Newco B-10 Operating Instruction Manual

Download or browse on-line these Operating Instructions Manual for Newco B-10 Coffee Maker.

Newco B-10 Manual Information:

This manual for Newco B-10, given in the PDF format, is available for free online viewing and download without logging on. The guide contains 28 pages, and the size of the file at download is . The document type is Operating Instructions Manual.

Download Manual

Summary of Contents:

[Page 1] Newco B-10

Bistro 10 Operating Instruction Manual Model B-10 1-800-325-7867 3650 NEW TOWN BLVD ST. CHARLES MO 63301 WWW.NEWCOCOFFEE.COM ...

[Page 2] Newco B-10

Table of Contents Introduction & Newco Product Warranty .................. 4 Machine Dimensions & Specifications ......................... 5 Machine Features........................................................... 6 Plumbing Connections......

[Page 3] Newco B-10

Warning Labels NOTICE: Read and follow all notices posted on this machine. Do not damage or destroy these notices as they are for your protection ! WARNING  DO NOT OVERLOAD CIRCUIT.  ALWAYS ELECTRICALLY GROUND THE CHASSIS OR ADAPTOR PL...

[Page 4] Newco B-10

Introduction & Newco Product Warranty INTRODUCTION This machine is intended to brew 8-12 ounce single serving of coffee and / or powdered hot drinks into a cup. This machine will also dispense hot water for allied beverage use. It is intende...

[Page 5] Newco B-10

Machine Dimensions & Specifications 120 VAC-1600W HEATER-15A USA POWER SUPPLY 120 VAC-1400W HEATER-15A CANADIAN POWER SUPPLY 1/2 GALLON TANK 8-12 OZ CUP SIZE TEMPERATURE RANGE 180-205F CHOCOLATE & LATTE INGREDIENT CABINET DRIP TRAY ...

[Page 6] Newco B-10

Machine Features • NO CALIBRATION NEEDED-PLUG & PLAY • WHIPPER RINSE BUTTON • AUTOMATIC POWDER LEVEL RESET • PRE-PROGRAMMED DRINK RECIPES • BUTTON ASSIGNMENT FOR RECIPES • INDEPENDENT POWDER HOPPER COUNTDOWN & RESET ...

[Page 7] Newco B-10

Plumber’s Installation Instructions CAUTION: Disconnect Power to machine before proceeding with plumbing installation. 1) Attach water line to water filter, rear of machine. 2) Flush water line before installing machine. Machine should be conn...

[Page 8] Newco B-10

Installation Instructions WARNING: - Read and follow installation instructions before plugging or wiring in machine to electrical circuit. Warranty will be void if machine is connected to any voltage other than that specified on the nameplate seri...

[Page 9] Newco B-10

Set up instructions for Bistro 10 Machine Fill and install ingredient hoppers with nozzles turned up, Chocolate on left and Milk on right. Make sure “button” on bottom of hopper is seated in slot in sheet metal. Slight manual rotation of the ...

[Page 10] Newco B-10

Product Installation Procedure Cont’d Fig. 4 • Remove the plastic insert from the BIB fitment as shown in Figure 4. Fig. 5 • Using finger and thumb only to prevent over-tightening, thread the BIB connector on to the BIB fitment until se...

[Page 11] Newco B-10

Product Installation Procedure Cont’d Fig. 6 • Place the product in the storage compartment as shown in Figure 6. Fig. 7 • Position the tubing as shown in Figure 7 11 ...

[Page 12] Newco B-10

Drink Selection and Keypad Display PRODUCT SELECTION BUTTON MESSAGE DISPLAY AREA SELECTION INDICATOR LIGHT PROGRAM ACCESS AND RESET BUTTON DEFAULT HOT WATER BUTTON Programming Instructions To enter int...

[Page 13] Newco B-10

Programming Instructions (Cont’d) Pressing the “COFFEE-MILD” Button will select the Mode Displayed Pressing the “LATTE” Button will scroll forward through the Select Menu Choices Pressing the “CAPPUCCINO” Button will scroll back...

