Lumel DZ2 User Manual

[Page 1] Lumel DZ2

1 USER’S MANUAL LARGE SIZE DIGITAL CLOCKS DZ2 AND DZ3 TYPES ...

[Page 2] Lumel DZ2

2 ...

[Page 3] Lumel DZ2

3 Contents 1. APPLICATIONS ......................................................................................................... 5 2. CLOCK SET .....................................................................................................

[Page 4] Lumel DZ2

4 ...

[Page 5] Lumel DZ2

5 1. APPLICATIONS The DZ digital clock shows the date and time alternately. The quantity switching over is set arbitrarily. The default value is equal 5 seconds. These digital clocks are intended to be installed outside and inside shops, by product...

[Page 6] Lumel DZ2

6 Remarks concerning the operator safety: 1. General n The digital clock is destined to be installed inside or outside buildings. n Non-authorized removal of the required housing, inappropriate use, incorrect installation or opera- tion create the r...

[Page 7] Lumel DZ2

7 6. Maintenance and servicing n Please observe the manufacturer’s documentation. n Read all product-specific safety and application notes in this user’s manual. n Before taking the digital clock housing out, one must turn the supply off. n The ...

[Page 8] Lumel DZ2

8 Dimensions DZ2 DZ3 L 1510 2020 h 284 360 Fig. 2. Overall dimensions of DZ2 and DZ3 digital clocks and layout of holes and suspension clamps 5. WIRING CONNECTIONS The clock set includes two female cable connectors: a 3-pole supplying connector and ...

[Page 9] Lumel DZ2

9 Table 1 Fig. 4. Description of sockets to connect the supplying network and interface Wires: maximal wire cross-section: 1.5 mm 2 maximal cable diameter: 4.5... 7 mm A shielded double spiral wire is recommended to connect the interface Connect the ...

[Page 10] Lumel DZ2

10 4009 RW 0...2359 Starting hour in the day expressed as: GG*100 + MM 4010 RW 0...2359 Starting hour in the day expressed as: GG*100 + MM 4011 RW 5..60 Display time of time/date before switching over. Controller status 4037 RW 0x00...0xFFFF Control...

[Page 11] Lumel DZ2

11 7. TECHNICAL DATA Power consumption max 45 W Readout field: - DZ2 10 characters of 200 mm high; 8 digits + 2 special characters (colon, hyphen, comma) digit colour: red, yellow, green, - DZ3 10 characters of 300 mm high; 8 digits + 2 s...

[Page 12] Lumel DZ2

12 8. ORDERING CODES ORDERING EXAMPLE Code: DZ 2 - R 00 means: DZ2 – digital clock with digits of 200 mm high, R – digit colour on display: red, 00 – standard version DIGITAL CLOCK DZ X- X XX Digit height: 200 mm ............................

[Page 13] Lumel DZ2

13 Table 2 9. BEFORE A FAILURE WILL BE DECLARED In case of incorect symptoms, please to get acquinted with the table below. SYMPTOMS PROCEDURE 1. Messages are not displayed Check the connection of the network cable 2. flashing of diode point on the l...

[Page 14] Lumel DZ2

14 ...

[Page 15] Lumel DZ2

15 ...

[Page 16] Lumel DZ2

16 DZ2-07 Lubuskie Zak³ady Aparatów Elektrycznych LUMEL S.A. ul. Sulechowska 1 65-022 Zielona Góra - Poland Tel. (48-68) 329 51 00 (exchange) Fax: (48-68) 329 51 01 e-mail: [email protected] http://www.lumel.com.pl Export Department: Tel: (48-6...