Nortel 1110 User Manual

Download or browse on-line these Fundamentals for Nortel IP Phone 1110 Conference Phone, Cordless Telephone.

Nortel IP Phone 1110 Manual Information:

This manual for Nortel IP Phone 1110, given in the PDF format, is available for free online viewing and download without logging on. The guide contains 560 pages, and the size of the file at download is . The document type is Fundamentals.

Download Manual

This sample of Nortel IP Phone 1110 Manual is aimed at the following devices list: 2033, IP Phone 1110, 1140E, 1150E, 2050

More Manuals:

In case you failed to obtain relevant information in this document, please, look through related operating manuals and user instructions for Nortel IP Phone 1110. Just click one of the links below to go to the selected manual:

Summary of Contents:

[Page 1] Nortel IP Phone 1110

Nortel Communication Server 1000 IP Phones Fundamentals NN43001-368 . ...

[Page 2] Nortel IP Phone 1110

Document status: Standard Document version: 01.02 Document date: 20 June 2007 Copyright © 2003–2007, Nortel Networks All Rights Reserved. Sourced in Canada. The information in this document is subject to change without notice. The statements, con�...

[Page 3] Nortel IP Phone 1110

3 Revision histor y June 2007 Standard 01.02. This document is up-issued to support Communication Server 1000 Release 5.0. This document contains an update due to CR Q01584230, CR Q01642379, CR Q01656411, and CR Q01647741. It also contains an update ...

[Page 4] Nortel IP Phone 1110

4 Revision history October 2006 Standard 18.00. This document is up-issued to support the addition of the IP Phone 1150E. August 2006 Standard 17.00. This document is up-issued to include updated technical content due to CR Q01434634. July 2006 Stand...

[Page 5] Nortel IP Phone 1110

Revision history 5 April 2005 Standard 6.00. This document is up-issued to support the addition of the IP Phone 2007. April 2005 Standard 5.00. This document is up-issued to support the addition of the IP Audio Conference Phone 2033. February 2005 St...

[Page 6] Nortel IP Phone 1110

6 Revision history Nortel Communication Server 1000 IP Phones Fundamentals NN43001-368 01.02 Standard Release 5.0 20 June 2007 Copyright © 2003–2007, Nortel Networks . ...

[Page 7] Nortel IP Phone 1110

7 Contents How to get Help 23 Getting help from the Nortel Web site 23 Getting help over the phone from a Nortel Solutions Center 23 Getting help from a specialist by using an Express Routing Code 23 Getting help through a Nortel distributor or resel...

[Page 8] Nortel IP Phone 1110

8 Contents Components and functions 65 Keys and functions 65 Services menu 67 Supported features 68 Features not currently supported 70 Display characteristics 70 Cleaning the IP Phone display screen 71 Programmable line (DN)/feature key label displa...

[Page 9] Nortel IP Phone 1110

Contents 9 First-time installation 110 Configuring the IP Phone 2004 110 Startup sequence 113 Full Duplex mode 130 Gratuitous Address Resolution Protocol Protection 131 Extensible Authentication Protocol 132 Redeploying an IP Phone 2004 132 Replacin...

[Page 10] Nortel IP Phone 1110

10 Contents Services menu 172 Local Tools menu 173 Supported features 174 Features not currently supported 176 Touch panel 176 Calibrate the touch panel 177 Stylus 177 Dialpad entry 177 Cleaning the IP Phone display screen 178 Display characteristics...

[Page 11] Nortel IP Phone 1110

Contents 11 Firmware 212 Nor tel IP Softphone 2050 213 Contents 213 Introduction 213 Description 214 Supported features 215 Language support 216 Components 216 Call Control window 216 Operation 219 Display characteristics 219 Nortel USB Audio Kit 220...

[Page 12] Nortel IP Phone 1110

12 Contents System requirements 242 Supported features 242 Application software 243 ClearType 244 MVC 2050 components 244 Compatible PDAs 244 Headsets 244 Automatic Gain Control and feedback 244 Audio quality 245 MVC 2050 Call Handling screen 245 Dis...

[Page 13] Nortel IP Phone 1110

Contents 13 Local Tools menu password protection 271 Configuring Secure Local Menu through Full DHCP 272 Accessing the Local Tools menu 273 Key number assignments 273 Package components 274 Installation and configuration 275 Before you begin 275 Fi...