[Page 14] Newco B-10

Programming-Cont’d Setup 1. Press Button to Select “Setup” 2. Press Button to Toggle display Water Temperature Setting (170-205 F) Buzzer volume 0-25 Filter Monitoring (On or Off) Filter size 500 1000 1500 5000 gallons (Only displ...

[Page 15] Newco B-10

Programming-Cont’d Assigning Recipes To buttons 1. Press Button to Select “Setup” 2. Toggle Selection to “Assign Recipes” 4. Scroll Up & Down Recipe Choices with these Two Buttons 5. Select Recipe to be Assi g ned a Button ...

[Page 16] Newco B-10

Programming-Cont’d Changing “Call For Service” Number Note: Whenever the machine detects a service problem, a description of the problem and a “Call for Service” Telephone Number Scrolls across the Display. This number can be changed d...

[Page 17] Newco B-10

Programming -Machine Calibration 3. Select “Calibration” Calibration 1. Press Button to Select “Calibration” 2. Toggle Selection to “Calibration” 4. Press Button to Toggle display Mix Bowl Calibration Value (Ounces) Left Auger Sp...

[Page 18] Newco B-10

“Right Auger Speed” (Milk), this is the right or milk product auger delivery duty cycle value, 1-10, to adjust the auger motor speed for delivering powdered product. This value should remain at 9 or 10 for the Wolfgang Puck powdered products. ...

[Page 19] Newco B-10

Programming-Changing the Drink recipes NOTE: Editing and Changing the Name of Changing the Drink recipes a “No Recipe” recipe will Create a “New” Drink for that Recipe #. 2. Scroll Up & Down Recipe Choices with these Two Buttons ...

[Page 20] Newco B-10

Daily Cleaning (See Illustrations on Pages 21-23) 1. Place empty cup in dispense area 2. Push and hold “Rinse” Button until water runs clear (Rinses Mixing bowl and Coffee Mix Chamber) Empty and remove cup 3. Rotate Tab on Whipper Base C...

[Page 21] Newco B-10

Whipper Disassembly 1 767376 WHIPPER STEAM CAP 2 767195 WHIPPER MOTOR 3 767196 BASE, WHIPPER MOUNTING 4 767197 WHIPPER IMPELLER 5 767365 WHIPPER BOWL 6 767200 WHIPPER NOZZLE 7 781566 WHIPPER SEAL (REPLACE AFTER 2500 CYCLES) 2 3 4 5 6 ...

[Page 22] Newco B-10

Cleaning & Sanitizing Instructions Fig. 2 Fig. 1 1. Remove product from storage area and disconnect BIB connectors as shown in figures 1 & 2. 22 ...

[Page 23] Newco B-10

Cleaning & Sanitizing Instructions-Cont’d Fig. 3 2. Place an empty container in the dispense area of the machine as shown in figure 3. 23 ...

[Page 24] Newco B-10

Cleaning & Sanitizing Instructions-Cont’d Fig. 4 Fig. 5 3. Connect the sanitizing solution adaptor (PN 120513) to the BIB connector for Pump and connect sanitizing BIB (PN 120509) as shown in figures 4 & 5. 24 ...

[Page 25] Newco B-10

Daily Sanitizing Instructions 1. Remove the product BIBs from the machine and connect a BIB of sanitizing solution to the PUMP BIB connector as shown in figs. 1-4 pages 21-23 2. Enter “Sanitation Mode” by pressing and holding “Newco �...

[Page 26] Newco B-10

Weekly Cleaning Instructions 1. Following daily cleaning instructions above page 24 2. Remove the bag connector from the product box and disassemble or prop open the internal valve to allow free flow of product through the connector. NOTE: Cutt...

[Page 27] Newco B-10

Service Notes This machine uses advanced diagnostics to alert the operator should any of the motors or motor controllers sense the motors are not turning at the correct rate or sense a bad connection. These errors highlighted by a scrolling disp...

[Page 28] Newco B-10

28 Wiring Diagram ...