Simplex Ethernet Clock Installation Manual

[Page 1] Simplex Ethernet Clock

Simplex Ethernet Clock Power Over Ethernet (POE) Installation Manual ...

[Page 2] Simplex Ethernet Clock

Installation Manual Ethernet Clock Power Over Ethernet (POE) Inova Part Number: 715437 While reasonable efforts have been taken in the preparation of this document to insure its accuracy, Simplex assumes no liability ...

[Page 3] Simplex Ethernet Clock

TABLE OF CONTENTS Section 1 – Introduction and Network Planning ........................................... 1 Section 2: System Integration .......................................................................... 2 Non-PoE Enabled Hub/Swit...

[Page 4] Simplex Ethernet Clock

Section 1 – Introduction and Network Planning Simplex PoE clocks operate with the IEEE standard for Power Over Ethernet. The power for the clock is provided by a PoE injector or a PoE Switch. After you connect the clock, it will display th...

[Page 5] Simplex Ethernet Clock

Section 2: System Integration The diagrams below illustrate three options for system integration with your PoE-capable LAN. PoE-Enabled Hub/Switch In the simplest example, the Ethernet is already PoE-enabled (802.3AF) and is supporting...

[Page 6] Simplex Ethernet Clock

Non-PoE Enabled Hub/Switch and Single Simplex Ethernet Clock If the Ethernet is not currently PoE-enabled and is going to support a single Simplex Ethernet Clock, a Single Port Midspan Power Injector must be added to the 10/100 BaseT Ethern...

[Page 7] Simplex Ethernet Clock

Non-PoE-Enabled Hub/Switch and Multiple Simplex Ethernet Clocks If the Ethernet is not currently PoE-enabled and is going to support the Simplex Ethernet Clocks, a single or multiple Port Midspan Power Injector must be added to the 10/100 Ba...

[Page 8] Simplex Ethernet Clock

Recording Location, Static IP Address, and Host Name In order to make the management of your Simplex Ethernet Clock system as easy as possible, Simplex recommends that you record the Clock ID, Location, IP Address, and Host Name for each unit in...

[Page 9] Simplex Ethernet Clock

CLOCK ID# LOCATION IP ADDRESS Host Name ©2007 Simplex Time Re...

[Page 10] Simplex Ethernet Clock

Section 3: Unpacking The Simplex Ethernet Clock arrives fully assembled in a single package. Inspect all items and report any missing or damaged items using the standard reporting process on the company web site. Follow the directions ...

[Page 11] Simplex Ethernet Clock

Section 4: Installation Instructions The Simplex Ethernet Clock is available in a variety of mounting configurations. Please consult the appropriate system documentation for...

[Page 12] Simplex Ethernet Clock

Surface Mounting The following is a recommended procedure for surface mounting. No mounting kit is required. ©2007 Simplex Time Recorder Co. All rights reserved. ...

[Page 13] Simplex Ethernet Clock

Surface Mounting Procedure 1. Determine the clock mounting location. 2. Mark two points 10” (25.4 cm) apart, level and centered on the data cable outlet. 3. Insert two flat-head fasteners suitable for the wall surface at the marked po...

[Page 14] Simplex Ethernet Clock

Pendant Mounting – Single or Double The following is a recommended procedure for pendant mounting. This procedure requires a mounting kit, (model ONT4 KIT for four digit clocks or ONT6 Kit for six digit clocks), and some additional hardware. ...

[Page 15] Simplex Ethernet Clock

5. Position the keyhole slots located on the rear of the clock over the mounting tabs. 6. Pull the clock slightly downwards until the unit is seated. Repeat for the second clock if two clocks are being installed back-to- back. ...

[Page 16] Simplex Ethernet Clock

Cantilever Mounting – Single or Double The following is a recommended procedure for cantilever mounting. This procedure requires a mounting kit, model ON4TKIT or ONT6KIT. Determine the clock mounting location. 1. Using the templat...

[Page 17] Simplex Ethernet Clock

4. Securely attach the mounting unit to the wall using fasteners suitable for the wall surface. 5. Lift the Simplex Ethernet Clock into place and insert the data cable into the jack located on the back of the clock. 6. Position the keyhole...

[Page 18] Simplex Ethernet Clock

Section 5:Installation Wrap-up and Verification 1. Verify that each Simplex Ethernet Clock powers up and displays an IP Address. 2. If the clocks are statically addressed, record the IP Address and location of each clock in the table provi...

[Page 19] Simplex Ethernet Clock

Section 6: Telnet Command Map This section covers how to configure the Simplex Ethernet Clock once it has been installed. Once you have established a Telnet connection, log on using the following User ID and Password: User ID: iclock Pass...

[Page 20] Simplex Ethernet Clock

dst dst [options]: Used to configure and display the Clock's Daylight Saving Time settings. While in Daylight Saving Time, one hour is added to the time display. • Disable the Daylight Saving Time adjustment. [dst -none] • ...

[Page 21] Simplex Ethernet Clock

• [-h hostname] Set the hostname – default is iclock. (Optional) • [-x] Show all Interface data. log Used to enable or disable logging and to print the log file to the session screen netstat Lists all TCP connections nslo...

[Page 22] Simplex Ethernet Clock

reboot Shuts down and cleanly reboots the system. Note that this takes tens of seconds to complete sntp sntp [options]: Used to configure and display the SNTP Time Server settings. • [-h host] Set the SNTP Time Server hostname or ip ...

[Page 23] Simplex Ethernet Clock

update Used to update the clock firmware update <tftp_server> <filename> Updates the clock firmware. • tftp server - the server to retrieve the update file from • filename - the file containing the new firmware code in...