Jonsered GT 2125 Operator's Manual

Download or browse on-line these Operator's Manual for Jonsered GT 2125 Brush Cutter, Trimmer.

Jonsered GT 2125 Manual Information:

This manual for Jonsered GT 2125, given in the PDF format, is available for free online viewing and download without logging on. The guide contains 32 pages, and the size of the file at download is . The document type is Operator's Manual.

Download Manual

More Manuals:

In case you failed to obtain relevant information in this document, please, look through related operating manuals and user instructions for Jonsered GT 2125. Just click one of the links below to go to the selected manual:

Summary of Contents:

[Page 1] Jonsered GT 2125

GT 2125 GC 2125 Operator’s manual (EPA) Please read the operator’s manual carefully and make sure you understand the instructions before using the machine. ...

[Page 2] Jonsered GT 2125

2 – English KEY TO SYMBOLS Symbols WARNING! Clearing saws, brushcutters and trimmers can be dangerous! Careless or incorrect use can result in serious or fatal injury to the operator or others. Please read the operator’s ma...

[Page 3] Jonsered GT 2125

English – 3 CONTENTS Contents Note the following before starting: Jonsered has a policy of continuous product development and therefore reserves the right to modify the design and appearance of products without prior notice. L...

[Page 4] Jonsered GT 2125

4 – English SAFETY INSTRUCTIONS Personal protective equipment GLOVES Gloves should be worn when necessary, e.g., when fitting cutting attachments. HEARING PROTECTION Wear hearing protection that provides adequate noise reduct...

[Page 5] Jonsered GT 2125

English – 5 SAFETY INSTRUCTIONS Vibration damping system Your machine is equipped with a vibration damping system that is designed to reduce vibration and make operation easier. Use of incorrectly wound cord or an incorrect cu...

[Page 6] Jonsered GT 2125

6 – English SAFETY INSTRUCTIONS Checking, maintaining and servicing the machine ′′ ′′ s safety equipment Throttle lock • Make sure the throttle control is locked at the idle setting when the throttle loc...

[Page 7] Jonsered GT 2125

English – 7 SAFETY INSTRUCTIONS • Regularly check that the muffler is securely attached to the machine. • If the muffler on your machine is fitted with a spark arrestor mesh then it should be cleaned regularly. A blocked m...

[Page 8] Jonsered GT 2125

8 – English SAFETY INSTRUCTIONS Cutting equipment Sharpening grass cutters and grass blades • See the cutting attachment packaging for correct sharpening instructions. • Sharpen blades and cutters using a single-cut �...

[Page 9] Jonsered GT 2125

English – 9 SAFETY INSTRUCTIONS General safety precautions Starting • The complete clutch cover and shaft must be fitted before the machine is started, otherwise the clutch can come loose and cause personal injury. • ...

[Page 10] Jonsered GT 2125

10 – English SAFETY INSTRUCTIONS • The transport guard must always be fitted to the cutting attachment when the machine is being transported or in storage. General working instructions Basic safety rules 1 Look arou...

[Page 11] Jonsered GT 2125

English – 11 SAFETY INSTRUCTIONS Grass trimming using a trimmer head and plastic blades Trimming • Hold the trimmer head just above the ground at an angle. It is the end of the cord that does the work. Let the cord work...

[Page 12] Jonsered GT 2125

12 – English WHAT IS WHAT? What is what on the trimmer? 30 1 Trimmer head 2 Grease filler cap, bevel gear 3 Bevel gear 4 Cutting attachment guard 5 Shaft 6 Loop handle 7 Throttle control 8 Stop switch 9 Throttle lock 10 Cylinder cover 11 Starter h...

[Page 13] Jonsered GT 2125

English – 13 ASSEMBLY Fitting the loop handle (GT 2125) • Position the handle on the shaft. Note that the handle must be mounted below the arrow on the shaft. • Fit the screw, securing plate and wing nut as shown in the diagram. • Tighten t...

[Page 14] Jonsered GT 2125

14 – English ASSEMBLY Fitting the trimmer guard and Auto 32 trimmer head (GC 2125) • Fit the correct trimmer guard (A) for use with the trimmer head. Hook the guard onto the fitting on the shaft and secure it with the bolt (L). • Fit the dr...

[Page 15] Jonsered GT 2125

English – 15 ASSEMBLY Fitting other guards and cutting attachments (GC 2125) • Fit the correct trimmer guard (A) for use with the trimmer head. Hook the trimmer guard/combination guard onto the fitting on the shaft and secure with the bolt (L...