[Page 14] Nortel IP Phone 1110

14 Contents Installing the IP Phone 1120E 323 Full Duplex mode 332 TFTP firmware upgrade 334 Gratuitous Address Resolution Protocol Protection 335 Extensible Authentication Protocol 335 Redeploying an IP Phone 1120E 335 Replacing an IP Phone 1120E 3...

[Page 15] Nortel IP Phone 1110

Contents 15 Nor tel IP Phone 1150E 375 Contents 375 Introduction 376 Description 376 Components and functions 378 Services menu 382 Local Tools menu 383 Supported features 384 Features not currently supported 387 Display characteristics 387 Self-labe...

[Page 16] Nortel IP Phone 1110

16 Contents Package components 419 Configuration 419 Installation 420 Expansion Module startup initialization 424 Operating parameters 425 IP Phone 1120E 425 IP Phone 1140E and IP Phone 1150E 425 Services key operation 426 Display diagnostics 426 Fi...

[Page 17] Nortel IP Phone 1110

Contents 17 Three-port switch support 449 VLAN IDs 450 Automatic VOICE VLAN ID configuration 450 Enhanced VLAN Tagging 451 Enhanced DATA VLAN 452 Appendix C 802.1x Port-based network access control 455 Contents 455 Introduction 455 Extensible Authen...

[Page 18] Nortel IP Phone 1110

18 Contents Pairing your headset 523 Appendix H Language enhancement 531 Contents 531 Description 531 UTF-8 character encoding 531 TFTP Server support 532 Synchronizing the language 532 Expansion Module for IP Phone 1100 Series font support 532 Appen...

[Page 19] Nortel IP Phone 1110

Contents 19 Procedure 20 Enabling Full Duplex mode 130 Procedure 21 Checking Ethernet Statistics 131 Procedure 22 Changing the TN of an existing IP Phone 2004 132 Procedure 23 Replacing an IP Phone 2004 133 Procedure 24 Removing an IP Phone 2004 from...

[Page 20] Nortel IP Phone 1110

20 Contents Procedure 62 Changing the TN of an existing IP Phone 1110 300 Procedure 63 Replacing an IP Phone 1110 301 Procedure 64 Removing an IP Phone 1110 from service 302 Procedure 65 Configuring the IP Phone 1120E 318 Procedure 66 Installing the...

[Page 21] Nortel IP Phone 1110

Contents 21 Procedure 109 Tracing a route 480 Procedure 110 Reviewing the results of the trace 480 Procedure 111 Browsing Ethernet Statistics 481 Procedure 112 Checking 802.1x Supplicant status 481 Procedure 113 Checking 802.1x Supplicant Authenticat...

[Page 22] Nortel IP Phone 1110

22 Contents Nortel Communication Server 1000 IP Phones Fundamentals NN43001-368 01.02 Standard Release 5.0 20 June 2007 Copyright © 2003–2007, Nortel Networks . ...

[Page 23] Nortel IP Phone 1110

23 How to get Help This chapter explains how to get help for Nortel products and services. Getting help from the Nortel Web site The best way to get technical support for Nortel products is from the Nortel Technical Support Web site: w ww . nortel.co...

[Page 24] Nortel IP Phone 1110

24 How to get Help www.nortel.com/erc Getting help through a Nortel distributor or reseller If you purchased a service contract for your Nortel product from a distributor or authorized reseller, contact the technical support staff for that distributo...

[Page 25] Nortel IP Phone 1110

25 New in this Release The following sections detail what is new in IP Phones Fundamentals (NN43001-368) for CS 1000 Release 5.0. Features See the following sections for information about feature changes: • "Live Dialpad" (page 25) • &q...

[Page 26] Nortel IP Phone 1110

26 New in this release Unique TN Types for existing IP Phones The names of existing IP Phone TN types have a new IP Phone naming convention. Table 1 "CS 1000 Release 5.0 TN type naming convention" (page 26) shows the unique IP Phone TN type...

[Page 27] Nortel IP Phone 1110

Subject 27 • IP Phone 1120E • IP Phone 1140E • IP Phone 1150E With the appropriate downloaded fonts, the IP Phone supports the following languages: • Arabic • Simplified Chinese • Traditional Chinese • Hebrew • Japanese • Korean Fo...

