NEC SX10000 User's Manual

Download or browse on-line these Operation & User’s Manual for NEC SX10000 Projector.

NEC SX10000 Manual Information:

This manual for NEC SX10000, given in the PDF format, is available for free online viewing and download without logging on. The guide contains 56 pages, and the size of the file at download is . The document type is Operation & User’s Manual.

Download Manual

Summary of Contents:

[Page 1] NEC SX10000

SX10000 High Light Output Projection System • Großbildschirm Projektions-System User’s Manual • Bedienungshandbuch ...

[Page 2] NEC SX10000

SX10000 High Light Output Projection System User’s Manual ...

[Page 3] NEC SX10000

E – ii CAUTION: To turn off the main power, be sure to remove the plug from power outlet. The power outlet socket should be installed as near to the equipment as possible, and should be easily accessible. 3. GSGV Acoustic Noise Information Ordinanc...

[Page 4] NEC SX10000

E – iii Fire and Shock Precautions 1. Ensure that there is sufficient ventilation and that vents are unob- structed to prevent potentially dangerous concentrations of ozone and the build-up of heat inside your projector. Allow at least 8 inches (20...

[Page 5] NEC SX10000

E – iv Précautions contre l'incendie ou la décharge 1. S'assurer qu'il y ait une ventilation suffisante et que les ouvertures ne soient pas obstruées afin d'éviter des concentrations potentiellement dangereuses d'ozone ...

[Page 6] NEC SX10000

E – v LIMITATION OF IMPLIED WARRANTIES All implied warranties, including warranties of merchantability and fit- ness for a particular purpose, are limited in duration to the length of this warranty. EXCLUSION OF DAMAGES NECTECH’s liability for a...

[Page 7] NEC SX10000

E – vi TABLE OF CONTENTS Video Adj ........................................................................ E-33 Noise Reduction ...................................................... E-33 Color Matrix .................................................

[Page 8] NEC SX10000

E – 1 Getting Started The fastest way to get started is to take your time and do everything right the first time. Taking a few minutes now to review the manual may save you hours later on. At the beginning of each section of the manual you'll ...

[Page 9] NEC SX10000

E – 2 1. Part Names and Functions PC Card Slot * To turn on the main power to the projector, press the switch to the ON position (I) and the POWER indicator on the rear panel will turn or- ange in color. Press to the OFF position (0) to turn the ma...

[Page 10] NEC SX10000

E – 3 LENS SHIFT ZOOM MENU SELECT - + ENTER ON INDICATOR POWER STATUS ON/OFF OFF CANCEL FOCUS 11 10 9 8 7 5 4 2 136 1. Power Button Press to turn the projector on when the projector is in the standby con- dition (Main Power switch must be on and th...

[Page 11] NEC SX10000

E – 4 OUTPUT INPUT3 OPTION REMOTE1 RGB OUT IN REMOTE2 REMOTE3 INPUT7 INPUT8 INPUT5 INPUT6 OUT LED ON OFF IN IN Y C S-VIDEO1 S-VIDEO2 VIDEO1 VIDEO2 R/Cr B/Cb Cb H/HV VV H/HV B/Cb G/Y G/Y R/ Cr Cr SDI Y INPUT2 INPUT1 INPUT4 OUTPUT INPUT0 RGB DIGITAL ...

[Page 12] NEC SX10000

E – 5 1. INPUT 3 RGB Connector (Mini D-Sub 15 pin) Connect your PC or other analog RGB equipment such as a high-defi- nition document camera. This connector accepts RGB signals only. Not compatible with component signals. 2. Option Connector (Mini ...

[Page 13] NEC SX10000

E – 6 ENTER CANCEL UNDO AUTO HELP ON TEST ABC 1 DEF 2 GHI 3 JKL 4 MNO 5 PQR 6 STU 7 VWX 8 0 YZ/ 9 POWER INPUT OFF INFO PIXEL SOUND OSD MAGNIFY/ CTL FOCUS + - ZOOM + MENU/ ADDRESS IMAGE/ PROJECTOR POSI/ LENS KEY ST./ ON OFF R E-LIST/ PICTURE A...

