XtendLan XL-ICA-106M2 User Manual

Download or browse on-line these Operation & User’s Manual for XtendLan XL-ICA-106M2 Security Camera.

XtendLan XL-ICA-106M2 Manual Information:

This manual for XtendLan XL-ICA-106M2, given in the PDF format, is available for free online viewing and download without logging on. The guide contains 34 pages, and the size of the file at download is . The document type is Operation & User’s Manual.

Download Manual

Summary of Contents:

[Page 1] XtendLan XL-ICA-106M2

XL-ICA-106M2 User’s Manual ...

[Page 2] XtendLan XL-ICA-106M2

Welcome Thank you for purchasing our IP camera! This user‟s manual is designed to be a reference tool for your system. Please read the following safeguards and warnings carefully before you use or install the IP camera. Important Saf...

[Page 3] XtendLan XL-ICA-106M2

Before installation, please open the package and check all the components are included: Contact your local retailer ASAP if something is missing in your package. Table of Contents 1 Overview .....................................................

[Page 4] XtendLan XL-ICA-106M2

8 Appendix 2 Function List ......................................................................................................... 28 9 Appendix 3 Device Factory Default Setup ........................................................................

[Page 5] XtendLan XL-ICA-106M2

1 Overview 1.1 General Introduction This series IP camera combines the traditional camera and network video technology together. It integrates video capture, video process, network transmission and storage. You can just connect it to the netwo...

[Page 6] XtendLan XL-ICA-106M2

Peripheral Equipment  Support peripheral equipment management, each peripheral equipment control protocol and interface can be set freely.  Support serial port(RS485) transparent data transmission Assistant Function  Support au...

[Page 7] XtendLan XL-ICA-106M2

2 Interface 2.1 Lens Besides the lens included in package, you can use other CS installation lens. Note: This series IP camera supports CS port only. You need to use a 5mm C/CS lens conversion ring if you want to use a C type lens. 2.1.1 ...

[Page 8] XtendLan XL-ICA-106M2

 Socket(not included in the package)  PIN 4:Driver-(ground)  PIN 2:Control+  PIN1:Control-  PIN 3:Driver+ 2.1.3 Lens Installation Please follow the steps listed below. See Figure...

[Page 9] XtendLan XL-ICA-106M2

Figure 2-4 2.2 Rear Panel Please refer to the following sheet and Figure 2-5 for IP camera interface information. Interface Name Connector Function VIDEO OUT Video output port BNC Output analog video signal. Can connect to ...

[Page 10] XtendLan XL-ICA-106M2

light flashes and then becomes on, which means application is running normally. Now you can log in via network.  The indication light becomes off when you reboot the system via software.  The green light flashes when system is...

[Page 11] XtendLan XL-ICA-106M2

when you connect the IP camera to the wireless network. A RS485 port I/O port RS485_A port, control external PTZ B RS485_B port, control external PTZ 1 1-2ch alarm Alarm input port 1. To receive the signal from the extern...

[Page 12] XtendLan XL-ICA-106M2

LEVEL Auto aperture adjustment button Adjust aperture level. AUDIO OUT Audio output 3.5mm JACK port. Output audio signal to the device such as sound box. AUDIO IN Audio input 3.5mm JACK port. Input audio signal. Rece...

[Page 13] XtendLan XL-ICA-106M2

swap card, please stop recording first. Figure 2-5 2.2.1 I/O Socket Operation Introduction First use small slotted screwdriver press the button in the cable slot, and then insert the cable into the slot. Finally release the ...

[Page 14] XtendLan XL-ICA-106M2

Figure 2-7 Please refer to Figure 2-8 for alarm output layout. Figure 2-8 ...

[Page 15] XtendLan XL-ICA-106M2

3 Installation 3.1 System Requirement This series IP camera has the following system requirement.  Processor Pentium 4, 1.5 GHz or higher(Pentium 4, 2.4 GHz or higher recommended )  RAM 256 MB or higher  OS Microsoft Win...

[Page 16] XtendLan XL-ICA-106M2

Figure 3-2 Note:  If you want to connect IP camera to the ADSL MODEM, you need to refer to the PPPoE setup section.  If there is more than one IP camera need to be connected, you need to set different IP addresses for each camera resp...

[Page 17] XtendLan XL-ICA-106M2

17 4 Auto Search IP Function Auto search IP tool allows you to search or modify IP camera current IP address. Open AutoSearchDevc.exe ( ), click device list item yo...

[Page 18] XtendLan XL-ICA-106M2

18 Figure 4-3 After you logged in, you can see an interface is shown as in Figure 4-4. Here you can modify device IP address, sub-net mask and gateway information. ...

[Page 19] XtendLan XL-ICA-106M2

19 5 Network Safety Level Setup You need to modify your IE security setup if you can not install controls properly. Open your IE browser, Tools->Internet Options...

[Page 20] XtendLan XL-ICA-106M2

20 Figure 5-2 Then system goes back to Figure 5-1, click “sites” button, system pops up the following dialogue box. See Figure 5-3. Figure 5-3 Click advance...

[Page 21] XtendLan XL-ICA-106M2

21 Figure 5-4 ...

[Page 22] XtendLan XL-ICA-106M2

22 6 Client Operation IP camera factory default setup:  IP address: 192.168.1.108.  User name: admin  Password: admin 6.1 Network Connection Pleas...

[Page 23] XtendLan XL-ICA-106M2

23 If you can‟t download the ActiveX file, please modify your settings as follows. See Figure 6-2. Figure 6-2 After installation, the interface is shown as bel...

[Page 24] XtendLan XL-ICA-106M2

24 After you logged in, you can see the main window. See Figure 6-6. This main window can be divided into the following sections.  Section 1: there are five fu...

[Page 25] XtendLan XL-ICA-106M2

25 Figure 6-6 Please refer to the web operation manual for detailed information. Note: Slight difference may be found in user interface. All the designs and soft...

[Page 26] XtendLan XL-ICA-106M2

26 7 Appendix 1 Specification Specification Index Note Video Standard Supported PAL : 25f/s NTSC: 30f/s Encode capacity One D1 + one CIF or O...

[Page 27] XtendLan XL-ICA-106M2

27 Weight ...

[Page 28] XtendLan XL-ICA-106M2

28 8 Appendix 2 Function List Specification Note Lens Control Zoom Adjustment Manual Focus Adjustment Manual Aperture Adjustment Auto /manual D...

[Page 29] XtendLan XL-ICA-106M2

29 or not, system just begins recording. Alarm Record System automatically enables recording function when alarm occurred. Motion Detection Record When in...

[Page 30] XtendLan XL-ICA-106M2

30 setup, alarm setup, OSD information. Search log, status, user management, email setup, data modification, program upgrade, reboot and etc. IPC provides inte...

[Page 31] XtendLan XL-ICA-106M2

31 9 Appendix 3 Device Factory Default Setup Function Configuration Type Item Name Default setup General Setup Date format Y-M-D Date separator ...

[Page 32] XtendLan XL-ICA-106M2

32 IP address 192.168.1.108 Subnet mask 255.255.0.0 Gateway 192.168.0.1 Device name Device factory default name TCP port 37777 HTTP port 80 ...

[Page 33] XtendLan XL-ICA-106M2

33 Snapshot Disable PTZ Setup Channel Ch01 Protocol EPTZ Address 1 Baud rate 115200 Data bit 8 Stop bit 1 Parity None Default ...

[Page 34] XtendLan XL-ICA-106M2

34 10 Appendix 4 FAQ Question Fix Device can not boot normally Press RESET button for at least 20 seconds to restore factory default setup. SD card hot ...