Sony HDC1000 Maintenance Manual

Download or browse on-line these Maintenance Manual for Sony HDC1000 Camcorder, CCD Cameras.

Sony HDC1000 Manual Information:

This manual for Sony HDC1000, given in the PDF format, is available for free online viewing and download without logging on. The guide contains 144 pages, and the size of the file at download is . The document type is Maintenance Manual.

Download Manual

More Manuals:

In case you failed to obtain relevant information in this document, please, look through related operating manuals and user instructions for Sony HDC1000. Just click one of the links below to go to the selected manual:

Summary of Contents:

[Page 1] Sony HDC1000

HD COLOR CAMERA HDC1000 HDC1400 HDC1500 HDC1550 HDC1580 MAINTENANCE MANUAL Volume 1 1st Edition (Revised 4) Serial No. 10001 and Higher: HDC1000 (UCJ) Serial No. 40001 and Higher: HDC1000 (CE) Serial No. 10001 and Higher: HDC1400 (UC) Serial No. 1000...

[Page 2] Sony HDC1000

HDC1000/V1(E) ! WARNING This manual is intended for qualified service personnel only. To reduce the risk of electric shock, fire or injury, do not perform any servicing other than that contained in the operating instructions unless you are qualified ...

[Page 3] Sony HDC1000

HDC1000/V1(E) Vorsicht! Explosionsgefahr bei unsachgemäßem Austausch der Batterie. Ersatz nur durch denselben oder einen vom Hersteller empfohlenen ähnlichen Typ. Entsorgung gebrauchter Batterien nach Angaben des Herstellers. ATTENTION Il y a dang...

[Page 4] Sony HDC1000

HDC1000/V1(E) Voor de klanten in Nederland Gooi de batterij niet weg maar lever deze in als klein chemisch afval (KCA). Für Kunden in Deutschland Entsorgungshinweis: Bitte werfen Sie nur entladene Batterien in die Sammelboxen beim Handel oder den Ko...

[Page 5] Sony HDC1000

1 HDC1000/V1(E) Table of Contents Manual Structure Purpose of this manual ................................................................. 4 Related manuals ........................................................................... 4 1. Service Ove...

[Page 6] Sony HDC1000

2 HDC1000/V1(E) 2-8. Replacing the Connectors (HDC1400/1500/1550/1580) ........................................ 2-12 2-8-1. EARPHONE Jack (CN-2640 Board) .................. 2-12 2-8-2. DC IN Connector (CN-2623 Board) ................... 2-13 2-8-3. I...

[Page 7] Sony HDC1000

3 HDC1000/V1(E) 3-8. Video System Adjustment (HDC1550) ........................ 3-26 3-8-1. Demodulation Tuning Adjustment ......................3-26 3-8-2. Return Sync Level Adjustment ........................... 3-26 3-8-3. Return Frequency Adjustm...

[Page 8] Sony HDC1000

4 HDC1000/V1(E) Purpose of this manual This manual is the maintenance manual Volume 1 for HD Color Camera HDC1000/ 1400/1500/1550/1580. This manual describes the information items that premise the service based on the components parts such as service...

[Page 9] Sony HDC1000

1-1 HDC1000/V1(E) Section 1 Service Overview 1-1. Checking before Installation 1-1-1. Checking the ROM and Software Version When connecting the peripheral equipment in the list below to HDC1000/1400/ 1500/1550/1580, be sure to check that the ROM and ...

[Page 10] Sony HDC1000

1-2 HDC1000/V1(E) 1-2. Connectors and Cables 1-2-1. Connector Input/Output Signals HDC1000 Connector Layout !\ 24350!'!,89 7 !- !]![ 1 !;!= != ...

[Page 11] Sony HDC1000

1-3 HDC1000/V1(E) 1 0 2 3 *1 5 4 6 7 8 9 !- !. !- !] !, !' != != !; !\ *: HDC1500 only * 1: There are no connectors on HDC1580. * 2: There are no connectors on HDC1400/1550. * *1 *2 * *1 *2 HDC1400/1500/1550/1580 Connector Layout ...

[Page 12] Sony HDC1000

1-4 HDC1000/V1(E) 1 23 4 88 88 8 RET CONTROL (6P FEMALE) (External view) No. Signal I/O Specifications 1 INCOM 1 IN Zi > 10 kZ MIC-ON/OFF ON : GND OFF : OPEN 2 INCOM 2 IN Zi > 10 kZ MIC-ON/OFF ON : GND OFF : OPEN 3GND —— 4 RET 3-ON/OFF IN Z...