[Page 14] NEC SX10000

E – 7 19 MUTE OSD Press to turn off the on-screen display. Press again to restore the on- screen display. NOTE: You can also turn off the on-screen display by pressing and holding CTL and then pressing MUTE OSD; doing this again restores it. In thi...

[Page 15] NEC SX10000

E – 8 2. INSTALLATION Formulas: Screen Width H (5:4) (m) = Screen Height V x 5/4 x 0.0254 Screen Height V (5:4) (m) = Screen Width H x 4/5 x 0.0254 Screen Diagonal (5:4) (m) = Screen Height V x 6.4/4 x 0.0254 Screen Width H (5:4) (inch) = Screen He...

[Page 16] NEC SX10000

E – 9 Lens Shift Adjustable Range Lens Shift Adjustable Range for Desktop and Ceiling Mount Application The diagram below shows the location of the image position in the lens. The lens can be shifted within the shaded area as shown using the normal...

[Page 17] NEC SX10000

E – 10 Selecting A Location The further your projector is from the screen or wall, the larger the im- age. The minimum size the image can be projected is 80" (2 m) mea- sured diagonally. The largest the image can be is 500" (12.7 m). WARN...

[Page 18] NEC SX10000

E – 11 Connecting the Power Cable and Turning on the Projector Before you turn on your projector, ensure that the computer or video source is turned on and that your lens cap is removed. 1. Connect the supplied power cable to the projector. Plug th...

[Page 19] NEC SX10000

E – 12 About Startup Screen (Menu Language Select screen) When you first turn on the projector, you will get the Startup screen. This screen gives you the opportunity to select one of the seven menu languages: English, German, French, Italian, Span...

[Page 20] NEC SX10000

E – 13 Set up the projector 1. Turn on the projector 2. Select your type of projection: Desktop front, ceiling rear, desktop rear, and ceiling front. 3. Display the test pattern by pressing the TEST button on the re- mote control or using the menu....

[Page 21] NEC SX10000

E – 14 Keystone Keystone distortion Normal Keystone is the distortion of a projected image that usually creates a wider top than bottom. Aiming a projector upward on a wall rather than straight at a wall creates this distortion. Use the 䊴 or �...

[Page 22] NEC SX10000

E – 15 3-1-6-3. Remove the PC card from the slave projector. NOTE: If you select the RGB1 input on the master projector, you must select the same input on the slave projector. The same applies to the RGB2 input. NOTE: After adjusting and registerin...

[Page 23] NEC SX10000

E – 16 Projector Orientation An image can be projected from in front or behind a screen, and the projector can be installed on the ceiling*. Ceiling Front Projection Use [Projector Options] →[Setup] →[Page 1] →[Orientation] to select "Ce...

[Page 24] NEC SX10000

E – 17 When used in standalone operation Connecting Your PC Or Macintosh Computer Connecting your PC or Macintosh computer to SX10000 Projector will enable you to project your computer's screen image for an impressive presentation. To connect ...

[Page 25] NEC SX10000

E – 18 OUTPUT INPUT3 OPTION REMOTE1 RGB OUT IN REMOTE2 REMOTE3 INPUT7 INPUT8 INPUT5 INPUT6 OUT LED ON OFF IN IN Y C S-VIDEO1 S-VIDEO2 VIDEO1 VIDEO2 R/Cr B/Cb Cb H/HV VV H/HV B/Cb G/Y G/Y R/ Cr Cr SDI Y INPUT2 INPUT1 INPUT4 OUTPUT INPUT0 RGB DIGITAL...

[Page 26] NEC SX10000

E – 19 When Used with Two or More Switchers (100 Inputs) Up to 100 inputs can be accepted using the NEC ISS-6020 Switcher. How to make connections: 1. Connect the REMOTE 1 terminal of the master Switcher to the RE- MOTE 1 of the projector using the...

[Page 27] NEC SX10000

E – 20 Set the DIP switch (S8601) of the Switcher as follows: The Projector Slot 1 of the Master Slot 2 of the Master Slot 3 of the Master Slot 4 of the Master Slot 5 of the Master Slot 6 of the Master Slot 7 of the Master Slot 8 of the Master Slot...

