Metrologic MS860 Installation And User Manual

Download or browse on-line these Installation And User Manual for Metrologic MS860 Scanner.

Metrologic MS860 Manual Information:

This manual for Metrologic MS860, given in the PDF format, is available for free online viewing and download without logging on. The guide contains 55 pages, and the size of the file at download is . The document type is Installation And User Manual.

Download Manual

Summary of Contents:

[Page 1] Metrologic MS860

METROLOGIC INSTRUMENTS, INC. MS860i Mini-Slot™ Laser Bar Code Scanner Installation and User’s Guide MLPN 2202 Printed in USA January 1999 ...

[Page 2] Metrologic MS860

ii Locations: USA Corporate Headquarters Europe Metrologic Instruments, Inc. Metrologic Instruments GmbH 90 Coles Road Dornierstrasse 2 Blackwood, NJ 08012 82178 Puchheim b. Customer Service: 1-800-ID-METRO Munich, Germany Tel: 609-228-8100 Tel: 4...

[Page 3] Metrologic MS860

iii Table of Contents Introduction .................................................. 1 Unpacking List ................................................. 2 Scanner Connections to the Host ................................... 3 Configuration of the Sc...

[Page 4] Metrologic MS860

iv Maintenance .................................................. 25 Applications and Protocols ..................................... 25 Appendix A Specifications ...................................... 26, 27 Appendix B Default Settings ..............

[Page 5] Metrologic MS860

1 Introduction Metrologic's MS860i Mini-Slot™ Laser Bar Code Scanner is a high-speed, aggressive in-counter scanner. The MS860i unsurpassed scanning accuracy and incorporates the most advanced laser technology in a smaller, yet rugged and dur...

[Page 6] Metrologic MS860

2 Unpacking List The shipping carton contains the following: ! Installation and User’s Guide (MLPN: 2202) ScanSelect™ Scanner Programming Guide (MLPN: 2186) Volume Control Card (MLPN: 2346) ! MS860i Laser Bar Code Projection Scanner ! Installatio...

[Page 7] Metrologic MS860

3 Scanner Connections to the Host To maintain compliance with applicable standards, all circuits connected to the scanner must meet the requirements for SELV (Safety Extra Low Voltage) according to EN 60950. To avoid potential problems, do not power ...

[Page 8] Metrologic MS860

4 Configuration of the Scanner to the Host System The scanner is shipped from the factory programmed to a set of default conditions noted in the Default Settings section of this guide and in the ScanSelect™ Scanner Programming Guide. The default se...

[Page 9] Metrologic MS860

5 Cloning Feature To program several scanners with the same settings, use the Cloning feature. This is done by connecting the cloning cable (MLPN: #51544) between two scanners. 1. Turn off both scanners. 2. Connect the cloning cable between the two ...

[Page 10] Metrologic MS860

6 Version 11 IBM 46XX Scanner Output Format: IBM RS-485 serial input/output for the 4680 and 4690 (46XX) point-of-sale terminals The Version 11 46XX interface can be used in several different ways. Both the 46XX terminal and the scanner must be confi...

[Page 11] Metrologic MS860

7 Configuring the MS860i-11 Scanner Located in the Version 11 scanner are two computer boards. One computer board is for decoding and the other for 46XX IO processing. The decode board is configured using ScanSet™ or ScanSelect™ while the IO boar...

[Page 12] Metrologic MS860

8 Configuring the IBM 46XX The 4683 and 4693 terminals are configured on the store controller. The 4684 and 4694 terminals are typically configured on the individual terminals. Follow the appropriate guide for your type of equipment. IBM 4683 and 469...

[Page 13] Metrologic MS860

9 Version 17 Keyboard Wedge Scanner The MS860i scanner (version 17) provides keyboard emulation by converting the scanned bar code data to the PC keyboard scan code equivalent. The following are the supported keyboard and country types: PC Type ! AT ...

