Robe Color Spot 1200 AT User Manual

Download or browse on-line these Operation & User’s Manual for Robe Color Spot 1200 AT Flood Light.

Robe Color Spot 1200 AT Manual Information:

This manual for Robe Color Spot 1200 AT, given in the PDF format, is available for free online viewing and download without logging on. The guide contains 43 pages, and the size of the file at download is . The document type is Operation & User’s Manual.

Download Manual

Summary of Contents:

[Page 1] Robe Color Spot 1200 AT

1 ...

[Page 2] Robe Color Spot 1200 AT

2 Table of contents 1. Safety instructions......................................................................................................... 3 2.Operating determinations ............................................................................

[Page 3] Robe Color Spot 1200 AT

3 CAUTION! Keep this device away from rain and moisture! Unplug mains lead before opening the housing! FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY BEFORE YOU INITIAL START - UP! 1. Safety instructions Every person involved with instal...

[Page 4] Robe Color Spot 1200 AT

4 2.Operating determinations This device is a moving-head spot for creating decorative effects and was designed for indoor use only. If the device has been exposed to drastic temperature fluctuation (e.g. after transportation), do not switch it on i...

[Page 5] Robe Color Spot 1200 AT

5 3. Description of the fixture 1 - Yoke 2 - Front panel 3 - Moving head 4 - Tilt lock button (red) 5 - Tilt unlock button (green) 6 - Pan lock/unlock lever 7 - Handle 8 - Base Rear panel of the base 1 - Neutral fuse holder 2 - Live fuse holder 3...

[Page 6] Robe Color Spot 1200 AT

6 Head inside-top side 1 - Gobo wheel 2 2 - Colour wheel 3 - CMY/conver.filter module 4 - Objective 5 - Effect wheel 6 - Gobo wheel 1 7 - Lamp chamber Head inside-bottom side 8 - Frost lamellas 9 - Iris 10 - Termostat 11 - Zoom/Focus ...

[Page 7] Robe Color Spot 1200 AT

7 4. Installation 4.1 Connection to the mains Verify the power supply settings before applying power! The factory settings are printed next to the power switch.If you wish to change the power supply settings,see the next chapter. Installl a 3-prong g...

[Page 8] Robe Color Spot 1200 AT

8 4.3 Fitting the lamp DANGER ! Install the lamps with the device switched off only. Unplug from mains before ! To insert the lamp (MSR 1200 AT SA): 1.Disconnect the fixture from power and allow it to cool. 2.Loosen the 2 quarter-turn fasteners marke...

[Page 9] Robe Color Spot 1200 AT

9 4.4 Lamp adjustment The lamp holder is aligned at the factory. Due to differences between lamps, fine adjustment may improve light performance: 1.Switch on the fixture and after reset turn on the lamp. 2.Cancel all effects, open the shutter and foc...

[Page 10] Robe Color Spot 1200 AT

10 CAUTION! The gobo holder with the magnet must be placed in the same gobo position as it was placed before gobo replacement! Colour-wheel: 1.Gently bend out the colour module to release it from the fixative holes and eject it from the pressing sn...

[Page 11] Robe Color Spot 1200 AT

11 4.6 Rigging the fixture DANGER TO LIFE! Please consider the respective national norms during the installation! The installation must only be carried out by an authorized dealer! The installation of the fixture has to be built and constructed in a...

[Page 12] Robe Color Spot 1200 AT

12 For overhead use, always install a safety-rope that can hold at least 10 times the weight of the fixture. You must only use safety ropes with screw-on carabines. Pull the safety rope through the two apertures on the bottom of the base and over the...

[Page 13] Robe Color Spot 1200 AT

13 4.7 DMX-512 connection/connection between fixtures The fixture is equipped with both 3-pin and 5-pin XLR sockets for DMX input and output.The sockets are wired in parallel. Only use a shielded twisted-pair cable designed for RS-485 and 3-pin or ...

[Page 14] Robe Color Spot 1200 AT

14 4.8 Ethernet connection The fixtures on a data link are connected to the Ethernet with Art-Net communication protocol.The controlling software from PC (or lighting console) has to supported Art-Net protocol. Art-Net communication protocol is a 10 ...