[Page 13] Sony HDC1000

1-5 HDC1000/V1(E) 1 7 6 5 4 3 2 8 21 3 !/!/ !/!/ !/ REMOTE (8P FEMALE) (External view) No. Signal I/O Specifications for RCP for TRUNK (RS422A) 1 TX (X) TX1 (+) OUT SERIAL DATA OUT 2 TX (Y) TX1 (_) OUT /TRUNK1 DATA OUT (for RS-422A) 3 TX (X) RX1 (+) ...

[Page 14] Sony HDC1000

1-6 HDC1000/V1(E) 18 36 1 19 !\!\ !\!\ !\ LENS (36P FEMALE) (HDC1000) (External view) No. Signal I/O Specifications 23 RET 3-ON IN Zi > 10 kZ ON : GND OFF : High impedance 24 LENS-ADR-0 IN * 1 25 LENS-ADR-1 IN * 1 26 LENS-ADR-2 IN * 1 27 LENS-ADR-...

[Page 15] Sony HDC1000

1-7 HDC1000/V1(E) EX 2 ON 30 kΩ EX 0.8 ON 13 123456789101112 25 1415161718192021222324 !\!\ !\!\ !\ LENS (12P FEMALE) (HDC1400/1500/1550/ 1580) (External view) No. Signal I/O Specifications 1 RET VIDEO IN ENABLE : 0 V ENABLE DISABLE : +5 V or OPEN ...

[Page 16] Sony HDC1000

1-8 HDC1000/V1(E) 2 9 1 8 10 1211 37 64 5 !;!; !;!; !; VF (20P FEMALE) (HDC1400/1500/1550/1580) (External view) No. Signal I/O Specifications 1 S-DATA IN/OUT TTL level 2 NC No connection 3 NC No connection 4 SCK OUT TTL level 5 NC No connection 6 NC ...

[Page 17] Sony HDC1000

1-9 HDC1000/V1(E) 21 3 !,!, !,!, !, TRACKER (10P FEMALE) (External view) No. Signal I/O Specifications 1 TRACKER OUT TRACKER RECEIVE/PGM LEFT _20 dBu unbalanced 2 GND (TALK) —— GND for TRACKER TALK 3 GND (RECEIVE/ —— GND for RECEIVE/PGM/TL PG...

[Page 18] Sony HDC1000

1-10 HDC1000/V1(E) 1-2-3. Connection Connectors/Cables Connection made with the connector panels during instal- lation or service, should be made with the connectors/ complete cable assemblies specified in the following list, or equivalent parts. Ind...

[Page 19] Sony HDC1000

1-11 HDC1000/V1(E) PA-317 CN-2579 TG-243 DR-528 BI-175 BI-175 CN-2578 BI-175 SWITCHING REGULATOR DC-DC COVERTER CN-2602 SDI-84 DPR-265 SW-1233 AT-166 CN-2603 (for UCJ) CN-2603B (for CE) CN-2608 CN-2671 CN-2671 CN-2609 LE-291 LE-309 CN-2604 CN-2605 CN...

[Page 20] Sony HDC1000

1-12 HDC1000/V1(E) PA-317 (HDC1400/1500) PA-317C (HDC1580) CN-2579 TG-243 (HDC1500) TG-243B (HDC1400) TG-243C (HDC1580) DR-528 BI-175 BI-175 BI-175 CN-2578 HDC1400/1500/1580 DC-DC COVERTER SWITCHING REGULATOR AT-163 AU-298 DAP-33 VDA-63 MB-1059 SW-12...

[Page 21] Sony HDC1000

1-13 HDC1000/V1(E) PA-317 CN-2579 TG-243 DR-528 BI-175 BI-175 BI-175 CN-2578 HDC1550 DC-DC COVERTER SWITCHING REGULATOR AT-163 AU-298 DAP-33 VDA-63 MB-1059 SW-1245 SW-1240 SW-1239 SW-1238 SW-1236 TR-136 MX-109 SW-1273 SW-1242 SW-1241 (for UC) SW-1241...

[Page 22] Sony HDC1000

1-14 HDC1000/V1(E) 1-4. Opening/Closing the Side Panel HDC1000 1. Unscrew the two lock screws of the side panel. 2. While sliding the safety lock toward the lens, open the side panel by holding the handle. 3. Close the side panel and tighten securely...

[Page 23] Sony HDC1000

1-15 HDC1000/V1(E) 1-5. Switch Settings AT-163 Board Ref. No. Name Description Factory setting S1-1 Reserve Not used (Fixed to OFF) OFF S1-2 All Preset FRAM clear OFF S1-3 Reserve Not used (Fixed to OFF) OFF S1-4 Firmware Load Forcibly upgrading of f...