[Page 14] Metrologic MS860

10 Figure 1 Connection of a MS860i-17 Scanner to a PC To maintain compliance with applicable standards, all circuits connected to the scanner must meet the requirements for SELV (Safety Extra Low Voltage) according to EN 60950. 1. Attach the adaptor ...

[Page 15] Metrologic MS860

11 Installing the Scanner into a Counter Metrologic has designed three plates to accommodate in-counter installation of the scanner. Included automatically with the purchase of the scanner is Metrologic part #45471, Installation Plate. The universal ...

[Page 16] Metrologic MS860

12 Figure 2 Figure 3 Figure 4 Attaching the Vertical Stand to the Work Surface With the Metrologic stand (Part #45472), there is a choice of four directions the scanner can be positioned for the scanner for greater flexibility. Figure 2 illustrates ...

[Page 17] Metrologic MS860

13 Figure 5 MS860i Features Becoming familiar with the features of the MS860i will help when operating the scanner. The following illustration and list explain the pertinent parts. 1 Touch Plate When a specified time has elapsed without any scanning...

[Page 18] Metrologic MS860

14 Touch Plate The scanner will enter “standby” when it remains dormant for a time. When the scanner’s computer is on “standby," touching the touch plate will “wake up” the scanner and activate the laser. When the green LED comes on,...

[Page 19] Metrologic MS860

15 Piastra sensore Se lo scanner è rimasto disattivato per un determinato periodo esso passa in modalità 'stand-by'. Quando il calcolatore dello scanner si trova in modalità 'stand-by', occorre toccare la piastra sensore per &q...

[Page 20] Metrologic MS860

16 Visual Indicators There is a red and green LED at the top of the scanner. When the scanner is on, the flashing or stationary activity of the LEDs indicates the status of the scan and scanner. Steady Green When the laser is on, the green LED is als...

[Page 21] Metrologic MS860

17 Signaux optiques Sur la partie supérieure du scanner se trouvent une diode LED rouge et une diode LED verte. Quand le scanner est sous tension, les diodes rouge et verte clignotantes ou allumées vous informent sur l'état du scanner. Ni la ...

[Page 22] Metrologic MS860

18 Optische Anzeigen Auf dem Scanner befinden sich eine rote und eine grüne Leuchtdiodenanzeige. Bei eingeschaltetem Scanner geben Ihnen die blinkenden oder feststehenden Leuchtdiodenanzeigen Aufschluß über den Abtast- und Scannerstatus. Weder rot...

[Page 23] Metrologic MS860

19 Segnali ottici Sullo scanner si trovano due diodi luminosi: uno rosso e uno verde. Quando lo scanner è inserito, i diodi luminosi, che possono o essere accesi in continuazione o lampeggiare, Vi informano sullo stato della scansione e dell’appar...

[Page 24] Metrologic MS860

20 Volume Settings There are four volume settings available: low, medium, high and no volume. The operator can temporarily change the volume of the scanner by scanning the bar codes on the volume control card. To change the volume of the scanner per...

[Page 25] Metrologic MS860

21 Labels There is one label located inside the window of the scanner noting that the device is a CDRH Class IIa laser product and IEC 825 LASERKLASSE 1. Also, on each scanner is a label located on the back of the unit. This label contains informatio...

[Page 26] Metrologic MS860

22 Depth of Field Through the glass at the front of the scanner, safe, low powered laser beams are projected in a complex pattern that resembles a spider web. Each of the five scan fields that generate the scan pattern extends to a range of 127mm (5....

[Page 27] Metrologic MS860

23 Depth of Field and Symbol Specification (See Figure 7) Code Type Minimum Small Code Density Depth of Field Element Mil. (1/1000") UPC/EAN 10.4 80% 0" - 5" UPC/EAN 13.0 100% 0" - 6.5" Code 39 7.5 High 0" - 3" Code...