[Page 15] Robe Color Spot 1200 AT

15 Colorspot 1200 AT- DMX protocol-Version 1.5 Mode 1 Mode 2 Value Function Type of control channel channel 1 1 Pan 0-255 Pan movement by 530° proportional 2 2 Pan Fine 0-255 Fine control of pan movement proport...

[Page 16] Robe Color Spot 1200 AT

16 Mode 1 Mode 2 Value Function Type of control channel channel 110 UV filter proportional 128 129 White proportional 130-139 Deep red step 140-149 Deep blue step 150-159 Green step 160-169 Orange s...

[Page 17] Robe Color Spot 1200 AT

17 Mode 1 Mode 2 Value Function Type of control channel channel 108-111 Macro 27 step 112-115 Macro 28 step 116-119 Macro 29 step 120-123 Macro 30 step 124-127 Macro 31 step 128-131 Macro 32 step 132-135 Ma...

[Page 18] Robe Color Spot 1200 AT

18 Mode 1 Mode 2 Value Function Type of control channel channel Rotation - set rotation on channel(s) 14 (18,19) 34-37 Gobo 1-Rainbow Chips (15030012) step 38-41 Gobo 2-Sun Man (15030013) step ...

[Page 19] Robe Color Spot 1200 AT

19 Mode 1 Mode 2 Value Function Type of control channel channel 46-49 Gobo 4-Bubbles 1 (15020128) step 50-53 Gobo 5-Dots in Circle (15020129) step 54-57 Gobo 6-Radial Dashes (15020130) step Shaking gobos...

[Page 20] Robe Color Spot 1200 AT

20 Mode 1 Mode 2 Value Function Type of control channel channel 196-199 Macro 5 step 200-203 Macro 6 step 204-207 Macro 7 step 208-211 Macro 8 step 212-215 Macro 9 step 216-219 Macro 10 step 220-223 Macro...

[Page 21] Robe Color Spot 1200 AT

21 32-63 No function (Shutter open) step 64-95 Strobe-effect from slow to fast proportional 96-127 No function (Shutter open) step 128-143 Opening pulse in sequences from slow to fast proportional ...

[Page 22] Robe Color Spot 1200 AT

22 6. Controller mode The fixtures are individually addressed on a data link and connected to the controller.The fixtures respond to the DMX signal from the controller. 6.1 DMX addressing There are 512 available channels on DMX link.Every fixture ...

[Page 23] Robe Color Spot 1200 AT

23 Iris Motorized adjustable iris,wide range of variable pulse effects. Frost Frost module provides variable frost for fine frosting. Focus-multistep zoom Motorized focus enables the beam to be focused anywhere on stage ,provided by the special multi...

[Page 24] Robe Color Spot 1200 AT

24 7.Control menu map Default settings=Bold print Fixture Address DMX Address 001 : 512 Ethernet Settings Set Ethernet Mode Disable Ethernet Enable Ethernet Set IP Address Default IP Address Custom IP Address Set ArtNet Universe (0 -255) Fixture i...

[Page 25] Robe Color Spot 1200 AT

25 Personality User Mode User A Settings User B Settings User C Settings DMX Presetting Mode 1 Ch.1 Pan : Ch.24 Dimmer Set Active Mode 2 Ch.1 Pan : Ch.32 Dimmer Fine Set Active Pan Reverse (On,Off) Tilt Reverse (On,Off) Lamp Presetting Lamp On...

[Page 26] Robe Color Spot 1200 AT

26 Manual Mode Presetted Effect Control Pan (Position 1,...,Position 6) : Dimmer (Position 1,...,Position 5) Manual Effect Control Pan (0-255) : Dimmer Fine (0-255) Stand- alone setting Music Trigger (On,Off) Presetting Playback Disabled Test Pro...

[Page 27] Robe Color Spot 1200 AT

27 8. Control menu The control panel situated on the front panel of the base offers several features. You can simply set the DMX address,read the number of the lamp or unit hours, switch On and Off the lamp, run test, make a reset and also use many f...

[Page 28] Robe Color Spot 1200 AT

28 1200 AT has been fabricated. Resetable Hours --- The function shows the number of the operation hours that the COLORSPOT 1200 AT has been powered on since the counter was last reset.In order to reset this counter to 0,press [ENTER] twice. Lamp On ...