[Page 24] Sony HDC1000

1-16 HDC1000/V1(E) AU-298 Board Ref. No. Name Description Factory setting S1 Reserve Not used (Fixed to NORM) NORM S2 Reserve Not used (Fixed to NORM) NORM S3-1 AB POWER MIC1 Switch ON to supply +12 V for MIC POWER to the OFF microphone connected to ...

[Page 25] Sony HDC1000

1-17 HDC1000/V1(E) S1 A B C 12 TG-243/243C BOARD (SIDE A) SDI-84 Board (HDC1000/1500) SDI-84C Board (HDC1400/1580) Ref. No. Name Description Factory setting HDC1000/1500 HDC1400/1580 S201-1 TEST Not used (Fixed to OFF) OFF OFF S201-2 PROMPTER2 OUT ...

[Page 26] Sony HDC1000

1-18 HDC1000/V1(E) TR-136 Board (HDC1550) Ref. No. Name Description Factory setting S1-1 When this switch is set to ON, the multiformat OFF color-bar signal is output from the built-in video test signal generator. S1-2 Spare (not used) OFF S1-3 S1-4 ...

[Page 27] Sony HDC1000

1-19 HDC1000/V1(E) When the conductive part is gold (HDC1000) Board Flexible card wire Board Pin Gold : Parts No. AT-166G 30 1-831-132-11 SW-1233G CN-2609G 30 1-831-118-11 MB-1060G CN-2579G 40 1-831-658-11 PA-317G CN-2579G 30 1-831-656-11 DR-528G DR-...

[Page 28] Sony HDC1000

1-20 HDC1000/V1(E) 1-6-2. Notes for Replacing the Board Replace the board with a board of the same number as the spare part number of the board to be removed when replacing a board. Example: A spare part number is put on the board. 1-6-3. Notes for R...

[Page 29] Sony HDC1000

1-21 HDC1000/V1(E) 1-7. Cleaning the Vent Portion of the Fan (HDC1400/1500/1550/1580) The ventilate bracket for preventing from dust is attached in the vent portion of the fan. Clean the ventilate bracket every two or three months. Clogging may cause...

[Page 30] Sony HDC1000

1-22 HDC1000/V1(E) Optical contacts (white) [Female connector] 1. Insert the optical connector cleaner straight. Ensure that it is held straight when inserting. 2. Apply sufficient pressure (approximately 600 g to 700 g) to ensure that the optical co...

[Page 31] Sony HDC1000

1-23 HDC1000/V1(E) Insert the shorter nose end Shock absorber portion Handle 1-8-2. When the Optical Connector Cleaner (Commercially Available) is not Available Tools required . Alignment sleeve remover HC-001 (for female connector) Sony P/N: J-6480-...

[Page 32] Sony HDC1000

1-24 HDC1000/V1(E) 1-10. Notes on Flexible Card Wire 1-10-1. Disconnecting/Connecting Flexible Card Wire The flexible card wires are used between the boards of HDC1000/1400/1500/1550/1580. Take care not to bend forcedly these flexible card wires. Thi...

[Page 33] Sony HDC1000

1-25 HDC1000/V1(E) Flexible card wire Connector Connector latch A B Flexible card wire Connector Connector latch A B Insulating surface Flexible card wire Connector Connector latch A B Insulating surface Flexible card wire Connector Connector latch A...

[Page 34] Sony HDC1000

1-26 HDC1000/V1(E) 100 unit : mm SW-1273(CN1) MB-1059(CN11) Conductive surface Insulating surface 55 Insulating surface Insulating surface unit : mm CN-2609(CN3) MB-1060(CN6) 1-10-2. Forming of the Flexible Card Wire If using a new flexible card wire...

[Page 35] Sony HDC1000

1-27 HDC1000/V1(E) 1-11. Notes on Replacement of Circuit Board 1-11-1. Description on EEPROM Data The table below gives the stored data of EEPROM (FRAM) on every printed circuit board. Board Ref. No. Stored data AT-163 IC133, IC139, Board adjustment ...

[Page 36] Sony HDC1000

1-28 HDC1000/V1(E) S1 S2 S3 A B C D 123 AU-298 BOARD (SIDE A) 1-12. Setting Microphone Power and Intercoms 1-12-1. How to Supply a Power of ++ ++ +12 V HDC1000/1400/1500/1550/1580 can supply +12 V for MIC POWER to the microphone connected to t...