[Page 28] Nortel IP Phone 1110

28 New in this release Note on legacy products and releases This NTP contains information about systems, components, and features that are compatible with Nortel Communication Server 1000 Release 5.0 software. For more information about legacy produc...

[Page 29] Nortel IP Phone 1110

Subject 29 Online To access Nortel documentation online, click the Technical Documentation link under Support on the Nortel home page: w ww.nortel.com CD-ROM To obtain Nortel documentation on CD-ROM, contact your Nortel customer representative. Norte...

[Page 30] Nortel IP Phone 1110

30 New in this release Nortel Communication Server 1000 IP Phones Fundamentals NN43001-368 01.02 Standard Release 5.0 20 June 2007 Copyright © 2003–2007, Nortel Networks . ...

[Page 31] Nortel IP Phone 1110

31 Nortel IP Phone 2001 Contents This section contains the following topics: • "Introduction" (page 31) • "Description" (page 32) • "Components and functions" (page 33) • "Supported features" (page 34) ...

[Page 32] Nortel IP Phone 1110

32 Nortel IP Phone 2001 • Procedure 3 "Installing an IP Phone 2001 for the first time using DHCP" (page 51) • Procedure 4 "Enabling Full Duplex mode" (page 58) • Procedure 5 "Checking Ethernet Statistics" (page 59...

[Page 33] Nortel IP Phone 1110

Components and functions 33 Components and functions This section describes the following components and functions of the IP Phone 2001: • keys and functions • Services menu Keys and functions Table 2 "IP Phone 2001 keys and functions" ...

[Page 34] Nortel IP Phone 1110

34 Nortel IP Phone 2001 Services menu Table 3 "Services menu" (page 34) shows the Services menu. Table 3 Services menu Services key Press the Services key to access the following items: • Telephone Options — Volume adjustment — Contra...

[Page 35] Nortel IP Phone 1110

Supported features 35 Functions for the context-sensitive soft keys are configured in LD 11. • volume control bar to adjust ringer, speaker, handset, and headset volume • two specialized feature keys — Message/Inbox — Services • two call-p...

[Page 36] Nortel IP Phone 1110

36 Nortel IP Phone 2001 For more information about 802.1x port-based network access control, see Appendix "802.1x Port-based network access control" (page 455). • integrated hardware to support Power over Ethernet (PoE) for IEEE 802.3af P...

[Page 37] Nortel IP Phone 1110

Display characteristics 37 Figure 2 IP Phone 2001 display areas Cleaning the IP Phone display screen Gently wipe the IP Phone display screen with a soft, dry cloth. CAUTION Use no any liquids or powders on the IP Phone 2001. Using anything other than...

[Page 38] Nortel IP Phone 1110

38 Nortel IP Phone 2001 to On. The icon remains in the on state until the feature key is pressed again. This cancels the enabled feature and turns the icon off, and returns the soft key label to its original state. Use the More soft key to navigate t...

[Page 39] Nortel IP Phone 1110

Package components 39 Table 4 "IP Phone 2001 components list" (page 39) lists the IP Phone 2001 package components and product codes. Table 4 IP Phone 2001 components list IP Phone 2001 package contents include • IP Phone 2001 • handset...

[Page 40] Nortel IP Phone 1110

40 Nortel IP Phone 2001 Power transformer 2-prong wall plug direct plug-in AC to AC, 8 W, 240 VAC, 50 Hz, to 16 VAC at 500 mA (Australia and New Zealand) A0647042 Power transformer AC to AC, direct plug-in, 8 W, 100 VAC, 50 Hz, to 16 VAC at 500 mA A0...

[Page 41] Nortel IP Phone 1110

Installation and configuration 41 First-time installation You must first install an IP telephony node with the Communication Server. For information about installing an IP telephony node, see Signaling Server Installation and Commissioning (NN43001...

[Page 42] Nortel IP Phone 1110

42 Nortel IP Phone 2001 adapter jack in the bottom of the phone. Form a small bend in the cable and then thread the adapter cord through the channels in the stand. 6 Secure the IP Phone footstand to the base of the IP Phone. Use the angle adjustment ...

