Maytag 9700 series Installation Instructions Manual

Download or browse on-line these Installation Instructions Manual for Maytag 9700 series Dryer.

Maytag 9700 series Manual Information:

This manual for Maytag 9700 series, given in the PDF format, is available for free online viewing and download without logging on. The guide contains 13 pages, and the size of the file at download is . The document type is Installation Instructions Manual.

Download Manual

Summary of Contents:

[Page 1] Maytag 9700 series

1 DC68-02033B-03 AUTOMATIC DRYER INSTALLATION INSTRUCTIONS MISE EN SERVICE SÉCHEUSE AUTOMATIQUE INSTRUCCIONES DE INSTALACIÓN DE LA SECADORA AUTOMÁTICA The installation, including a proper exhaust system, is the responsibility of the owner. La res...

[Page 2] Maytag 9700 series

2 Note: The height of the dryer from top to floor is 38" with the leveling leg screwed all the way in. The customer can unscrew the leg out an additional 7\8" for a total overall height of 38 7/8". • Teflon tape or pipe joint compou...

[Page 3] Maytag 9700 series

3 IMPORTANT TO INSTALLER Please Read The Following Instructions Carefully Before Starting To Install The Dryer. These Instructions Should Be Retained For Future Reference. REMOVE THE DOOR FROM ALL DISCARDED APPLIANCES SUCH AS DRYERS TO AVOID THE DANG...

[Page 4] Maytag 9700 series

4 EXHAUSTING Exhausting the dryer to the outside will prevent large amounts of lint and moisture from being blown into the room. In the United States: • All dryers must be exhausted to the outside. • Only rigid or flexible metal duct should be us...

[Page 5] Maytag 9700 series

5 • Exhaust systems longer than recommended can extend drying times, affect machine operation and may collect lint. • The exhaust duct should end with an exhaust hood with a swing out damper to prevent back drafts and entry of wildlife. Never...

[Page 6] Maytag 9700 series

GAS REQUIREMENTS Use only Natural or LP (liquid propane) gases. THE INSTALLATION MUST CONFORM WITH LOCAL CODES, OR IN THE ABSENCE OF LOCAL CODES, WITH THE NATIONAL FUEL GAS CODE ANSI/Z223.1, LATEST REVISION (FOR THE UNITED STATES), OR WITH THE CAN/CG...

[Page 7] Maytag 9700 series

7 GROUNDING This dryer must be grounded. In the event of malfunction or breakdown, the ground will reduce the risk of electrical shock by providing a path of least resistance for electrical current. GAS MODELS This appliance is equipped with a cord ...

[Page 8] Maytag 9700 series

8 • If a power cord is used, the cord should be plugged into a 30-ampere receptacle. • The power cord is NOT provided with U.S. electric model dryers. IMPORTANT: When permitted by local codes, the dryer electrical supply may be connected by means...

[Page 9] Maytag 9700 series

9 INSTALLATION Parts and literature are packaged inside of dryer drum. To Install... 1. Move dryer to an appropriate location for installation. Consider installing the dryer before the washer in side-by-side installations, to allow access to gas, ele...

[Page 10] Maytag 9700 series

10 3-WIRE SYSTEM CONNECTIONS 1. Loosen or remove center terminal block screw. 2. Connect neutral wire (white or center wire) of power supply cord to the center, silver colored terminal screw of the terminal block. Tighten screw. 3. Connect the other ...

[Page 11] Maytag 9700 series

11 FINAL INSTALLATION CHECK LIST ■ Dryer is plugged into electrical outlet and is properly grounded. ■ Exhaust duct work is hooked up and joints taped. ■ Plastic flexible duct is NOT used. ■ Use rigid or stiff walled flexible metal vent mate...

[Page 12] Maytag 9700 series

12 ADDITIONAL INSTRUCTIONS FOR EXPORT MODELS (Not U.S. Mexico, or Canada) Contact the distributor that sold the appliance or: Maytag International, 1475 East Woodfield Road Schaumburg, Illinois 60173 Phone: 847-273-3100, for information on product, s...

[Page 13] Maytag 9700 series

13 1. Disconnect power supply to unit. 2. Remove 2 screws on door hinge. 3. Lift the door and remove from dryer. 4. Remove 2 screws on opposite side of door hinge. 5.Remove 2 screws on holder lever. 6. Locate door at the other side and reassemble doo...