[Page 28] Metrologic MS860

24 Figure 7 ...

[Page 29] Metrologic MS860

25 Maintenance Smudges and dirt can interfere with the proper scanning of a bar code. Therefore, the output window will need occasional cleaning. 1. Spray glass cleaner onto lint free, non-abrasive cleaning cloth. 2. Gently wipe the scanner window. A...

[Page 30] Metrologic MS860

26 Appendix A Specifications Application: In-Counter Laser Bar Code Scanner Light Source: VLD 675 ± 5 nm, Maximum output 1mW CDRH: CLASS IIa laser product IEC: Class 1 laser product, EN 60825/09.91 UL/CSA/TUV: UL Listed, UL 114; CSA certified, C22.2...

[Page 31] Metrologic MS860

27 Operational Depth of Field: 0.0mm - 127mm (0" - 5") Minimum Bar Width: 0.075 inches Scan Speed: 2000 scan lines per second Scan Pattern: 5 scan fields: 1 horizontal, 4 at angles Exit Angle: 70E Indicators: LED: green=laser on; red=good r...

[Page 32] Metrologic MS860

28 Appendix B Default Settings The scanner is shipped from the factory programmed to a set of default conditions. The default parameter of the scanner has an asterisk ( * ) in the charts on the following pages. If an asterisk is not in the default co...

[Page 33] Metrologic MS860

29 Parameter Default OCIA IBM Key RS- Parallel Light 46XX Wedge 232* Pen MSI Plessey 10/10 T T T T T Check Digit MSI Plessey * T T T T T MOD 10 Check Digit UK Plessey T T T T Airline 2 of 5 T T T T Telepen T T T T MECCA T T T T T T Paraf Support T T ...

[Page 34] Metrologic MS860

30 Parameter Default OCIA IBM Key RS- Parallel Light 46XX Wedge 232* Pen Bars High as * T Code 39 Spaces High as T Code 39 Bars High as T Scanned Spaces High as T Scanned DTS/SIEMENS T DTS/NIXDORF * T NCR F T NCR S T Poll Light Pen T Source Light Pen...

[Page 35] Metrologic MS860

31 Parameter Default OCIA IBM Key RS- Parallel Light 46XX Wedge 232* Pen Beep/Transmit Before T T T T T T Sequence Communication None T T T T T T Timeout Razzberry Tone T T T T T T on Timeout Three Beeps on T T T T T T Timeout No Beeps on T T T T T T...

[Page 36] Metrologic MS860

32 Parameter Default OCIA IBM Key RS- Parallel Light 46XX Wedge 232* Pen Scanability Off T Scan Count Mode Off T Normal Depth of * T T T T T T Field Intercharacter 1 msec T T T T Delay Scan Buffer 1 T T T T T T Transmit UPC-A * T T T T T Check Digit ...

[Page 37] Metrologic MS860

33 Parameter Default OCIA IBM Key RS- Parallel Light 46XX Wedge 232* Pen Transmit Mod 43 T T T T Check Digit on Code 39 Transmit Code 39 T T T T Stop/Start Characters Transmit Mod T T T T 10/ITF Transmit Code 11 T T T T T Check Digit Transmit MSI T ...

[Page 38] Metrologic MS860

34 Parameter Default OCIA IBM Key RS- Parallel Light 46XX Wedge 232* Pen UPC Prefix T T UPC Suffix T T STX Prefix T T ETX Suffix T T Carriage Return * T T Line Feed * T T Tab Prefix T T Tab Suffix T T "DE" Disable T Command "FL"...

[Page 39] Metrologic MS860

35 Parameter Default OCIA IBM Key RS- Parallel Light 46XX Wedge 232* Pen Keyboard Type AT T Caps Lock T Alt Mode T Inter Scan Code 800 T Delay Fsec Transmit F0H * T Break Code (AT and PS/2 keyboards) Special Software is required for the following: Tw...

