Stanton DJ Mixer DJLab.3 Owner's Manual

Download or browse on-line these Owner's Manual for Stanton DJ Mixer DJLab.3 DJ Equipment.

Stanton DJ Mixer DJLab.3 Manual Information:

This manual for Stanton DJ Mixer DJLab.3, given in the PDF format, is available for free online viewing and download without logging on. The guide contains 12 pages, and the size of the file at download is 6.83 Mb. The document type is Owner's Manual.

Download Manual

Summary of Contents:

[Page 1] Stanton DJ Mixer DJLab.3

S TAN T O N MAG N E T IC S , IN C +1 954- 689-8833 w w w . s t a n t o n d j . c o m [email protected] DJLab.3 OWNER'S MANUAL ...

[Page 2] Stanton DJ Mixer DJLab.3

IMPORTANT TO SAFETY 1. Read these Instructions 2. Keep these Instructions 3. Heed all Warnings 4. Follow all Instructions 5. Do not use this apparatus near water 6. Clean only with dry cloth 7. Do not block any ventilation openings...

[Page 3] Stanton DJ Mixer DJLab.3

LINE VOLTAGE SELECTION 115V 230V 1) The desired voltage of your turntable may be set with the VOLTAGE SELECTOR switch on the rear panel of the main unit, using a screwdriver. 2) Do not twist the VOLTAGE SELECTOR switch with excessive for...

[Page 4] Stanton DJ Mixer DJLab.3

M.202 CONTENTS 1) Input fader - Controls individual source levels/volume (channels) in the mix. 2) Input toggle switch - Selects which source will be active based on what you have connected to the rear panel input section (phono/line...

[Page 5] Stanton DJ Mixer DJLab.3

QUICK SETUP DIAGRAM Study this setup diagram. Make sure all faders are at "zero" and all devices are off. First, connect all input sources. Next, connect your microphone and monitor headphones. Finally, connect the stereo outputs to the...

[Page 6] Stanton DJ Mixer DJLab.3

SPECIFICATIONS M.202 INPUT / OUTPUT IMPEDANCE & SENSITIVITY: LINE -14dB/10K OHM ±2dB PHONO -50dB /47K OHM ±2dB MIC -60dB /2.2K OHM ±2dB MASTER 1K OHM PHONES 0dB/33 OHM ±2dB (LOAD=32 OHM) MAX. OUTPUT (THD=1%) MASTER M...

[Page 7] Stanton DJ Mixer DJLab.3

CONNECTIONS 1) Connect the power cord to an AC outlet. 2) Connect the RCA cable to the PHONO input of your mixer. You can also use a line input by setting the phono/line switch at the rear of the turntable to Line. Note: This turntable ha...

[Page 8] Stanton DJ Mixer DJLab.3

T.80 TURNTABLE CONTENTS 1) Start/Stop 2) Strobe Dots 3) Slipmat 4) Center Spindle 5) Motor ON/OFF Switch 6) Platter Revolution Speeds (RPM) 7) Target Light Base 8) Key Lock 9) Pitch Lock 10) Pitch Slider 11) Headshell Locking Nut 12...

[Page 9] Stanton DJ Mixer DJLab.3

SPECIFICATIONS T.80 POWER SOURCE AC 100V, 50/60Hz (For Japan) AC 110V, 60Hz (For Taiwan) AC 120V, 60Hz (For U.S.A.,Canada,Mexico) AC 220V, 50Hz (For United Arab Emirates,Chile,Argentina) AC 220V, 60Hz (For Phili...

[Page 10] Stanton DJ Mixer DJLab.3

Stanton Magnetics, Inc. – Warranty Provision – Returns for Repairs or Replacement WARRANTY Through Stanton’s authorized dealers around the World, Stanton, or one of Stanton’s authorized distributors outside the U.S., will, without charge...

[Page 11] Stanton DJ Mixer DJLab.3

STANTON WARRANTY REGISTRATION CARD PERSONAL INFO PRODUCT INFO Name Address City State Zip Country Telephone Model Number Serial Number Date of Purchase Where did you buy this product? If you have intern...

[Page 12] Stanton DJ Mixer DJLab.3

PLACE STAMP HERE Stanton Magnetics, Inc. 3000 SW 42nd Street Hollywood, FL 33312 U.S.A. ...