[Page 28] NEC SX10000

E – 21 REMOTE 1 Connector Pin Configuration of Optional CTL-6010 Cable REMOTE 1 connector of the Switcher mini D- sub 15 pin (female) REMOTE 1 connector of the Projector mini D-sub 15 pin (female) Shield (frame ground) Pins without a number are ope...

[Page 29] NEC SX10000

E – 22 When used in stand alone operation. Pin No. 14 5 10 4,8,12,11 SHORT/OPEN SHORT OPEN SHORT OPEN SHORT OPEN FUNCTION External control mode ON External control mode OFF POWER ON POWER OFF PICTURE MUTE ON PICTURE MUTE OFF * When the combinations...

[Page 30] NEC SX10000

E – 23 REMOTE2 INPUT7 S-VIDEO1 Y C IN OUT Operating Multiple Projectors with the Remote Control You can operate multiple projectors with the same remote control in wireless operation. To do so: 1. Select [Menu] → [Projector Options] → [Setup] ...

[Page 31] NEC SX10000

E – 24 Using the RGB DIGITAL connectors The Link mode function allows you to adjust or set multiple projectors using the RGB DIGITAL and OPTION connectors. The DVI DIGITAL input accepts up to the SXGA (1280 x 1024 @75Hz) signal in Link mode. NOTE: ...

[Page 32] NEC SX10000

E – 25 Using The Menus 1. Press the MENU button on the remote control to display the menu. 2. Use the ▲ or ▼ button on the remote control to select the sub menu. 3. The right-oriented delta symbol indicates further choices are avail- able. Pres...

[Page 33] NEC SX10000

E – 26 Customizing Basic/Custom Menu The Basic/Custom menu can be customized to meet your requirements. Selecting a menu item from the "Basic/Custom Menu Edit" list, allows you to custom tailor the menu items to your needs. 1. Select &quo...

[Page 34] NEC SX10000

E – 27 A List of Direct Key Combinations CTL+ INPUT (1-10) Switches to any selected signal found in the Entry List. To enable this combination, you must first assign specific remote keys for direct input selection in the Entry Edit window. CTL+ ...

[Page 35] NEC SX10000

E – 28 Menu Tree 0 – 100 NTSC, Graphics, Graphics NTSC, PAL/SECAM2.8, PAL/SECAM, Natural 1/Natural 2 Advanced Menu Source Select Adjust (Source) Ref Adj Factory Default Projector Options Help Test Pattern RGB1 RGB2 RGB3 Component (YCbCr) Video1 ...

[Page 36] NEC SX10000

E – 29 Maximum / Medium / Minimum Advanced Menu Source Select Adjust (Source) Ref Adj Factory Default Projector Options Help Test Pattern All Data / Current Signal Including Entry List Keystone Lamp Ref. White Bal. Contents Source Information Proje...

[Page 37] NEC SX10000

E – 30 Menu windows or dialog boxes typically have the following elements: Title bar: Indicates the menu title. Highlight: Indicates the selected menu or item. Solid triangle: Indicates further choices are available. A highlighted triangle indicate...

[Page 38] NEC SX10000

E – 31 Menu Descriptions & Functions Source Select Enables you to select a video source such as a VCR, DVD player, laser disc player, computer or document camera depending on what is connected to your inputs. Press the up/down buttons on your r...

[Page 39] NEC SX10000

E – 32 Picture Select "List" and press ENTER to display the direct Key assignment list. Select "OK" and press ENTER to close the window. To close the List window, press CANCEL on the remote. Adjust (Source) This option corrects ...

[Page 40] NEC SX10000

E – 33 Horizontal/Vertical Position (when Auto Adjust is off) Adjusts the image location from left to right. This adjustment is made automatically when the Auto Adjust is turned on. Aspect Ratio (not available for RGB) You can select the aspect rat...

[Page 41] NEC SX10000

E – 34 Color Matrix First, select an appropriate color matrix for your input signal, either HDTV or SDTV. Then select an appropriate matrix type from B-Y/R- Y, Cb/Cr, Pb/Pr or IVX. NOTE: The Color Matrix feature is available for component video sig...

