird Wide 128 Manual

Page 8 INSTALLATION  TRANSOM INSTALLATION    Step Four - Mount the Transducer to the Transom    1.  Apply silicone sealant to the mounting holes drilled into the transom.    2. ...

[Page 9] Humminbird Wide 128 Manual

Page 9 INSTALLATION  TRANSOM INSTALLATION    Step Six - Route the Cable  There are several ways to route the transducer cable to the to the area where the control head will be installed. The most c...

[Page 10] Humminbird Wide 128 Manual

Page 10 INSTALLATION  INSIDE THE HULL INSTALLATION    INSIDE THE HULL INSTALLATION  Inside the hull installation requires the mount system and control head be installed and operational. See Installing t...

[Page 11] Humminbird Wide 128 Manual

Page 11 INSTALLATION  INSIDE THE HULL INSTALLATION    3.  Power up the Control Head.    4.  Run the boat at various speeds and water depths while observing the screen on the  Control Head...

[Page 12] Humminbird Wide 128 Manual

Page 12 INSTALLATION  CONTROL HEAD INSTALLATION    CONTROL HEAD INSTALLATION    Step One - Determine Where to Mount    Begin the installation by determining where to mount the control head. Co...

[Page 13] Humminbird Wide 128 Manual

Page 13 INSTALLATION  CONTROL HEAD INSTALLATION    and one amp fuse (not included) for the protection of the unit (Figure 21). Humminbird is not responsible for over voltage or over current failures.    In o...

[Page 14] Humminbird Wide 128 Manual

Page 14 INSTALLATION  CONTROL HEAD INSTALLATION    Step Five - Assembling the Connector Holder    1.  Insert the cable connectors into the connector holder.  The cable connectors are labe...

[Page 15] Humminbird Wide 128 Manual

Page 15 INSTALLATION  TEST THE INSTALLATION    TEST THE INSTALLATION    Testing should be performed with the boat in the water, however you can initially confirm basic operation with the boat trailered....

[Page 16] Humminbird Wide 128 Manual

Page 16 TESTING THE INSTALLATION  After installation is complete and all connections are made, you are ready to test the installation prior to actual use. Thorough testing should be performed with the boat in water, howeve...

[Page 17] Humminbird Wide 128 Manual

Page 17  SIMULATOR OPERATION  The Wide 128 contains a simulator which allows you to use the unit as if you are on the water. The Simulator is invaluable for learning how to operate the many features of the Wide 1...

[Page 18] Humminbird Wide 128 Manual

Page 18 or sand, the depiction will be thick and less dense. This indicates that much of the signal is absorbed by the soft bottom. If the bottom is rocky or rugged in composition, the depiction is of varying density and textur...

[Page 19] Humminbird Wide 128 Manual

Page 19     CONTROL FUNCTIONS    The Wide 128 uses a simple 5-button keypad for all user input. When any button is pressed, an audible "chirp" confirms the control input. In the event that a particul...

[Page 20] Humminbird Wide 128 Manual

Page 20 Once a menu times out, it is still considered the active menu. Pressing MENU will bring up the last used menu.  The UP ARROW and DOWN ARROW make adjustments to menu functions. On the left side of every menu th...

[Page 21] Humminbird Wide 128 Manual

Page 21  To adjust Sensitivity, press MENU repeatedly until the Sensitivity heading is displayed. When the Sensitivity menu appears, use the UP ARROW to increase the sensitivity bias, or the DOWN ARROW to reduce sensitivit...

[Page 22] Humminbird Wide 128 Manual

Page 22 Zoom  Zoom is similar to Depth Range in that it controls the range of information displayed in the graphics area of the display. Zoom, however, allows selection of ranges beneath the surface so any area of wat...

[Page 23] Humminbird Wide 128 Manual

Page 23 Depth Alarm     The Wide 128 contains an audible alarm to warn you of shallow water depths. The alarm is adjustable from 2' to 99' of depth. When the alarm is enabled, an aud...

[Page 24] Humminbird Wide 128 Manual

Page 24  Fish ID  The Fish ID menu controls the method used to portray fish. There are three selections available: ID Off, ID On, ID+. The factory setting is ID+. With ID Off, sonar returns are displayed as "...