[Page 43] Nortel IP Phone 1110

Installation and configuration 43 8 Use Procedure 2 "Installing the IP Phone 2001 for the first time using manual configuration" (page 44) to install the IP Phone 2001 for the first time using manual configuration, or use Procedure 3 &...

[Page 44] Nortel IP Phone 1110

44 Nortel IP Phone 2001 Installing the IP Phone 2001 To install the IP Phone 2001 for the first time using manual configuration, use Procedure 2 "Installing the IP Phone 2001 for the first time using manual configuration" (page 44). To ...

[Page 45] Nortel IP Phone 1110

Installation and configuration 45 4 At the prompt, LLDP Enable?, enter 1-Y (1 for Yes, default) to enable the ability to control 802.1Q and 802.1p bits. For more information about LLDP, see Appendix "802.1ab Link Layer Discovery Protocol" ...

[Page 46] Nortel IP Phone 1110

46 Nortel IP Phone 2001 S1 action Choose one of the following: • for TPS only, enter 1 • for TPS and Secure Media Controller, enter 6 or 1 For more information about Secure Media Controller, see Secure Multimedia Controller Implementation Guide (...

[Page 47] Nortel IP Phone 1110

Installation and configuration 47 S2 PK To manually configure the PK, set the Action Byte to 6. After you enter the PK, apply the changes and then change the Action Byte to 1, if required. Default is ffffffffffffffff. The Private key of the alternat...

[Page 48] Nortel IP Phone 1110

48 Nortel IP Phone 2001 Data VLAN? (0-N, 1-Y) Default 0 (for No). VLAN settings on the PC port of the IP Phone 2001 is used for the initial DHCP discovery and not for PC traffic, because the IP Phone 2001 does not have a PC port. Voice VLAN? (0-N, 1-...

[Page 49] Nortel IP Phone 1110

Installation and configuration 49 VLANFILTER (0-N, 1-Y) Default 0 (for No). You are not prompted for VLANFILTER if VLAN is not enabled. Ctrl pBits (0-7, 8-Au) Default 8 (for Auto). You are not prompted for Ctrl pBits if 802.1Q is not enabled. Media ...

[Page 50] Nortel IP Phone 1110

50 Nortel IP Phone 2001 The Enhanced UNIStim firmware download is supported on CS 1000 Release 4.5 or later. The Enhanced UNIStim firmware download feature for IP Phones improves the delivery of new firmware to IP Phones. For further information a...

[Page 51] Nortel IP Phone 1110

Installation and configuration 51 ATTENTION Timing information There are only four seconds between plugging in the IP Phone 2001 power transformer and the appearance of the Nortel logo in the middle of the display. When you see the logo, you have 1 ...

[Page 52] Nortel IP Phone 1110

52 Nortel IP Phone 2001 By default, Full DHCP is configured on the IP Phone 2001. Depending on the configuration requirements, you can change the IP Phone 2001 configuration to allow the following IP address assignments: • Static—enter all par...

[Page 53] Nortel IP Phone 1110

Installation and configuration 53 b. If you select Partial DHCP, then you must enter the following parameters: Screen prompt Description S1 IP The primary CS 1000 node IP address for the IP Phone 2001. S1 Port This is a fixed value: 4100. S1 action ...

[Page 54] Nortel IP Phone 1110

54 Nortel IP Phone 2001 Screen prompt Description S2 action Same as S1. You are not prompted for S2 PK if the S2 action is set to 1. S2 retry count Same as S1. S2 PK To manually configure the PK, set the Action Byte to 6. After you enter the PK, appl...

[Page 55] Nortel IP Phone 1110

Installation and configuration 55 8 Enter the following parameters: 802.1Q (0-No, 1-Yes) Default 1 (for Yes). You are not prompted for 802.1Q if LLDP is not enabled. Data VLAN? (0-N, 1-Y) Default 0 (for No). VLAN settings on the PC port of the IP Ph...

[Page 56] Nortel IP Phone 1110

56 Nortel IP Phone 2001 DHCP (0-No, 1-Yes) Default 0 (for No). If you select 1 (1 for Yes), the VLAN ID is configured automatically to a value received from the DHCP server. You are not prompted for DHCP if VLAN is not set to Auto (2-Au), or if DHCP ...