[Page 37] Sony HDC1000

1-29 HDC1000/V1(E) HDC1000 Tool Memory Stick Preparation Copy the upgrading program to the Memory Stick in the following steps. n To get the upgrading program (program files “hdc1000.rom” and “boot.rom”), contact your local Sony Sales Office/...

[Page 38] Sony HDC1000

1-30 HDC1000/V1(E) Procedures 1. Open the right side panel (HDC1000), or inside panel (HDC1400/1500/1550/1580). (Refer to Section 1-4.) 2. Extend the AT-163 board using the EX-738 board. 3. Insert the Memory Stick in which the upgrading program is al...

[Page 39] Sony HDC1000

1-31 HDC1000/V1(E) Corresponding PLD PLD EPR connector Project file No. (Ref No./board name) (Ref No./board name) IC404/AT-163 CN401/AT-163 *7 E_000_001_88_xx IC403/AT-163 *1 IC201/DAP-33 CN2/DAP-33 *7 E_000_001_89_xx IC202/DAP-33 *2 IC408/SDI-84/8...

[Page 40] Sony HDC1000

1-32 HDC1000/V1(E) 1-15. Note on Replacement of Lithium Battery A lithium battery is mounted on the DAP-33 board to back up Real Time Clock (RTC). If a battery comes to the lifetime, then RTC stops. Therefore the battery replacement is required. DAP-...

[Page 41] Sony HDC1000

1-33 HDC1000/V1(E) No. Description Sony Part No. 1 KNOB (DIA 3) ASSY, VOLUME X-3167-563-X 2 KNOB, VOLUME 6 3-602-483-0X 3 CAP, CONNECTOR 3-605-338-0X 4 KNOB, VOLUME DIA.6 3-872-577-0X 5 SHIELD CUSHION (C) 3-615-750-6X 6 BAND, CLAMP 3-612-712-0X 7 PAC...

[Page 42] Sony HDC1000

1-34 HDC1000/V1(E) No. Description Sony Part No. 1 COVER, SWITCH 3-676-244-0X 2 COVER, SWITCH 3-676-244-2X 3 BUTTON, VTR START 3-679-668-0X 4 PACKING, VF 3-710-024-0X 5 CALL COVER 3-857-347-0X 6 SHEET, HANDLE 3-872-563-0X 7 PAD ASSY, SHOULDER A-8286-...

[Page 43] Sony HDC1000

1-35 HDC1000/V1(E) 1-16-3. Periodic Check/Replacement Parts This table does not describe the guarantee period of part. The replacement period of each part is changed according to the environment and condition. Refer to the “Section 2 Replacement of...

[Page 44] Sony HDC1000

1-36 HDC1000/V1(E) Example : MDA xxxxx Serial number for the CCD unit CCD block type 1-17. Description of CCD Block Number Every CCD unit has its own ID number called CCD block number. It shows the CCD block type and serial number for the CCD block. ...

[Page 45] Sony HDC1000

2-1 HDC1000/V1(E) Front panel assembly Hexagon-socket bolts (3 x 8) Hexagon-socket bolts (3 x 8) Spring washers Spring washers B2.6 x 6 Section 2 Replacement of Main Parts 2-1. Replacing the CCD Unit n Never remove or install the CCD unit with the p...

[Page 46] Sony HDC1000

2-2 HDC1000/V1(E) 5. Remove the three screws, and remove the transporta- tion holder from the CCD unit for repair (option). 6. Install the CCD unit by reversing the steps above. n When installing the CCD unit, adjust the boss of the front assembly to...

[Page 47] Sony HDC1000

2-3 HDC1000/V1(E) 2-1-2. HDC1400/1500/1550/1580 1. Loosen the four screws, and remove the front assem- bly. 2. Remove the four hexagon-socket bolts and four spring washers, and remove the front panel assembly. Front assembly B3 x 10 (with stopper) B3...

[Page 48] Sony HDC1000

2-4 HDC1000/V1(E) B2 x 4 B2 x 4 B2 x 4 CN2 CN1 OHB cover CN-2579 board Special screws (M2) B2 x 4 CN2 CN1 DR-528 board 2-2-2. CN-2579 Board 1. Remove the five screws to detach the OHB cover. 2. Disconnect the flexible card wires from the connectors...

[Page 49] Sony HDC1000

2-5 HDC1000/V1(E) B2 x 4 CN1 TG-243 board B2 x 4 B2 x 4 CN301 CN201 CN101 PA-317 board B2 x 4 B2 x 4 CN402 PA-317 board Flexible card wire Heat transfer sheets Heat conduction plate 2-2-3. PA-317 Board 1. Remove the five screws to detach the OHB co...

