ITech IT6322 User Manual

[Page 1] ITech IT6322

Copyright 2009 All Rights Reserved Ver2.0/Oct, 2009/ IT6300-508 USER’S GUIDE Programmable DC Power Supply Model IT6322 ...

[Page 2] ITech IT6322

2 USER’S GUIDE Chapter1 Quick Start ················································································· 1.1 Front Panel &...

[Page 3] ITech IT6322

USER’S GUIDE 3 IT6322 Programmable DC Power Supplies General information The following safety precautions should be observed before using this product and any associated instrumentations. Although some instruments and accessories would ...

[Page 4] ITech IT6322

4 USER’S GUIDE About your safety The following general safety precautions must be observed during all phases of operation ofthis instrument. Failure to comply with these precautions or with specific warnings elsewhere in this man...

[Page 5] ITech IT6322

Introduction IT6300 3 channels power supply has high accuracy and high stability, also has the function of the limit voltage, over current and over temperature protection. You can set the voltage and value of from 0V to the max value in every chann...

[Page 6] ITech IT6322

1.1 Front Panel & Rear Panel Cooling window DB9 interface connector 110V/220V Power switch Fuse Power socket Rear Panel 1 2 3 4 5 VFD display Rotary knob Power switch Number keys and “Esc” key Function key UP, Down key and “Ent...

[Page 7] ITech IT6322

1.2 Preliminary Checkout The following steps help you verify that the power supply is ready for use. 1. Check the list of supplied items Verify that you have received the following items with your power supply. If anything is missing, conta...

[Page 8] ITech IT6322

If the calibration data in EEPROM was error or tthe information calibrated by factory was lost, the VFD will display as follows: 10.000V 11.000V 3.000V 2.000A 3 .000A 3 .000A Lost Factory Calibration 0.000V ...

[Page 9] ITech IT6322

1) Turn on the power supply. 2) Disable the output. Press key to ensure that the output is disabled. The ON annunciator is turned off. 3) Connect a short across (+) and (-) output terminals with an insulated te...

[Page 10] ITech IT6322

The line voltage is set to the proper value for your country (110VAC or 220VAC) when the power supply is shipped from the factory. Change the voltage setting if it’s not correct. 3). Verify that the correct power-line fuse is installed. If th...

[Page 11] ITech IT6322

7. To Rack Mount the Instrument You can mount the power supply in a standard 19-inch rack cabinet using the IT-E151 rack mount kit. Note: Remove the carrying handle and the two plastic ears before rack-mounting the instrument. To remove the handle...

[Page 12] ITech IT6322

Chapter 2 Specifications 2.1 Specifications Paramete IT6322 Output ratings ( 0 °C - 40 °C) Voltage 0~30V×2, 0~5V×1 Current 0~3A×2, 0~3A×1 LVP 0~31V×2, 0~6V×1 The model of remote sense ±(%of output+offset) Voltage ≤0.01%+3mV Current ≤...

[Page 13] ITech IT6322

State Storage Memory 9 user-congurable stored states Recommended Calibration Interval 1 year AC Input Ratings (selectable via switch on the rear panel) Option Opt.01: 220AV±10%, 47 - 63HZ Option Opt.02: 110AV±10%, 47 - 63HZ Maximum input power...

[Page 14] ITech IT6322

3.1 Front-panel Operation Overview The following section describes an overview of the front-panel keys before operating your power supply. Chapter 3 Front-panel Operation So far you have learned how to install your power supply and do quick start. D...

[Page 15] ITech IT6322

3.2 Panel Description 0~9 Number key(1~3key can control the output state of 3channels, 4~6key can set voltage value for the channel, 7~9 can set current value for the channel.) Set voltage value Set current value Save the currently data of th...

[Page 16] ITech IT6322

3.4 Menu Descriptions Press to indicate operation mode. View the menu in VFD, and use or knob to scroll through the complete menu list as following. If press , you could get the selected menu function, press ...

[Page 17] ITech IT6322

3.5 Panel Operation Exit System Set… Out Series Set Set series connection Out Parallel Set Set parallel connection Max Voltage Set… Set max voltage for each channel Set First Channel Set Second Channel Set Third Channel Out Time Set… Set output...

[Page 18] ITech IT6322

When the power supply is in panel operation, you can press to control the output state of all channels. Or you can press one number key( , , )to control one channel’ output state. Key controls the output state of the �...

[Page 19] ITech IT6322

When the knob function is disabled: Solution 1: Press +numeric key to set voltage value, press to change the value slightly, press to conrm. Solution 2: Press one number key which can contro...

[Page 20] ITech IT6322

3.6 Menu Function ■ Saving and Recalling Operation You can store up to 50 different output states in storage register locations (1 to 9). Each output state includes Constant voltage value, Constant current value and Maximum output voltage...

[Page 21] ITech IT6322

Reset Config If you enter into this menu and select “YES”, all of parameter will be as default setting. Out Parameter Set This function can decide to save the parameter or not. If you select “Last Set”, the power supply will save the output ...

[Page 22] ITech IT6322

Local Address This instruction can set the communication address for each power supply. The address range is from 0 to 31. Before the communication, you must make sure that there is same address between the power supply and the computer. ...

[Page 23] ITech IT6322

Out Parallel Set This function can set parallel connection. No means that the power supply is not in parallel connection, 1+2 means that channel 1 and channel 2 are in parallel connection, 1+3 means that channel1 ...

[Page 24] ITech IT6322

Soft Version: the version number of power supply For example: Soft Version=1.00 Cal information: calibration information of power supply For example: 2005-8-26 17:46:13 Error Information: error information of power supply For example: 0, No Error...

[Page 25] ITech IT6322

4.1 Communication cable Chapter 4 Remote Operation Mode The DB9 interface connector on the rear panel of the power supply can be transferred to RS-232 interface, the following information will tell you how to use the computer to control the output ...

[Page 26] ITech IT6322

IT-E135 GPIB Communication Cable The DB9 interface connector on the rear panel of power supply is TTL voltage level; you can use the GPIB communication cable (IT-E135) to connect the DB9 interface connector of the power supply, and then connect the...

[Page 27] ITech IT6322

4.2 Communication between Power Supply and PC Before using the remote operation mode, please make sure that the baud rate and communication address in power supply are the same as in the computer software, otherwise, the communication will fail, yo...

[Page 28] ITech IT6322

China Tel : 025-52415098 Fax: 025-52415268 3 1 0 # N i n g N a n D a D a o , NanJing City, 210012, Jiangsu Province,China Europe Tel : 477-590101 Fax: 477-572323 32, rue Edouard Martel 42100 - St Etienne France South Korea...