Mitsubishi BDC4803H User Manual

[Page 1] Mitsubishi BDC4803H

Page : 1 CCD COLOR CAMERA BDC4803H USER MANUAL ...

[Page 2] Mitsubishi BDC4803H

Page : 2 CONTENTSbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb - PRECAUTIONS……………………………………… Page 3 - PACKING CONTENTS...…………………………… Page 4 - 1. User Manual……………………………...............

[Page 3] Mitsubishi BDC4803H

Page : 3 PRECAUTIONS 1. Do not attempt to disassemble the camera. There are no user serviceable parts inside. Ask a qualified service person for servicing 2. Handle the camera with care. Do not misshandle the camera. Avoid striking, shaking, etc. I...

[Page 4] Mitsubishi BDC4803H

Page : 4 PACKING CONTENTS 1. User Manual 2. Camera 3. CS-Mount Adapter 4. Auto Iris Lens Connector PACKING CONTENT S ...

[Page 5] Mitsubishi BDC4803H

Page : 5 F - Auto Light Control (ALC) function - Electronic Light Control (ELC) function - Automatic Gain Control (AGC) function - Automatic Tracing White Balance (ATW) function - Internal Synchronisation - Minimum Illumination of 1 Lux @ F2.0...

[Page 6] Mitsubishi BDC4803H

Page : 6 I 1. Power connection Connect the DC 12V powercable with the DC 12V Terminal. l Resistance of copper wire (at 20 °C) Copper wire size 0,22 mm² 0,33 mm² 0,52 mm² 0,83 mm² W / m 0,078 0,05 0,03 0,018 l Calculation of max. cable length bet...

[Page 7] Mitsubishi BDC4803H

Page : 7 2. Video cable l It is recommended to use a monitor with a resolution at least equal to that of the camera. l The max. extensible coaxial cable length between camera and the monitor is shown below. Coax cable type RG-59/U (3C-2V)...

[Page 8] Mitsubishi BDC4803H

Page : 8 3. Installation of the Auto Iris Lens Connector Install the lens connector (YFE4191J100) when using a video drive ALC lens. The installation should be made by qualified service personnel or system installers. The pin assignment of the lens c...

[Page 9] Mitsubishi BDC4803H

Page : 9 4. Mounting the Lens 1. Set up the lens by turning it clockwise on the lens mount of the camera. In case you are using a CS-Mount Lens connect the CS-Mount Adapter to the lens first and then mount it to the camera body. 2. Connect the ...

[Page 10] Mitsubishi BDC4803H

Page : 10 5. Operating controls and functions Function switch on the back (see page: 7) S/W Function ON OFF 1 BLC ON OFF 2 ALC E/S ALC 3 --- --- --- 4 AGC MIN MAX S/W 1 Back Light Compensation Mode Selector (BLC ON, OFF) Lets you select the mode acc...

[Page 11] Mitsubishi BDC4803H

Page : 11 S Model Name BDC4803H Signal Standard PAL Objective Mount C-Mount and CS-Mount (adapter) CCD – Chip 1/3” Super HAD CCD Scanning System 2:1 Interlaced Scanning Frequency H: 15.625 kHz V: 50 Hz Total Pixels 795 (H) x 596 (V) app. 4...

[Page 12] Mitsubishi BDC4803H

Page : 12 (Technical specifications subject to change. No liability will be assumed for printing errors or other errors.) A DDRES S ...