SMC Networks Corsair-F4U Instruction Manual

Download or browse on-line these Instruction Manual for SMC Networks Corsair-F4U Toy.

SMC Networks Corsair-F4U Manual Information:

This manual for SMC Networks Corsair-F4U, given in the PDF format, is available for free online viewing and download without logging on. The guide contains 20 pages, and the size of the file at download is . The document type is Instruction Manual.

Download Manual

Summary of Contents:

[Page 1] SMC Networks Corsair-F4U

Instruction Manual Wingspan : 1670mm Length : 1350mm Weight : 3400gr - 4000gr Engine : 61/75 two stroke Radio : 5 servo + 1 servo retract / 6 channel g ...

[Page 2] SMC Networks Corsair-F4U

MAIN GEAR ASSEMBLY (2) Main gear (90 degree) (2) One set landing gear (2) 55mm diameter wheel (2) Connector gear (2) M2 metal clevis (2) Silicone tube (8) 3mm x 12mm screw (2) 1.7mm x 300mm metal pushrod (2) 1.7mm x 60mm metal rod ...

[Page 3] SMC Networks Corsair-F4U

TOOLS AND SUPPLIES NEEDED • Medium C/A glue • 30 minute epoxy • 6 minute epoxy • Hand or electric drill • Assorted drill bits • Modeling knife • Straight edge ruler SUGGESTION To avoid scratching your new airplane, do not unwrap the p...

[Page 4] SMC Networks Corsair-F4U

6. Tie the string from inside the wing to the end of the servo wire. Pull the servo wire through the wing with the string. Tape the servo wire to the wing to prevent it from falling back into the wing. 6 3 CORSAIR F4U Instruction Manual 4 Remove ...

[Page 5] SMC Networks Corsair-F4U

11 7 10 7. Temporarily position the aileron servo into the servo bay. Drill a 1.6mm hole through the four mounting holes of the servo, drilling through the plywood mounting plate in the wing. Install and remove a servo mounting screw into each o...

[Page 6] SMC Networks Corsair-F4U

2. Locate one nylon servo arm, and using wire cutters, remove all but one of the arms. Using a 2mm drill bit, enlarge the third hole out from the center of the arm to accommodate the aileron pushrod wire. 3. Plug the aileron servo into the receiv...

[Page 7] SMC Networks Corsair-F4U

20 INSTALLING THE landing gear (without the retractable gear) 1. Install the landing gear ( included with the kit) to the wooden block. 2. Remove the covering. 4. Install the wheel. 5. Make the same way for the second landing gear. 16 6 CORSAIR F4U...

[Page 8] SMC Networks Corsair-F4U

9. Insert the retract landing gear into the block and mark four holes onto the block. Take out the retract landing gear and drill four horns into the block using 2mm pit. 27 28 10. Reinstall the retract landing gear using four 3mm x 12mm screw. ...

[Page 9] SMC Networks Corsair-F4U

30 31 32 33 8 CORSAIR F4U Instruction Manual 11. Install the wheel into the connector of the gear. 12. Install the metal connector into the landing gear. 13. Make the same way for the second retract landing gear 14. Install two metal connector to ...

[Page 10] SMC Networks Corsair-F4U

9 CORSAIR F4U Instruction Manual Close position INSTALLING THE HORIZONTAL STABILIZER 1. Using a modeling knife, cut away the covering from the fuselage for the stabilizer and remove it. 34 36 2. Draw a center line onto the horizontal stabilizer a...

[Page 11] SMC Networks Corsair-F4U

40 2. Remove the covering. 10 CORSAIR F4U Instruction Manual 8. After the epoxy has fully cured, remove the masking tape or T-pins used to hold the stabilizer in place and carefully inspect the glue joints. Use more epoxy to fill in any gaps that ...

[Page 12] SMC Networks Corsair-F4U

2. Place the engine into the engine mount and align it properly with the front of the cowling. The distance from the firewall to the front of the engine thrust washer should 110mm. If your engine is equipped with a remote needle valve, we su...

[Page 13] SMC Networks Corsair-F4U

4. Now, remove the engine. Using a 5mm drill bit, drill holes through the firewall and the forward bulkhead at the marks made. 5. Slide the pushrod housing through the hole in the firewall, through the hole in the forward bulkhead, and into the s...

[Page 14] SMC Networks Corsair-F4U

13 CORSAIR F4U Instruction Manual 50 51 SERVO INSTALLATION INSTALLING THE FUSELAGE SERVOS 1. Install the rubber grommets and brass collets into the elevator, rudder and throttle servos. Test fit the servos into the servo tray. Trim the tray if ...

[Page 15] SMC Networks Corsair-F4U

14 CORSAIR F4U Instruction Manual 54 INSTALLING THE RUDDER PUSHROD 1. Locate the pushrod exit slot on the right of the fuselage. 2. Carefully cut away the covering material from the slot. 3. Working from inside the fuselage, slide the threa...

[Page 16] SMC Networks Corsair-F4U

15 CORSAIR F4U Instruction Manual 58 60 61 62 59 ! MOUNTING THE COWL 1. Remove the muffler and needle valve assembly from the engine. Slide the fiberglass cowl over the engine. 2. Measure and mark the locations to be cut out for engine head cle...

[Page 17] SMC Networks Corsair-F4U

FINAL ASSEMBLY INSTALLING THE SPINNER Install the spinner back-plate, propeller and spinner cone. The spinner cone is held in place using two 3mm x 20mm wood screws. The propeller should not touch any part of the spinner cone. If it dos...

[Page 18] SMC Networks Corsair-F4U

105mm BALANCING 1. It is critical that your airplane be balanced correctly. Improper balance will cause your plane to lose control and crash. THE CENTER OF GRAVITY IS LOCATED 105mm BACK FROM THE LEADING EDGE OF THE WING, AT THE FUSELAGE. This lo...

[Page 19] SMC Networks Corsair-F4U

I/C FLIGHT WARNINGS Always operate in open areas, away from factories, hospitals, schools, buildings and houses etc. NEVER fly your aircraft close to people or built up areas. THE PROPELLER IS DANGEROUS Keep fingers, clothing (ties, shirt sleev...

[Page 20] SMC Networks Corsair-F4U

I/C FLIGHT GUIDELINES Made in Vietnam When ready to fly, first extend the transmitter aerial. Operate the control sticks on the transmitter and check that the control surfaces move freely and in the CORRECT directions. ALWAYS land the model INTO ...