[Page 50] Sony HDC1000

2-6 HDC1000/V1(E) B2 x 4 CN4 CN3 CN2 B2 x 4 B2 x 4 OHB holder CN-2578 board 2-2-5. CN-2578 Board 1. Remove the CN-2579 board. (Refer to Section 2-2-2.) 2. Remove the DR-528 board. (Refer to Section 2-2-1.) 3. Remove the PA-317 board. (Refer to Sectio...

[Page 51] Sony HDC1000

2-7 HDC1000/V1(E) Connector CCD unit Fixing screw of the filter disk unit (with stopper) Fixing screw of the filter disk unit (with stopper) Filter disk unit 2-3-2. HDC1400/1500/1550/1580 1. Remove the inside panel. (Refer to Section 1-4.) 2. Dis...

[Page 52] Sony HDC1000

2-8 HDC1000/V1(E) 2-4. Replacing the Fan (HDC1000) c If the fan is out of order, the inside temperature of the unit will rise. Touching the inside in this state may cause a burn. When replacing the fan, allow a few minutes after powering off until th...

[Page 53] Sony HDC1000

2-9 HDC1000/V1(E) 5. Remove the three screws to detach the lower rail. 6. Disconnect the fan harness from the connector (CN4) on the MB-1059 board. 7. Remove the cushion (FAN) from the DC fan. 8. Install the front DC fan by reversing the steps above....

[Page 54] Sony HDC1000

2-10 HDC1000/V1(E) DPR rear bracket Fan harness CN18 MB-1059 board DC-DC converter 6. Install the rear DC fan by reversing the steps above. m . Be careful of the orientation of the label side and the harness when installing the DC fan. . Attach the d...

[Page 55] Sony HDC1000

2-11 HDC1000/V1(E) Handle Handle lock knob Screws (M2) Lever Top cover (02) 2-6. Replacing the VF DISP Switches (HDC1400/1500/1550/1580) (SW-1237 Board) 1. Remove the front assembly. (Refer to Section 2-1.) 2. Loosen the handle lock knob, and turn th...

[Page 56] Sony HDC1000

2-12 HDC1000/V1(E) CN-2640 board CN1 Washer EARPHONE jack Fixing nut of the EARPHONE jack Unsolder MIC panel assembly 2-8. Replacing the Connectors (HDC1400/1500/1550/1580) n Be careful not to bend the flexible card wire. This shortens the wire life...

[Page 57] Sony HDC1000

2-13 HDC1000/V1(E) Screws (M2) Screws (M2) CN-2619 board MIC panel assembly CN-2623 board SDI 2/SDI connector CN2 CN2 CN1 CN1 Hold the plug to remove. Do not attempt to remove by pulling the cable. OK NG CN-2621 board 5. Remove the two screws, and re...

[Page 58] Sony HDC1000

2-14 HDC1000/V1(E) 2-8-3. INTERCOM 1/2 Connector (CN-2618 Board) 1. Remove the six screws and pull out the INTERCOM panel assembly. 2. Disconnect the flexible card wire from the connector (CN1) on the SW-1273 board. 3. Remove the two screws, and remo...

[Page 59] Sony HDC1000

2-15 HDC1000/V1(E) 2-8-5. MIC 1 IN Connector (CN-2615 Board) 1. Remove the inside panel and outside panel. (Refer to Section 1-4.) 2. Remove the DC fan (front). (Refer to Section 2-5-1.) 3. Remove the four screws, and lift the sub frame assembly. 4. ...

[Page 60] Sony HDC1000

2-16 HDC1000/V1(E) Screws (M2) SDI 1 connector BNC bracket Washer Out side panel Coaxial cable Nut Hold the plug to remove. Do not attempt to remove by pulling the cable. OK NG 2-8-7. RET IN, TEST OUT Connector (CN-2620 Board) 1. Remove the MIC panel...

[Page 61] Sony HDC1000

2-17 HDC1000/V1(E) Nut Washers Screws (M2) Screws (M2) SDI 2/SDI connector BNC assembly CN3 CN-2620 board MIC panel assembly B3 x 8 B3 x 8 CN17 MB-1059 board Hot shoe assembly BUILD UP connector Screw of the connector 3. Disconnect the harness from ...