[Page 16] Jonsered GT 2125

16 – English FUEL HANDLING Fuel CAUTION! The machine is equipped with a two-stroke engine and must always been run using a mixture of gasoline and two-stroke engine oil. It is important to accurately measure the amount of oil to be mixed to ensu...

[Page 17] Jonsered GT 2125

English – 17 FUEL HANDLING Fueling • Clean the area around the fuel cap. Contamination in the tank can cause operating problems. • Ensure that the fuel is well mixed by shaking the container before filling the tank. ! WARNING! Taking the fol...

[Page 18] Jonsered GT 2125

18 – English STARTING AND STOPPING Check before starting • Check that the support flange is not cracked due to fatigue or due to being tightened too much. Discard the support flange if it is cracked. • Ensure the locking nut has not lost it...

[Page 19] Jonsered GT 2125

English – 19 STARTING AND STOPPING some resistance (the starter pawls grip), now quickly and powerfully pull the cord. Never wrap the starter cord around your hand Repeat pulling the cord until the engine starts. When the engine starts. return c...

[Page 20] Jonsered GT 2125

20 – English MAINTENANCE Carburetor Your Jonsered product has been designed and manufactured to specifications that reduce harmful exhaust fumes. The engine will be run in after it has used 8-10 tanks of fuel. To ensure that the engine runs at ...

[Page 21] Jonsered GT 2125

English – 21 MAINTENANCE Fine adjustment of the idle speed T Adjust the idle speed using the idle adjustment screw T, if it is necessary to readjust. First turn the idle adjustment screw T clockwise until the cutting attachment starts to rotate. ...

[Page 22] Jonsered GT 2125

22 – English MAINTENANCE Cooling system To keep the working temperature as low as possible the machine is equipped with a cooling system. The cooling system consists of: 1 Air intake on the starter. 2 Fins on the flywheel. 3 Cooling fins on the ...

[Page 23] Jonsered GT 2125

English – 23 MAINTENANCE Spark plug The spark plug condition is influenced by: • Incorrect carburetor adjustment. • An incorrect fuel mixture (too much or incorrect type of oil). • A dirty air filter. These factors cause deposits on the sp...

[Page 24] Jonsered GT 2125

24 – English TECHNICAL DATA Technical data Note 1: Equivalent noise pressure level is calculated as the time-weighted energy total for noise pressure levels under various working conditions with the following time distribution: 1/2 idle and 1/2 ma...

[Page 25] Jonsered GT 2125

English – 25 TECHNICAL DATA Approved accessories Type Cutting attachment guard, Art. no. GT 2125 Blade shaft thread 3/8 R Trimmer head Tap-N-Go VII (R) 530 05 60-57 GC 2125 Arbor shaft thread M10 Trimmer head Trimmy H II 503 93 42-04 / 503 97 71-03...

[Page 26] Jonsered GT 2125

26 – English FEDERAL EMISSION CONTROL WARRANTY STATEMENT YOUR WARRANTY RIGHTS AND OBLIGATIONS The EPA (The US Environmental Protection Agency), Environment Canada and Jonsered are pleased to explain the emissions control system warranty on your ...

[Page 27] Jonsered GT 2125

1 Trimmy H II 2 3 4 5 6 7 8 9 7,5 m 25' 2,0-2,4 mm .080-.095" 1 2 15 cm 6" ~ 3,7 m 12' 15 cm 6" ...

[Page 28] Jonsered GT 2125

"Clic" 1 2 3 5 6 7 10 11 8,5 m 28' 4 8 4,2 m 14' 2,4-2,7 mm .095-.106" 10 cm 4" 6" 15 cm S35 ...

[Page 29] Jonsered GT 2125

1 2 4 3 2,4-2,7 mm .095-.106" 4,25 m 14' 4,25 m 14' B 6" 15 cm A 6" 15 cm S35 5 ...

[Page 30] Jonsered GT 2125

´®z*x}3¶5U¨ ´®z*x}3¶5U¨ Tap-N-Go 35 "Clic" 1 2 3 5 6 7 9 8,5 m 28' 4 8 4,3 m 14' 2,4-2,7 mm .095-.106" 10 cm 4" 6" 15 cm ...

[Page 31] Jonsered GT 2125

1 Auto 32 2 3 4 5 6 7 8 9 10 4,0 m 13' 2,4 mm .095" ~2,0 m 6,5 ' 6 " 6 " 15 cm 15 cm ...

[Page 32] Jonsered GT 2125

´®z*x}3¶5U¨ 2004-06-14 ´®z*x}3¶5U¨ 1088931-95 ...