[Page 40] Metrologic MS860

36 Appendix C Pin Assignments Version “1” Pin Assignments for RS-232, OCIA and Light Pen Emulation The version “1” scanner head cable is terminated with a male 25-pin D-type connector. Connecting the scanner to the host device, may require a ...

[Page 41] Metrologic MS860

37 Version “2” Pin Assignments for Parallel Communication The version “2” scanner head cable is terminated with a male 25-pin D-type connector. Connecting the scanner to the host device, may require a communication cable. The communication ca...

[Page 42] Metrologic MS860

38 Version “11” Pin Assignments for RS-485 The version “11” scanner head cable is terminated with a male 25-pin D-type connector. Connecting the scanner to the host device, may require a communication cable. The communication cable may inclu...

[Page 43] Metrologic MS860

39 Version “17” Pin Assignments for Keyboard Wedge, RS-232 and Light Pen Emulation The version “17” scanner head cable is terminated with a male 25-pin D-type connector. Connecting the scanner to a PC, requires a communication cable and a tra...

[Page 44] Metrologic MS860

40 Version “3” Pin Assignments for Multi-drop RS-422 The version “3” scanner head cable is terminated with a male 25-pin D-type connector. Connecting the scanner to the host device, may require a communication cable. The communication cable ...

[Page 45] Metrologic MS860

41 Version “26" Pin Assignments for RS-422 The version “26" scanner head cable is terminated with a male 25-pin D-type connector. Connecting the scanner to the host device, may require a communication cable. The communication cable may...

[Page 46] Metrologic MS860

42 Appendix D Warranty and Disclaimer Limited Warranty Products manufactured by Metrologic have a 2-year limited warranty from date of manufacture. This warranty is limited to repair, replacement or refund at Metrologic’s discretion. Faulty equipme...

[Page 47] Metrologic MS860

43 Disclaimer Metrologic Instruments, Inc. and the author or authors make no claims or warranties with respect to the contents or accuracy of this publication, or the product it describes, including any warranties of fitness or merchantability for a ...

[Page 48] Metrologic MS860

44 Appendix E Notices Notice This equipment has been tested and found to comply with limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference wh...

[Page 49] Metrologic MS860

45 Anmerkung Nach Überprüfung dieses Geräts wurde festgestellt, daß es den Grenzwerten für Digitalgeräte der Klasse A gemäß Teil 15 der Richtlinien der US-amerikanischen Bundesbehörde für das Fernmeldewesen entspricht. Diese Grenzwerte wurd...

[Page 50] Metrologic MS860

46 Appendix F Patents “Patent Information This METROLOGIC product may be covered by one or more of the following U.S. Patents: U.S. Patent No. 4,360,798; 4,369,361; 4,387,297; 4,460,120; 4,496,831; 4,593,186; 4,607,156; 4,673,805; 4,736,095; 4,7...

[Page 51] Metrologic MS860

47 Volume Control Card ...

[Page 52] Metrologic MS860

48 ...

[Page 53] Metrologic MS860

49 Index A AC input/outlet 3, 10 Adaptor 7, 10 cable 6, 39 Application 26 Application and protocols 25 Asia ii Electrical 26 Assignments Email ii pin 36-41 Environmental 27 Attaching stand 12 ESD 27 B External Power supply 6 Bar codes 1, 4, 5, 9, 13...

[Page 54] Metrologic MS860

50 L R Labels 21 Red LED 13, 16, 27 LASERKLASSE 1 21 Repair 42 LEDs 3, 10, 13, 14, 16-19, 27 Rights Light levels 27 property 46 Light pen emulation 1, 9, 25, warranty 42 27, 36, 39 RMA 42 Light source 26 Roll, pitch, yaw 27 Limited warranty 42 RS-232...

[Page 55] Metrologic MS860

51 Version identifiers 25 Vertical stand 2, 12 Voltage 3, 10, 27 Volume control card 47, 48 W Warranty 42 Watt(s) 26 Weight 26 Window 1, 13, 21, 22, 25-27 ...