[Page 57] Nortel IP Phone 1110

Installation and configuration 57 For Succession Release 3.0 and CS 1000 Release 4.0, the IP Phone 2001 searches for the TFTP Server for firmware upgrade. If the file name specified in i2001.cfg is not the same as the current firmware, the IP Ph...

[Page 58] Nortel IP Phone 1110

58 Nortel IP Phone 2001 —End— Full Duplex mode In the Configuration menu, autonegotiate mode is the default setting for initial startup. Nortel recommends that autonegotiate mode is used on the network and the IP Phone. Use Full Duplex mode only...

[Page 59] Nortel IP Phone 1110

Gratuitous Address Resolution Protocol Protection 59 7 Restart the IP Phone 2001. The firmware settings are read and are applied to UPLINK and the PC Ethernet Port. —End— When the IP Phone restarts, the firmware reads the setting for Full Duple...

[Page 60] Nortel IP Phone 1110

60 Nortel IP Phone 2001 To enable GARP Protection during configuration, see Procedure 2 "Installing the IP Phone 2001 for the first time using manual configuration" (page 44) or Procedure 3 "Installing an IP Phone 2001 for the firs...

[Page 61] Nortel IP Phone 1110

Removing an IP Phone 2001 from service 61 To obtain the password, enter the nodePwdShow command in Element Manager. For further information, see Element Manager System Reference—Administration (NN43001-632). 5 Select the Clear soft key to clear the...

[Page 62] Nortel IP Phone 1110

62 Nortel IP Phone 2001 If the IP Phone 2001 was automatically configured, the DHCP lease expires and the IP address returns to the available pool. 2 In LD 11, enter OUT at the TN prompt. —End— Nortel Communication Server 1000 IP Phones Fundamen...

[Page 63] Nortel IP Phone 1110

63 Nortel IP Phone 2002 Contents This section contains the following topics: • "Introduction" (page 63) • "Description" (page 64) • "Components and functions" (page 65) • "Supported features" (page 68) ...

[Page 64] Nortel IP Phone 1110

64 Nortel IP Phone 2002 • Procedure 11 "Installing an IP Phone 2002 for the first time using DHCP" (page 86). • Procedure 12 "Enabling Full Duplex mode" (page 94). • Procedure 13 "Checking Ethernet Statistics" (pa...

[Page 65] Nortel IP Phone 1110

Components and functions 65 Figure 4 IP Phone 2002 Components and functions This section describes the following components and functions of the IP Phone 2002: • keys and functions • Services menu Keys and functions Table 6 "IP Phone 2002 ke...

[Page 66] Nortel IP Phone 1110

66 Nortel IP Phone 2002 Key Function Programmable line (DN)/feature keys (self-labeled) Programmable line (DN)/feature keys (self-labeled) are configured for various features on the IP Phone. One must be the prime DN key. A steady LCD light beside a ...

[Page 67] Nortel IP Phone 1110

Components and functions 67 Key Function Volume control bar Use the volume control bar to adjust the volume of the handset, headset, speaker, ringer, and, Handsfree feature. Press the right side of the rocker bar to increase volume; press the left si...

[Page 68] Nortel IP Phone 1110

68 Nortel IP Phone 2002 • Test Local Mode and Resume Local Mode (if Branch Office is configured) Double-press the Services key to access Network diagnostic utilities. For more information about Network diagnostic utilities, see Appendix "IP Ph...

[Page 69] Nortel IP Phone 1110

Supported features 69 • Corporate Directory • Personal Directory • Redial List • Callers List • Password Administration • Virtual Office • Branch Office • Active Call Failover • Enhanced UNIStim Firmware Download • Live Dialpad ...

[Page 70] Nortel IP Phone 1110

70 Nortel IP Phone 2002 • 802.1x Port-based network access control, industry standards to pass Extensible Authentication Protocol (EAP) over a LAN For more information about 802.1x port-based network access control, see Appendix "802.1x Port-b...

[Page 71] Nortel IP Phone 1110

Display characteristics 71 Figure 5 IP Phone 2002 display areas Cleaning the IP Phone display screen Gently wipe the IP Phone display screen with a soft, dry cloth. CAUTION Use no any liquids or powders on the IP Phone. Using anything other than a so...

[Page 72] Nortel IP Phone 1110

72 Nortel IP Phone 2002 The information in the display area changes, according to the call-processing state and active features. Because the IP Phone 2002 only has a one-line information display area, you are prompted to scroll through any additional...

