Pro'sKit PT-1080 User Manual

[Page 1] Pro'sKit PT-1080

PT-1080 Li-ion Cordless drill driver 10.8V User’s Manual 1 st Edition , 2011 ©2011 Copy Right by Prokit’s Industries Co., Ltd. ...

[Page 2] Pro'sKit PT-1080

1 ...

[Page 3] Pro'sKit PT-1080

Before any use, refer to the corresponding paragraph in the present manual. DESCRIPTION OF SYMBOLS Symbols are used in this manual to attract your attention to possible risks .The safety symbols and the explication which accompany them must...

[Page 4] Pro'sKit PT-1080

d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock. e) When operating a po...

[Page 5] Pro'sKit PT-1080

4) Power tool use and care a) Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed. b) Do not use the power tool if the s...

[Page 6] Pro'sKit PT-1080

SPECIAL SAFETY ADVICE FOR CORDLESS DRILL Wear ear protectors with drills. Exposure to noise can cause hearing loss. Use auxiliary handles supplied with the tool. Loss of control can cause personal injury. Only plug the Battery Charger in at ...

[Page 7] Pro'sKit PT-1080

Technical Data Rated Voltage DC 10.8V No-load Speed 0-350/0-1100rpm Range of Drill Bit sizes 0.8-10 mm Steel: Ø 6 mm Max. Drilling Capacity Wood: Ø16 mm Battery pack Voltage DC 10.8V Battery cell Li-ion Batteries, 1300mAh Charge...

[Page 8] Pro'sKit PT-1080

Initial operation Insertion and Removal of Rechargeable Battery Ensuri ng the correct orientation between the battery and the battery compartment, insert the rechargeable battery into the machine. Do not apply force when inserting the batte...

[Page 9] Pro'sKit PT-1080

Inserting Tool Bits / 10mm Keyless chuck: Important! Always remove the battery before you change the drill or screw bit to avoid unintentional starting of the machine. The cordless drill has a keyless chuck (2). Make sure that the drill or scr...

[Page 10] Pro'sKit PT-1080

the arrow points to on the torque control knob, the larger the maximum torque that can be applied before the torque clutch will slip. To set the machine to maximum available torque twist the torque control knob until the arrow points to the drill ...

[Page 11] Pro'sKit PT-1080

5. Drilling in Stone, Brick, Masonry or similar For drilling in walls, stone, masonry etc. use a masonry-bit. Do not put too much pressure on the machine. Follow the same instructions as for drilling in metal. 6. Using the Drill as a Screw-drive...

[Page 12] Pro'sKit PT-1080

PT-1080 10.8V 1300mAH 鋰電池電鑽 說明書 使用之前，請仔細閱讀當前說明書中的相應章節。 符號描述 爲了引起你在使用過程中存在的風險的注意，在說明書中添加了符號註�...

[Page 13] Pro'sKit PT-1080

1）工作區域 a) 保持工作區域的乾淨與明亮。混亂與黑暗的區域容易引起事故發生。 b) 不要在易爆的環境中維修電動工具，諸如在存放有易燃液體、氣體或者灰塵的環境 下。電動工具的�...

[Page 14] Pro'sKit PT-1080

d) 儲存閒置的電動工具時要遠離兒童能觸及到的地方，不要讓不熟悉電動工具或指導說 明的人去操作電動工具，未經訓練的人使用電動工具是危險的。 e) 維修電動工具。檢查錯位部份或�...

[Page 15] Pro'sKit PT-1080

技術參數 額定電壓 DC 10.8V 空載轉速 0-350/0-1100rpm 鑽頭尺寸範圍 0.8-10 mm 鋼材: Ø 6 mm 最大鑽孔能力 木材: Ø16 mm 電池組的電壓 DC 10.8V 電池 鋰離子電池, 1300mAh 充電器 PT-1080F PT-108...

[Page 16] Pro'sKit PT-1080

初始操作  可充電電池的插入和去除 首先，請確保電池和電池倉之間的方向正確，電池可以輕鬆插入， 不必使用太大的力氣。電池必須完全插入，直到電池艙自動鎖定 到位。要取出電�...

[Page 17] Pro'sKit PT-1080

正向/反向開關： 重要！反向旋轉鍵使用之前機器必須是完全停止的，否則可能會損壞機器。 順時針或逆時針旋轉可以通過反向旋轉鍵切換，反之亦然。如果反向旋轉鍵調節在中心位 �...

[Page 18] Pro'sKit PT-1080

3、鑽在金屬 金屬鑽孔使用鋼鑽頭。期間要不斷的用非易燃易爆的冷卻液冷卻鑽頭。用一個比較合適的 支架綁好工作件，工件應平放在工作臺上。要鑽的孔中心位置做好記號，不要對工�...

[Page 19] Pro'sKit PT-1080

18 ...

[Page 20] Pro'sKit PT-1080

19 ©2011 Prokit’s Industries Co., LTD. All rights reserved 2011001(C) ...