Triumph Speed Triple Handbook

[Page 1] Triumph Speed Triple

1 Foreword FOREWORD This handbook contains information on the Triumph Speed Triple and Speed Triple R motorcycles. Always store this owner's handbook with the motorcycle and refer to it for information whenever necessary. Warnings, Cautions and ...

[Page 2] Triumph Speed Triple

2 Foreword Warning Labels At certain areas of the motorcycle, the symbol (left) can be seen. The symbol means 'CAUTION: REFER TO THE HANDBOOK' and will be followed by a pictorial representation of the subject concerned. Never attempt to rid...

[Page 3] Triumph Speed Triple

3 Foreword Owner's Handbook Thank you for choosing a Triumph motorcycle. This motorcycle is the product of Triumph's use of proven engineering, exhaustive testing, and continuous striving for superior reliability, safety and performance. Pl...

[Page 4] Triumph Speed Triple

Foreword 4 Information The information contained in this publication is based on the latest information available at the time of printing. Triumph reserves the right to make changes at any time without prior notice, or obligation. Not to be reproduce...

[Page 5] Triumph Speed Triple

5 Foreword - Safety First FOREWORD - SAFETY FIRST The Motorcycle Fuel and Exhaust Fumes Warning This motorcycle is designed for on-road use only. It is not suitable for off-road use. Off-road operation could lead to loss of control of the motorcycl...

[Page 6] Triumph Speed Triple

6 Foreword - Safety First Riding Warning Never ride the motorcycle when fatigued or under the influence of alcohol or other drugs. Riding when under the influence of alcohol or other drugs is illegal. Riding when fatigued or under the influence of ...

[Page 7] Triumph Speed Triple

7 Foreword - Safety First Helmet and Clothing Handlebars and Footrests Warning When riding the motorcycle, both rider and passenger must always wear a motorcycle helmet, boots, eye protection, gloves, trousers (close fitting around the knee and ank...

[Page 8] Triumph Speed Triple

8 Foreword - Safety First Parking Parts and Accessories Triumph does not accept any liability whatsoever for defects caused by the fitting of non-approved parts, accessories or conversions or the fitting of any approved parts, accessories or conversi...

[Page 9] Triumph Speed Triple

9 Foreword - Safety First Maintenance/Equipment Warning Consult your authorised Triumph dealer whenever there is doubt as to the correct or safe operation of this Triumph motorcycle. Remember that continued operation of an incorrectly performing mo...

[Page 10] Triumph Speed Triple

Warning Labels 10 WARNING LABELS The labels detailed on this and the following pages draw your attention to important safety information in this handbook. Before riding, ensure that all riders have understood and complied with all the information to ...

[Page 11] Triumph Speed Triple

Warning Labels 11 Warning Label Locations (continued) Caution All warning labels and decals, with the exception of the Running-in label, are fitted to the motorcycle using a strong adhesive. In some cases, labels are installed prior to an applicati...

[Page 12] Triumph Speed Triple

12 Parts Identification PARTS IDENTIFICATION 1. Headlight 2. Radiator/Coolant pressure cap 3. Fuel filler cap 4. Fuel tank 5. Coolant expansion tank 6. Seat lock 7. S il en ce r 8. Rear light 9. Front brake disc 10.Front brake caliper 11. F r o n t ...

[Page 13] Triumph Speed Triple

13 Parts Identification PARTS IDENTIFICATION 16 . S i l e n c e r 17. Tool kit 18. Rear brake fluid reservoir 19.Battery 20.Front fork 21. Rear brake disc 22.Rear brake caliper 23.Rear suspension unit 24.Rear brake pedal 25.Oil filler cap/Dipstick 26...

[Page 14] Triumph Speed Triple

14 Parts Identification Parts Identification (continued) 1. C l u t c h l e v e r 2. Passing button 3. Headlight dip switch 4. Speedometer 5. Trip computer display 6. Tachometer 7. Warning lights 8. Front brake fluid reservoir 9. Engine stop switch ...

[Page 15] Triumph Speed Triple

15 Serial Numbers SERIAL NUMBERS Vehicle Identification Number (VIN) 1. VIN number The vehicle identification number is stamped into the right hand side of the steering head area of the frame. It is also displayed on a plate, riveted to the left han...