[Page 73] Nortel IP Phone 1110

Package components 73 Package components The following information applies to Phase II IP Phones. Product codes for Phase II IP Phones are different from previous sets. See the product code on the back of the phone to confirm whether it is a Phase I...

[Page 74] Nortel IP Phone 1110

74 Nortel IP Phone 2002 Handset, Charcoal A0758634 Handset cord, Ethergray A0897725 Handset cord, Charcoal N0000763 Footstand, Charcoal (used for Ethergray and Charcoal models) A0891619 IP Phone 2001/2002/2004 Power Adaptors Power transformer (117/12...

[Page 75] Nortel IP Phone 1110

Installation and configuration 75 • Ensure 1 Software License exists 1 for each IP Phone 2002 being installed. • Ensure the host Call Server is equipped with a Signaling Server that runs the Line Terminal Proxy Server (LTPS) application. • If ...

[Page 76] Nortel IP Phone 1110

76 Nortel IP Phone 2002 b. Connect the other end of the handset cord to the handset. 4 Choose one of the following connections: • For an IP Phone not sharing LAN access with a PC: Connect one end of the CAT5 Ethernet cable to the network interface ...

[Page 77] Nortel IP Phone 1110

Installation and configuration 77 5 Connect the AC power adapter (optional). Leave the AC adapter unplugged from the power outlet, connect the adapter to the AC adapter jack in the bottom of the phone. Form a small bend in the cable and then thread ...

[Page 78] Nortel IP Phone 1110

78 Nortel IP Phone 2002 See Table 9 "IP Phone 2002 IP parameters" (page 78) for a summary of the IP parameters and how they are obtained. Table 9 IP Phone 2002 IP parameters Parameter Method of Acquisition VLAN ID Manually entered or automa...

[Page 79] Nortel IP Phone 1110

Installation and configuration 79 • Clear—clear an entire configuration entry • Cancel—cancels network configuration. The IP Phone reboots without saving changes. Procedure 10 Installing the IP Phone 2002 for the first time using manual c...

[Page 80] Nortel IP Phone 1110

80 Nortel IP Phone 2002 6 Enter the following information: Screen prompt Description set IP A valid IP Phone 2002 IP address. net msk A subnet mask. def gw The default Gateway for the IP Phone 2002 on the LAN segment to which it connects. 7 Enter the...

[Page 81] Nortel IP Phone 1110

Installation and configuration 81 Screen prompt Description To enter ALPHA digits A to F, enter the following: #1 = A #2 = B #3 = C #4 = D #5 = E #6 = F S2 IP The secondary CS 1000 node IP address for the IP Phone 2002. S2 Port Same as S1. S2 action...

[Page 82] Nortel IP Phone 1110

82 Nortel IP Phone 2002 Screen prompt Description Speed (0-A, 1-10, 2-100) Network interface port speed. Default 0 (for Auto) 0 = Auto 1 = 10 BT 2 = 100 BT You are not prompted for Speed if PC Port is set to 0 for Off. Duplex (0-A, 1-F, 2-H) Default ...

[Page 83] Nortel IP Phone 1110

Installation and configuration 83 Screen prompt Description LLDP VLAN? (0-No, 1-Yes) If you select 1 (1 for Yes), VLAN ID is configured automatically to the value received in the VLAN NAME TLV. You are not prompted for LLDP VLAN if VLAN is not set t...

[Page 84] Nortel IP Phone 1110

84 Nortel IP Phone 2002 Screen prompt Description Data VLAN? (0-N, 1-Y) Default 0 (for No). You are not prompted for Data VLAN if PC port is set to 0 for Off. Data VLAN Cfg? (0-Auto, 1-Man) Default 1 (for Man). You are not prompted for Data VLAN Cfg ...

[Page 85] Nortel IP Phone 1110

Installation and configuration 85 the IP Phone downloads the file and upgrades the firmware. This takes several minutes. When the upgrade is complete, the IP Phone 2002 reboots. For further information about TFTP Server configuration, see Appendi...

[Page 86] Nortel IP Phone 1110

86 Nortel IP Phone 2002 ATTENTION Timing information There are only 4 seconds between plugging in the IP Phone 2002 power transformer and the appearance of the Nortel logo in the middle of the display. When you see the logo, you have 1 second to resp...