[Page 42] NEC SX10000

E – 35 Select either the RGB signal type or the Component signal type. RGB ............. RGB signal Component .. Composite signals such as Y/Cb/Cr, Y/Pb/Pr NOTE: This feature is available on RGB 1 and 2 only. Gain This feature adjusts the input lev...

[Page 43] NEC SX10000

E – 36 Lamp Mode This feature allows the lamp power supply to operate under three set- tings. Maximum ..... This setting consumes maximum current from the AC input and results in the most light output. NOTE: The Maximum mode shortens the lamp life....

[Page 44] NEC SX10000

E – 37 5. To enable your setting, select Active on the Execute Switch. 6. Select OK and press the ENTER button on the remote control to complete the setting. NOTE: When On Timer is set and the projector is in the standby mode, the Status indicator ...

[Page 45] NEC SX10000

E – 38 Setup Enables you to set operating options. Press "OK" to save your changes for all the features of Page1, Page2, Page3, Page 4 and Page5. [Page 1] Orientation This reorients your image for your type of projection. The options are:...

[Page 46] NEC SX10000

E – 39 Power Management When this option is on and there is no RGB input for five minutes or more, the projector will automatically turn itself off. Power Off Confirmation This option determines whether a confirmation dialog for turning off the pro...

[Page 47] NEC SX10000

E – 40 Source Information Displays the status of the current signal. This dialog box has three pages. Projector Information Displays the information for your projector such as lamp usage, serial number and version number etc.. Link Mode Displaying ...

[Page 48] NEC SX10000

E – 41 Selecting a new signal that is close to one of the listed signals in horizontal and vertical frequency Selecting a new signal that is close to one of the listed signals in hori- zontal and vertical frequency may not display the image correct...

[Page 49] NEC SX10000

E – 42 6. SPECIFICATIONS Optical Panel * 1 DMD TM .9" x 3 1280 x 1024 native resolution up to 1600 x 1200 with Advanced AccuBlend TM Technology Lamp 2.0kW Bubble Type Short Arc Xenon Built in: Overheat Protection Lamp Over-Usage Protection ...

[Page 50] NEC SX10000

E – 43 External Control RS232C (1) D-sub 9 pin Contact Closure Switcher (2) D-sub 15 pin In/Out Addressable Remote Control (wired / wireless) Power Requirement 200-240 VAC, 50/60Hz Input Current 14 A Power Consumption 2.8 kW Mechanical Installation...

[Page 51] NEC SX10000

E – 44 7. Optional Accessories Lens TL-08SF (Short Focal Lens 0.84) : 10kg TL-1ZH (Zoom Lens 1.5 - 2.5:1) : 5.5kg TL-2Z (Zoom Lens 2.5 - 4.0:1) : 4.5kg TL-4Z (Zoom Lens 4.0 - 7.0:1) : 4.5kg Interface Board XT SDI BOARD SX HDSDI Board Ceiling Mount ...

[Page 52] NEC SX10000

E – 45 8. Compatible Input Signal List Compatible Input Signal List NOTE 1:The VGA, SVGA, XGA and UXGA signals are displayed with Advanced AccuBlend. NOTE 2: UXGA can be supported for separate sync signal only. NOTE 3: DVI digital signal can suppor...

[Page 53] NEC SX10000

E – 46 Function Link mode Menu Source Select L Adjust(Source) Picture Brightness L Contrast L The others N White Balance N Image Pixel Adjust L (Phase) Position L The others N Video Adj N Option Adj N Lens Memory N Signal Type N Switcher N Ref Adj ...

[Page 54] NEC SX10000

E – 47 360 (14.17) 680 (26.77) 43 (1.69) 706 (27.80) 626 (24.65) 60 8 (0.31) (2.36) 286 (11.26) 43 (1.69) 52 (2.05) 973 (38.31) 1016 (40) 1155 (45.47) 836 (32.91) The drawings do not include the lens part. Unit: mm (inch) Appendix Dimensions Lens c...

[Page 55] NEC SX10000

E – 48 Tips on Adjusting Focus for Lens Memory Function Optimum focus for lens memory function can be achieved on the projector by paying special attention in a few areas. Focus adjustment after the projector has warmed up to normal operating tempe...

[Page 56] NEC SX10000

Printed in Japan ...