Circutor CPM M80430 Instruction Manual

[Page 1] Circutor CPM M80430

MULTIMETER CURRENT CLAMP CPM (Code: M80430) INSTRUCTION MANUAL ( M98111201-03-10A )    CIRCUTOR S.A. ...

[Page 2] Circutor CPM M80430

--------- MULTIMETER CURRENT CLAMP CPM -------- PG No. 1 - CPM ANALYZER INDEX page no. SAFETY NOTES Before using the equipment please read the user manual, paying special attention to the SAFETY REQUIREMENTS s...

[Page 3] Circutor CPM M80430

--------- MULTIMETER CURRENT CLAMP CPM -------- PG No. 2 - The analyzer is powered by a 9 V battery. Its design and its double insulation makes the CPM a robust and secure instrument. ...

[Page 4] Circutor CPM M80430

--------- MULTIMETER CURRENT CLAMP CPM -------- PG No. 3 - 1.2.- Specifications Display 3 ½ digit LCD display with a maximum reading of 1999. Display functions Hold MAX Measurement value hold. Maximum measureme...

[Page 5] Circutor CPM M80430

--------- MULTIMETER CURRENT CLAMP CPM -------- PG No. 4 - Power Supply 9 V, IEC 6F22 battery. Battery life Typically 200 hours for a zinc-carbon battery Environmental conditions Operating temperature Storage temperature ...

[Page 6] Circutor CPM M80430

--------- MULTIMETER CURRENT CLAMP CPM -------- PG No. 5 - DC Voltage Range Accuracy Input impedance Overload protection 600 V ± (0.5% read. + 1 digit) 10 MΩ 600 V DC or AC rms AC Voltage (50-500 Hz) Ranges...

[Page 7] Circutor CPM M80430

--------- MULTIMETER CURRENT CLAMP CPM -------- PG No. 6 - Continuity Sound alarm Overload protection Less than 30Ω in the range of 2kΩ. 600 V DC or AC rms Diode test Test current Accuracy Open circuit tens...

[Page 8] Circutor CPM M80430

--------- MULTIMETER CURRENT CLAMP CPM -------- PG No. 7 - 700 A AC Max. during 1 minute. ...

[Page 9] Circutor CPM M80430

--------- MULTIMETER CURRENT CLAMP CPM -------- PG No. 8 - 2.- SAFETY REQUIREMENTS 2.1.- General  This equipment can be used in environments of Pollution Degree 2. Overvoltage Category: See sections 2.2 and 2.3.  In...

[Page 10] Circutor CPM M80430

--------- MULTIMETER CURRENT CLAMP CPM -------- PG No. 9 - Symbols: The analyzer is protected by double or reinforced insulation. Caution! Risk of electric shock. Caution! See this manual before using the analyzer. Fuse ...

[Page 11] Circutor CPM M80430

--------- MULTIMETER CURRENT CLAMP CPM -------- PG No. 10 - 2.2.- Special precautions  This equipment can be used for Overvoltage Category II installations. The clamp can be used exclusively for the measurement of current for...

[Page 12] Circutor CPM M80430

--------- MULTIMETER CURRENT CLAMP CPM -------- PG No. 11 - 3.- INSTRUCTIONS FOR USE 3.1.- Description of controls and elements A B ...

[Page 13] Circutor CPM M80430

--------- MULTIMETER CURRENT CLAMP CPM -------- PG No. 12 - [1] Rotary function switch Analyzer off DC voltage measurement, range 600 V DC current measurement, range 700 A DC current measurement, range 200 A Resist...

[Page 14] Circutor CPM M80430

--------- MULTIMETER CURRENT CLAMP CPM -------- PG No. 13 - [3] V input terminal for AC/DC voltage measurement [4] COM common input terminal for test probes for all measurements. [5] Input terminal for resistance measuremen...

[Page 15] Circutor CPM M80430

--------- MULTIMETER CURRENT CLAMP CPM -------- PG No. 14 - 3.2.- Use ATTENTION When the value to be measured is unknown always place the rotary switch to the highest range and reduce it progressively in function of the valu...

[Page 16] Circutor CPM M80430

--------- MULTIMETER CURRENT CLAMP CPM -------- PG No. 15 - 3.2.2.- Current measurement 1. Set the rotary switch [1] to the desired higher range 700 A (AC or DC). In DC current measurement mode use the DCA ZERO button [2] to del...

[Page 17] Circutor CPM M80430

--------- MULTIMETER CURRENT CLAMP CPM -------- PG No. 16 - 3.2.4.- Frequency measurement 1. Set the rotary switch [1] to the Hz position. 2. Connect the red test probe to the terminal [5] and the black test probe to the COM t...

[Page 18] Circutor CPM M80430

--------- MULTIMETER CURRENT CLAMP CPM -------- PG No. 17 - 3.2.6.- Diode test 1. Connect the black test probe to the COM terminal [4] and the red test probe to the terminal [5]. 2. Set the rotary switch [1] to the position �...

[Page 19] Circutor CPM M80430

--------- MULTIMETER CURRENT CLAMP CPM -------- PG No. 18 - 4.- MAINTENANCE Attention : Disconnect the test probes before changing the battery or performing any maintenance service. 4.1.- Battery replacement When the sy...

[Page 20] Circutor CPM M80430

--------- MULTIMETER CURRENT CLAMP CPM -------- PG No. 19 - Caution : Do not use aromatic hydrocarbons or chlorinated solvents for cleaning. These products can attack the materials used to make the case. Clean the case peri...