[Page 29] Robe Color Spot 1200 AT

29 Fixture head (Top view) Fixture base (Top view) Fan 8 Fan 9 Fan 7 Fan 5 Fan 6 Fan 4 Near Lamp Temp. Fan 2 Fan 1 Fan 3 Board 3 Board 2 Board 1 Board Temp. Ambient Temp. IC2 MB IC1 MB IC3 MB Fan 10 Fan 11 IC4 MB ...

[Page 30] Robe Color Spot 1200 AT

30 8.3 Personality Use this menu to to modify COLORSPOT 1200 AT operating behavior. User mode --- Colorspot 1200 AT allows you to recall up to 3 user settings.After switching the fixture on for the first time, the User A settings are active.All chan...

[Page 31] Robe Color Spot 1200 AT

31 6 Special Functions 22 Gobo 2 F. Indexing 7 Pan/Tilt Macro 23 Effect Wheel 8 P./T. Macro Speed 24 Effect Indexing 9 Colour Wheel 25 Effect F. Index. 10 Cyan 26 Frost 11 Magenta 27 Iris 12 Yellow 28 Zoom 13 Conversion Filter 29 Focus 14 CMY Colour ...

[Page 32] Robe Color Spot 1200 AT

32 Time mode --- Pan and tilt will move with different speeds and they will come at the same time to end point (pan and tilt sets its optimal speed). Speed Mode --- Pan and tilt will move with the same speed as adjusted by the channel 6 (Pan/Tilt s...

[Page 33] Robe Color Spot 1200 AT

33 in a loop. Test Program In Loop --- The option starts built-in test program. Program 1 In Loop --- The option starts created program No. 1 Program 2 In Loop --- The option starts created program No. 2 Program 3 In Loop --- The option starts creat...

[Page 34] Robe Color Spot 1200 AT

34 Focus/Zoom/Frost --- This function resets focus,zoom and frost. Iris/Effect --- This function resets iris and effect wheel. 8.9 Special functions Use this menu for special services like adjusting lamp or adjusting effects. Lamp Adjustment --- T...

[Page 35] Robe Color Spot 1200 AT

35 10. Error and information messages Occured errors during fixture operation are signaled by warning icon on the display: Press [ESC] to see the current error messages. Description of error messages: Active Lamp Timer This message appears: 1. If you...

[Page 36] Robe Color Spot 1200 AT

36 Colour Wheel Error 1 (Colour Wheel Error 2 ) The messsages will appear after the reset of the colour wheel if this wheel is not located in the default position. Gobo 1 Wheel Error 1 (Gobo 1 Wheel Error 2 ) The messsages will appear after the rese...

[Page 37] Robe Color Spot 1200 AT

37 11. Technical specifications P ower supply: Magnetic ballast: Voltage:..............................208/230/250V AC, 50/60Hz ~ Main fuses: Live fuse:........T10A@230V Neutral fuse:....T10A@230V Electronic ballast: Voltage:............................

[Page 38] Robe Color Spot 1200 AT

38 Effect wheel - 3-facet prism, 5-facet prism and 2 glass effects rotating in both directions at different speeds. Prism outside diameter= 46.8 mm - Fine prism indexing and rotation - 16 Prism/gobo macros Strobe - Strobe effect with variable speed...

[Page 39] Robe Color Spot 1200 AT

39 Temperatures -Maximum ambient temperature : 40° C -Maximum housing temperature : 135° C Minimum distances -Min.distance from flammable surfaces: 1.2m -Min.distance to lighted object: 2.5m Dimensions and weight -Weight (magnetic ballast: 51.5 kg ...

[Page 40] Robe Color Spot 1200 AT

40 Beam path Lamp: MSR 1200 SA ...

[Page 41] Robe Color Spot 1200 AT

41 ...

[Page 42] Robe Color Spot 1200 AT

42 12. Maintenance and cleaning It is absolutely essential that the fixture is kept clean and that dust, dirt and smoke-fluid residues must not build up on or within the fixture. Otherwise, the fixture‘s light-output will be significantly reduced. ...

[Page 43] Robe Color Spot 1200 AT

43 ...