[Page 62] Sony HDC1000

2-18 HDC1000/V1(E) CN102 CP201 CP401 Harness clamps Harness clamp Coaxial cable (brown) Coaxial cable (green) Optical fiber cable (No.2) Optical fiber cable (No.1) 7. Remove the four screws, and remove the connector box. 8. Remove the four screws, an...

[Page 63] Sony HDC1000

2-19 HDC1000/V1(E) Optical fiber cable (No.2) CP401 Harness clamps CP201 Optical fiber cable (No.1) UL tape CN102 SDI-84/84C board 2-9-2. HDC1400/1500/1580 (Encapsulated Cable Assembly) 1. Remove the outside panel. (Refer to Section 1-4.) 2. Remove t...

[Page 64] Sony HDC1000

2-20 HDC1000/V1(E) 2-9-3. HDC1550 (TRIAX Assembly) 1. Remove the outside panel. (Refer to Section 1-4.) 2. Peel the UL tape off. 3. Remove the screw to detach the FL cover. 4. Remove the two screws, and lift the FL base up. 5. Disconnect the harness ...

[Page 65] Sony HDC1000

2-21 HDC1000/V1(E) 2-10-2. HDC1400/1500/1550/1580 w The DC/DC converter unit is a critical part for safety. If it is replaced with an unspecified part, a fire or electric shock may be caused. Be sure to use the specified DC/DC converter unit below fo...

[Page 66] Sony HDC1000

2-22 HDC1000/V1(E) 2-11. Replacing the Switching Regulator 2-11-1. HDC1000 w The switching regulator is a critical part for safety. If it is replaced with an unspecified part, a fire or electric shock may be caused. Be sure to use the specified switc...

[Page 67] Sony HDC1000

2-23 HDC1000/V1(E) B2.6 x 5 Poron sheets Thermattach tape (AC/DC) Switching regulator Power supply bracket 5. Remove the two screws to detach the power supply bracket from the switching regulator. m . There is the thermattach tape (AC/DC) between the...

[Page 68] Sony HDC1000

2-24 HDC1000/V1(E) B2.6 x 5 B2.6 x 5 Hanging band (REAR) Switching regulator B2.6 x 5 Connectors FL bracket Connectors B2.6 x 5 Poron sheets Thermattach tape (AC/DC) Switching regulator Power supply bracket 5. Remove the two screws to detach the powe...

[Page 69] Sony HDC1000

2-25 HDC1000/V1(E) OK NG Hold the plug to remove. Do not attempt to remove by pulling the cable. CN102 CN201 CN851 CP201 CP401 Harness clamp Harness clamp Coaxial cable (brown) Coaxial cable (green) Optical fiber cable Optical fiber cable SDI-84 b...

[Page 70] Sony HDC1000

2-26 HDC1000/V1(E) PSW3 x 6 B3 x 10 Coaxial cable (red) SDI unit assembly DPR-265 board CN601 Screws with stopper/ PSW3 x 6 PSW3 x 6 MB-1060 board CN28 CN29 CN4 CN9 Coaxial cable (orange) Coaxial cable (yellow) CN28 CN29 13. Release the harness from...

[Page 71] Sony HDC1000

2-27 HDC1000/V1(E) CN102 CP201 CP401 Harness clamps Harness clamp Coaxial cable (brown) Coaxial cable (green) Optical fiber cable (No.2) Optical fiber cable (No.1) SDI-84 board 18. Install the MB-1060 board by reversing the steps above. m . Arrange ...

[Page 72] Sony HDC1000

2-28 HDC1000/V1(E) 5. Disconnect the harnesses from the connectors (CN4, CN5) on the CN-2617 board. 6. Remove the two screws, and remove the CN-2617 board. 7. Install the CN-2617 board by reversing the steps above. B2 x 4 CN5 CN-2617 board CN4 2-13. ...

[Page 73] Sony HDC1000

2-29 HDC1000/V1(E) DC-DC converter unit AT-163 board AU-298 board DAP-33 board VDA-63 board 2-13-2. MB-1059 Board 1. Remove the inside panel and outside panel. (Refer to Section 1-4.) 2. Remove the front assembly. (Refer to Section 2-1.) 3. Draw all ...

[Page 74] Sony HDC1000

2-30 HDC1000/V1(E) 2-14. Checking SDI-84 Board (HDC1400/ 1500/1580) To check the operation of the SDI-84 board and to upgrade the PLD, perform preprocessing using the following procedure to ensure the service position for the SDI-84 board. 1. Remove ...