[Page 87] Nortel IP Phone 1110

Installation and configuration 87 By default, Full DHCP is configured on the IP Phone 2002. Depending on the configuration requirements, you can change the IP Phone 2002 configuration to allow the following IP address assignments: • Static—en...

[Page 88] Nortel IP Phone 1110

88 Nortel IP Phone 2002 b. If you select Partial DHCP, then you must enter the following parameters: Screen prompt Description S1 IP The primary CS 1000 node IP address for the IP Phone 2002. S1 Port This is a fixed value: 4100. S1 action Choose one ...

[Page 89] Nortel IP Phone 1110

Installation and configuration 89 Screen prompt Description S2 Port Same as S1. S2 action Same as S1. You are not prompted for S2 PK if S2 Action is set to 1. S2 retry count Same as S1. S2 PK To manually configure the PK, set the Action Byte to 6. A...

[Page 90] Nortel IP Phone 1110

90 Nortel IP Phone 2002 Screen prompt Description You are not prompted for Duplex if PC Port is set to 0 for Off or if Speed is set to 0 for Auto. 8 Enter the following parameters: Screen prompt Description 802.1Q (0-No, 1-Yes) Default 1 (for Yes). Y...

[Page 91] Nortel IP Phone 1110

Installation and configuration 91 Screen prompt Description DHCP (0-No, 1-Yes) Default 0 (for No). If you select 1 (1 for Yes), the VLAN ID is configured automatically to a value received from the DHCP server. You are not prompted for DHCP if VLAN i...

[Page 92] Nortel IP Phone 1110

92 Nortel IP Phone 2002 Screen prompt Description Data VLAN Cfg? (0-Auto, 1-Man) Default 1 (for Man) You are not prompted for Data VLAN Cfg if LLDP or Data VLAN are not enabled and PC Port is set to 0 for Off. If you select 0 (for Auto), VLAN ID is a...

[Page 93] Nortel IP Phone 1110

Installation and configuration 93 The Enhanced UNIStim firmware download is supported on CS 1000 Release 4.5 or later. The Enhanced UNIStim firmware download feature for IP Phones improves the delivery of new firmware to IP Phones. For further in...

[Page 94] Nortel IP Phone 1110

94 Nortel IP Phone 2002 Full Duplex mode In the Configuration menu, autonegotiate mode is the default setting for initial startup. Nortel recommends that autonegotiate mode is used on the network and the IP Phone. Use Full Duplex mode only when the ...

[Page 95] Nortel IP Phone 1110

Gratuitous Address Resolution Protocol Protection 95 When the IP Phone restarts, the firmware reads the setting for Full Duplex mode and sets the LAN Ethernet port, PC Ethernet port, duplex, and speed accordingly. Use Procedure 13 "Checking Eth...

[Page 96] Nortel IP Phone 1110

96 Nortel IP Phone 2002 Extensible Authentication Protocol Extensible Authentication Protocol (EAP) is a general protocol that fulfills the protocol requirements defined by 802.1x. For further information about 802.1x, see Appendix "802.1x Por...

[Page 97] Nortel IP Phone 1110

Removing an IP Phone 2002 from service 97 —End— Replacing an IP Phone 2002 ATTENTION Two IP Phones cannot share the same TN. You must remove the IP Phone 2002 that currently uses the TN. Procedure 15 Replacing an IP Phone 2002 Step Action 1 Obtai...

[Page 98] Nortel IP Phone 1110

98 Nortel IP Phone 2002 —End— Nortel Communication Server 1000 IP Phones Fundamentals NN43001-368 01.02 Standard Release 5.0 20 June 2007 Copyright © 2003–2007, Nortel Networks . ...

[Page 99] Nortel IP Phone 1110

99 Nortel IP Phone 2004 Contents This section contains the following topics: • "Introduction" (page 99) • "Description" (page 100) • "Components and functions" (page 101) • "Supported features" (page 10...

[Page 100] Nortel IP Phone 1110

100 Nortel IP Phone 2004 • Procedure 20 "Enabling Full Duplex mode" (page 130). • Procedure 21 "Checking Ethernet Statistics" (page 131). • Procedure 22 "Changing the TN of an existing IP Phone 2004" (page 132). �...