Zanussi ZHC 916X Instruction Booklet

[Page 1] Zanussi ZHC 916X

COOKER HOOD ZHC 916X INSTRUCTION BOOKLET ...

[Page 2] Zanussi ZHC 916X

2 Thank you for buying a Zanussi product. To enable you to use your appliance effectively and safely, please read this instruction book carefully before using the appliance and retain for future reference. If you require guidance in the use of the ap...

[Page 3] Zanussi ZHC 916X

3 IMPORTANT SAFETY INFORMATION These warnings are provided in the interests of your safety. Ensure that you understand them all before installing or using this appliance. Your safety is of paramount importance. If you are unsure about any of the mean...

[Page 4] Zanussi ZHC 916X

4 YOUR APPLIANCE OPERATING INSTRUCTIONS This cooker hood is designed to extract unpleasant odours from the kitchen, it will not extract steam. To obtain the best performance it is advisable to switch on the hood a few minutes before you start cooking...

[Page 5] Zanussi ZHC 916X

5 This cooker hood can be used to recirculate or extract contaminated air. Recirculation The cooker hood is supplied specified for use in the recirculation mode with the charcoal filter fitted. The contaminated air is cleaned by passing through the f...

[Page 6] Zanussi ZHC 916X

6 MAINTENANCE AND CLEANING Before carrying out any maintenance or cleaning isolate the cooker hood from the mains supply. The cooker hood must be kept clean, a build up of grease or fat can be a fire hazard. External Cleaning The metal casing, grille...

[Page 7] Zanussi ZHC 916X

7 To Remove the Charcoal Filter Push inwardly on the two retaining clips to disengage the security fixing and remove. This appliance can be a fire hazard if the grease and charcoal filters are not cleaned and replaced as recommended. Worktop Lighting...

[Page 8] Zanussi ZHC 916X

8 SOMETHING NOT WORKING SERVICE AND SPARE PARTS If, having followed these instructions carefully, your cooker hood fails to work properly please carry out the following checks. Symptom The cooker hood will not start The cooker hood is not working eff...

[Page 9] Zanussi ZHC 916X

9 PEACE OF MIND FOR TWENTY FOUR MONTHS STANDARD GUARANTEE CONDITIONS We, Zanussi, undertake that if within twenty four months of the date of the purchase this Zanussi built-in appliance or any part there of is proved to be defective by reason only of...

[Page 10] Zanussi ZHC 916X

10 INSTALLATION INSTRUCTIONS It is dangerous to alter the specifications or attempt to modify this product in any way. Technical Information DIMENSIONS HEIGHT (CANOPY): 73 mm HEIGHT (CHIMNEY): 450-850 mm WIDTH (CANOPY): 898 mm WIDTH (CHIMNEY): Ø200-...

[Page 11] Zanussi ZHC 916X

11 INSTALLING THE COOKER HOOD Please ensure that when the appliance is installed it is easily accessible to an engineer in the event of a breakdown. All installations must comply with the local authorities requirements for the discharge of exhaust ai...

[Page 12] Zanussi ZHC 916X

12 A: Built-in Electric Hob: 650mm clearance B: Built-in Gas hob: 700mm clearance C: Slot-in Electric Cooker: 685mm clearance D: Slot-in Gas Cooker: 787mm clearance Hob Clearance Heights The cooker hood is designed to be fitted over a cooking applian...

[Page 13] Zanussi ZHC 916X

13 B A08_10 O S07_09 O O INSTALLATION INSTRUCTIONS 100 100 ø 8 48 20 * 1 1 5 O 1 6 A08_08 K B 7 8 9 Draw a vertical line on the wall from the centre of the cooking appliance, using a spirit level and marking pen. This is to ensure the correct ...

[Page 14] Zanussi ZHC 916X

14 Adjusting Position (10) There are 2 adjustable hooks at the rear of the hood, which can be used to adjust its position as follows: - Turn screws L until the position of screws N coincides with the lower access holes. - Turn the screws N to adjust ...

[Page 15] Zanussi ZHC 916X

15 Regardless of which type of installation, any wooden shelves in the area where the hood is to be fitted must first be removed, drilled and later replaced. Drilling the shelves a) Using the template provided, and taking hole B as a point of referen...

[Page 16] Zanussi ZHC 916X

16 Air outlet directed upwards (Fig. 2a-b): - Remove the plastic plug from the upper part of the venting grill and replace it on the rear part (Fig. 16). Air outlet directed towards the wall (Fig. 3): - Remove the plastic frame from the air outlet (F...

[Page 17] Zanussi ZHC 916X

17 EE E E B Fixing the chimney a) Loosen the screws M fixing the two parts of the chimney and pull the inner section I (Fig. 21) almost all the way out. Remove the protective film P. b) Rest the lower section of the chimney in its housing on the to...

[Page 18] Zanussi ZHC 916X

18 Electrical connection and working test: 1. Remove the metal cover by unscrewing the four self tapping screws. 2. Connect the ‘Push-Fit’ connectors coming from the fan assembly to the canopy. 3. Position the terminals as illustrated under the c...

[Page 19] Zanussi ZHC 916X

19 In the event of your appliance requiring service, or if you wish to purchase spare parts please contact your local Service Force Centre by telephoning: 08705 929929 Your telephone call will be automatically routed to the Service Force centre cover...

[Page 20] Zanussi ZHC 916X

4329161_12 - 041207 © Electrolux plc 2002 ...