[Page 75] Sony HDC1000

3-1 HDC1000/V1(E) Section 3 Electrical Alignment When any board of HDC1000/1400/1500/1550/1580 is repaired or replaced, perform electrical adjustments as follows. HDC1000/1400/1500/1580 Section 3-1 to 3-5 HDC1550 Section 3-1 to 3-9 m . Perform video ...

[Page 76] Sony HDC1000

3-2 HDC1000/V1(E) Chart Illuminance meter Light source 3-1-4. Maintaining the Grayscale Chart For the adjustment, using an 89.9 %-reflective grayscale chart is preferable. If a reflective chart is not available, use a well-maintained pattern box and ...

[Page 77] Sony HDC1000

3-3 HDC1000/V1(E) Chart Luminance meter 1 m Setting luminous intensity (when the transparent chart is used) Equipment: Luminance meter (Minolta LS-110 or equivalent. Calibrated.) 1. Light the pattern box and warm up for about 30 minutes. 2. Place the...

[Page 78] Sony HDC1000

3-4 HDC1000/V1(E) How to change the setting values To enter or cancel the setting value of items, which can be changed by turning the MENU SELECT control (HDC1000) or rotary encoder (HDC1500/1550/1580), proceed as follows. HDC1000 To enter the settin...

[Page 79] Sony HDC1000

3-5 HDC1000/V1(E) 3-1-6. Connection of Equipment HDC1000 HDC1400/1500/1550 HDC1580 CCA-5 CABLE (max. 200 m) MASTER SETUP UNIT MSU-700A/750/900/950 Waveform monitor A-ch HDVF-700A HD CAMERA HDC1000 LENS REMOTESDI 1 Y, Pb, Pr R, G, B 1 Color monitor ...

[Page 80] Sony HDC1000

3-6 HDC1000/V1(E) When adjusting using the Setup menu . PAINT menu Page Setting item Initial setting SW STATUS FLARE ON GAMMA ON BLK GAM OFF KNEE OFF WHT CLIP OFF DETAIL ON LVL DEP ON SKIN DTL OFF MATRIX OFF VIDEO LEVEL TEST OFF Side panel (HDC1400/1...

[Page 81] Sony HDC1000

3-7 HDC1000/V1(E) 3-1-8. Adjustment Items and Setup Menu Items Refer to the following table when using the camera setup menu for electrical adjustments without using MSU-900. The table shows camera menu items corresponding to adjustment items of MSU-...

[Page 82] Sony HDC1000

3-8 HDC1000/V1(E) 3-2. Automatic Adjustment To execute the automatic adjustment 1. MSU menu operation: . MAINTENANCE button → ON (lit) . Touch panel operation [Auto|Setup] → [Auto|Level] n When performing automatic adjustment using the menu of th...

[Page 83] Sony HDC1000

3-9 HDC1000/V1(E) 3-3-2. BLACK SET Adjustment Preparation . Setting for MSU-900 CLOSE button → ON (lit) MASTER GAIN → 12 Adjustment Procedure 1. Adjustment Item: MENU: SERVICE PAGE: BLACK SHADING ITEM: BLK SET [R], [G], [B] Specification: Adjust ...

[Page 84] Sony HDC1000

3-10 HDC1000/V1(E) 3-3-4. V-SUB Adjustment Preparation . Setting for MSU-900 MASTER GAIN → 0 SHUTTER button → OFF (dark) . Display a high-brightness chart with a size of half the monitor frame, and release the iris. Adjustment Procedure 1. Adjust...

[Page 85] Sony HDC1000

3-11 HDC1000/V1(E) 3-3-5. BLACK SHADING Adjustment Preparation . Setting for MSU-900 CLOSE button → ON (lit) GAMMA OFF button → OFF (lit) MASTER GAIN → 12 MASTER BLACK → 30 Adjustment Procedure 1. Adjustment Item: MENU: SERVICE PAGE: BLACK SH...

[Page 86] Sony HDC1000

3-12 HDC1000/V1(E) (H SAW) (H PARA) (V SAW) (V PARA) Adjustment Procedure 1. Adjust the white balance. WHITE button/MSU-900 → ON (lit) 2. If the shading is monitored, proceed as follows. MSU menu operation: . MAINTENANCE button → ON (lit) . Touch...

[Page 87] Sony HDC1000

3-13 HDC1000/V1(E) 3-3-7. RPN Adjustment Preparation . Adjust the color monitor manually for better display condition. . Setting for MSU-900 CLOSE button → ON (lit) DETAIL button → OFF (lit) MASTER GAIN → 12 . Menu setting MENU: SERVICE PAGE: O...

