Endless Pools Pools Installation Instructions Manual

Download or browse on-line these Installation Instructions Manual for Endless Pools Pools Swimming Pool.

Endless Pools Pools Manual Information:

This manual for Endless Pools Pools, given in the PDF format, is available for free online viewing and download without logging on. The guide contains 24 pages, and the size of the file at download is . The document type is Installation Instructions Manual.

Download Manual

Summary of Contents:

[Page 1] Endless Pools Pools

Fully Aboveground Installations Partially In-Ground Installations Fully In-Ground Installations INSTALLATION INSTRUCTIONS ...

[Page 2] Endless Pools Pools

2 Endless Pools, Inc. provides for every aspect of an Endless Pool ® project. This manual, “Installation Instructions” assists in the installation process. This manual should be used in conjunction with other available resources including the In...

[Page 3] Endless Pools Pools

1. Pool Arrival and Inspection The Standard Endless Pool ® arrives in three packages: a skid of 6 pool panels weighing approximately 850 lbs., a 4' x 8' x 4' high crate weighing about 1,150 lbs and a pair of 6 5 /8" wide steel re...

[Page 4] Endless Pools Pools

(1) 7', 8', 9', or 10' LONG ACCESS PANEL NOTE: 1. ALL PANELS ARE 14 GAUGE STEEL WITH A 2 1 /2 OUNCE (G235 CULVERT STOCK) GALVANIZED COATING. (4) 6', 7', or 8' LONG PLAIN PANELS (2) REINFORCING CHANNELS 11 GAUG...

[Page 5] Endless Pools Pools

top 24" of the pool panel for access both during and after installa- tion. Only 8" of clearance is required for the bottom 18" of the front panel and 7" of clearance is required for the other 3 sides of the pool — disregarding f...

[Page 6] Endless Pools Pools

If the pool is to be positioned next to a wall some bolts will be hard to reach. In this case, one side may be bolted together first and then slid back against the wall. You will probably want to use blocking angle rather than anchor bolts for this i...

[Page 7] Endless Pools Pools

remaining pool walls with rigid foam insulation. See Figure 4.9 and 4.10. We would strongly recommend insulating the walls of the pool. Please note that the insulation boards should not be used under the pool as the anchoring system will be compro- m...

[Page 8] Endless Pools Pools

6.Assembly of Pool Panels with a Deeper Pool When the deeper pool option has been selected, tension straps cannot be used. The anchor bolts provided with every kit must be used for these installations. They secure the panels to the concrete through t...

[Page 9] Endless Pools Pools

any questions regarding these channels or their placement, please call Customer Service. When possible, the walls of an Endless Pool ® should be braced laterally before filling with water to reduce outward deflection when the pool is filled with wat...

[Page 10] Endless Pools Pools

of the channels to keep the whole system level. See Figure 8.3. At the 4 corners, the short mitered pieces of liner hanger rest on 4 triangular inside corner supports. Once the entire system is laid out satisfactorily secure it down to the top flange...

[Page 11] Endless Pools Pools

Retain the knob, and after mounting your coping reattach with the 1/8" allen wrench provided. Retain these 2 allen wrenches for future use. Note: Endless Pools, Inc. has pro- vided a shaft long enough for most coping systems. The installer shoul...

[Page 12] Endless Pools Pools

the specific pool size ordered. Included in the kit are radius cor- ners and straight pieces to provide a finished look. These extru- sions are fastened down to the top flange of the pool panels through the spacer washers and the reinforcing channels...

[Page 13] Endless Pools Pools

Typically the cover rolls off the rear of the pool as shown in the video. Other alternatives are possible if space is limited. These are discussed in more detail in Tech Bulletin #5. The kit includes the roller mechanism for the width of pool purcha...

[Page 14] Endless Pools Pools

before installing the liner. See Figure 18.2. The hole for suction from the pool for the jets should be cut 4" below the three inline thru-walls on the front panel. If the pool is located outdoors where freezing is an issue, care must be taken w...

[Page 15] Endless Pools Pools

Depth Stair allows the user to gradually enter the water from deck height. The steps do not obstruct the swim current. The Full Depth Stair takes the swimmer down to the bottom of the stainless steel benches. If an optional deeper pool has been selec...

[Page 16] Endless Pools Pools

28. Optional Deeper Platform Sometimes customers desire a deeper pool completely above- ground without excavation. This can be done by constructing a wooden platform using a drawing supplied by Endless Pools, Inc. This system is described in Tech Bul...

[Page 17] Endless Pools Pools

Spread the liner in the pool enclosure. See Figure 31.3. Shoes should be removed for this and all future work in the pool to avoid damaging the liner. Find the vertical seam in the liner and center it at the front of the pool as described in the vide...

[Page 18] Endless Pools Pools

assembly into the front of the pool as shown on the video taking care to keep the hose ends from getting wet. Two people can accomplish this if they work carefully in stages. Be careful not to catch the liner. Carefully slide the assembly all the way...

[Page 19] Endless Pools Pools

Each of the thru-wall fittings has two rubber washers and one cork gasket. One rubber washer is placed between the liner and the steel wall of the pool. See Figure 33.4. One rubber washer is placed between the fitting and the liner inside the pool. S...

[Page 20] Endless Pools Pools

done with the previous thru-wall fittings. See Figure 33.9. Hand tighten the large hex nut and connect the hydraulic elbow fit- tings to the top of the valve assembly as shown in the drawing accompanying the valve assembly. See Figures 33.10 and 33.1...

[Page 21] Endless Pools Pools

34. Plumbing the Pool and Water Quality System Plumb the front panel suction and return lines as described in Tech Bulletin #16. All of the plumbing fittings and the glue and cleaner to accomplish this work are packed in a cardboard box labeled Plu...

[Page 22] Endless Pools Pools

over-tighten plastic fittings as they will crack. Please note: Endless Pools, Inc. provides Teflon sealant as a convenience. If Teflon tape is preferred, please feel free to use that material. Either material will work. The Water Quality System Compo...

[Page 23] Endless Pools Pools

38.2. These hoses, described more fully in Tech Bulletin #24, are supplied by Endless Pools, Inc. to the length specified. Often they are not shipped with the pool as the exact length is unknown at the time of shipment. Please order these hoses a wee...

[Page 24] Endless Pools Pools

Endless Pools, Inc. • 200 E. Dutton Mill Rd • Aston, PA 19014-2931 800-910-2714 • 610-497-8693 fax • www.myendlesspool.com B10 10-06 Introductory Material Swim at Home A color brochure introducing what the Endless Pool is and how it can be in...