[Page 88] Sony HDC1000

3-14 HDC1000/V1(E) H V Adjustment Procedure 1. MSU menu operation: . PAINT button → ON (lit) . Touch panel operation (Page 1/3) → [Detail] → [Detail|1] . Set each item as follows. Level → 99 Limiter → 0 Crispening → _25 Level Dep → 25 2...

[Page 89] Sony HDC1000

3-15 HDC1000/V1(E) A 3-4-2. Detail Level Adjustment Equipment: Waveform monitor (R, G, B) Test Point: SDI 1 connector (HDC1000/1500) SDI connector (HDC1400/1550) SDI 1 connector (HDCU1080) Object: Grayscale chart Preparations . Setting for MSU-900 DE...

[Page 90] Sony HDC1000

3-16 HDC1000/V1(E) Line select A 3-4-5. Detail Clip Adjustment Equipment: Waveform monitor (R, G, B) Test Point: SDI 1 connector (HDC1000/1500) SDI connector (HDC1400/1550) SDI 1 connector (HDCU1080) Object: Grayscale chart Preparations . Setting for...

[Page 91] Sony HDC1000

3-17 HDC1000/V1(E) C B 3. Adjust the white limiter. MSU menu operation: . PAINT button → ON (lit) . Touch panel operation (Page 1/3) → [Detail] → [Detail|3] Adjustment Item: W.Limiter Specification: Adjust the edge at portion B for the desired ...

[Page 92] Sony HDC1000

3-18 HDC1000/V1(E) B A 3-4-8. Flare Adjustment Equipment: Waveform monitor (R, G, B) Test Point: SDI 1 connector (HDC1000/1500) SDI connector (HDC1400/1550) SDI 1 connector (HDCU1080) Object: Grayscale chart Preparations . Setting for MSU-900 KNEE OF...

[Page 93] Sony HDC1000

3-19 HDC1000/V1(E) B A 3-4-9. Gamma Correction Adjustment Equipment: Waveform monitor (R, G, B) Test Point: SDI 1 connector (HDC1000/1500) SDI connector (HDC1400/1550) SDI 1 connector (HDCU1080) Object: Grayscale chart Preparations . Setting for MSU-...

[Page 94] Sony HDC1000

3-20 HDC1000/V1(E) A 3-4-11. White Clip Level Adjustment Equipment: Waveform monitor (R, G, B) Test Point: SDI 1 connector (HDC1000/1500) SDI connector (HDC1400/1550) SDI 1 connector (HDCU1080) Preparations . Setting for MSU-900 MASTER GAIN → +12 d...

[Page 95] Sony HDC1000

3-21 HDC1000/V1(E) 3-4-12. File Store After adjustments described in Section 3-4 are completed, be sure to execute the reference file store. 1. MSU menu operation: . FILE button → ON (lit) . Touch panel operation [Reference] → [Ref|Store] → [St...

[Page 96] Sony HDC1000

3-22 HDC1000/V1(E) OHB File Store 1. MSU menu operation: . FILE button → ON (lit) . Touch panel operation [OHB|File] → [OHB|Store] → [Store] 2. When the store operation is completed, the message “OHB File Stored” is displayed. Setting after...

[Page 97] Sony HDC1000

3-23 HDC1000/V1(E) 3-6. Adjustment Preparation of HDC1550 3-6-1. Equipment Required Measuring equipment . Oscilloscope: Tektronix 2465B or equivalent . Spectrum analyzer: Advantest R3131A or equivalent . Signal generator: Tektronix TSG130A or equival...

[Page 98] Sony HDC1000

3-24 HDC1000/V1(E) Signal generator TRIAX cable Optical fiber cable HDCU-950 RET1 CAMERA HDFX100 HDCU CAMERA/ HDTX HDC1550 HDCU/ HDFX 4. Connect the equipments as shown in the following figure. 3-6-3. Connection 1. Remove the two screws to detach the...

[Page 99] Sony HDC1000

3-25 HDC1000/V1(E) 3-7. TONE Adjustment (HDC1550) 3-7-1. CHU DATA/TONE Frequency Adjustment Preparation 1. Connect the oscilloscope to the spectrum analyzer as shown below. Adjustment procedure 2. Adjust the frequency at the waveform peak while chang...

[Page 100] Sony HDC1000

3-26 HDC1000/V1(E) 3-8. Video System Adjustment (HDC1550) n Be sure to perform “3-7. TONE Adjustment” before adjusting the video system. 3-8-1. Demodulation Tuning Adjustment Preparation 1. Set S601 and S605 for adjustment on the DTX-1 board in H...