[Page 16] Triumph Speed Triple

Serial Numbers 16 This page intentionally left blank ...

[Page 17] Triumph Speed Triple

General Information 17 GENERAL INFORMATION Table of Contents Instrument Panel Layout. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Speedometer and Odometer. . . . . . . . . . . . . . ....

[Page 18] Triumph Speed Triple

18 General Information Tyre Pressures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Replacement Tyres. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

[Page 19] Triumph Speed Triple

19 General Information Tool Kit and Handbook . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 Seat Lock. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

[Page 20] Triumph Speed Triple

20 General Information Instrument Panel Layout 1. C l o c k 2. Service interval indicator 3. Speedometer 4. Fuel gauge 5. Engine management malfunction indicator light 6. Gear change lights 7. Left hand direction indicator light 8. ABS warning light...

[Page 21] Triumph Speed Triple

21 General Information Speedometer and Odometer The digital speedometer indicates the road speed of the motorcycle. The read-out displays the motorcycle road speed in increments of one kilometre (or mile) per hour. The electronic odometer and two tri...

[Page 22] Triumph Speed Triple

22 General Information • Set up is only accessible when the motorcycle is stationary and in neutral. Odometer/Trip Meter 1. B u t t o n A 2. Button B 3. Odometer/Trip meter display 4. Trip meter 1 display 5. Trip meter 2 display Trip Meter Either ...

[Page 23] Triumph Speed Triple

23 General Information Trip Meter Reset To reset either of the trip meters, select and display the trip meter to be zeroed then press button 'B' for 2 seconds. After 2 seconds, the trip meter on display will reset to zero. Note: • When a ...

[Page 24] Triumph Speed Triple

24 General Information Once both hours and minutes are correctly set, press button 'B' to confirm and t-SEt will be visible in the display screen. Press and release button 'A' until r Eturn is visible then press button 'B&apo...

[Page 25] Triumph Speed Triple

25 General Information To access the units display, with the motorcycle stationary and in neutral turn the ignition to the ON position. Press and release button 'A' until set up is visible in the display screen then press button 'B&apo...

[Page 26] Triumph Speed Triple

26 General Information ABS Disable (models with ABS only) It is possible to temporarily disable the ABS system. The ABS system cannot be permanently disabled, it will be enabled when the ignition is turned off and then on again. To Disable the ABS T...

[Page 27] Triumph Speed Triple

27 General Information Gear Change Lights The gear change lights provide a visual indication of when to change gear. The gear change lights are all coloured blue. 1. Display screen 2. Gear change lights 3. Button A 4. Button B Gear Change Light Modes...

[Page 28] Triumph Speed Triple

28 General Information Note: • The motorcycle is delivered from the factory with the gear change light set to the 6 LED mode at 3,500 rpm. 1. Gear change lights 2. Display screen (3 mode shown) 3. Button A 4. Button B When the gear change light mod...

[Page 29] Triumph Speed Triple

29 General Information When the correct setting is shown press button 'B' and the rpm 100 units start flashing. 1. R P M 10 0 u n i t s 2. Button A 3. Button B The setting can now be changed in increments of 100 rpm, again up to the maxim...

[Page 30] Triumph Speed Triple

30 General Information Lap Timer 1. Display screen 2. Button A The lap timer will provide the following information: lap time, number of laps, average speed, maximum speed and distance travelled. Each display provides the following information: Lap t...

[Page 31] Triumph Speed Triple

31 General Information Data Recording Mode 1. L a p d i s p l a y 2. Stop watch icon 3. Lap time Note: • The data recording mode and the data retrieval mode will only operate when the lap timer (lap) is turned on. To select the data recording mode...

[Page 32] Triumph Speed Triple

32 General Information Data Retrieval Mode 1. Lap number 2. Stop watch icon 3. Lap timer 4. Button A 5. Button B The data retrieval mode can be accessed in one of two ways: • With the ignition in the ON position, from the lap timer display, press b...

[Page 33] Triumph Speed Triple

33 General Information • Distance Travelled (per lap or total of all laps) •Lap Time 1. Lap number 2. Stop watch icon 3. Data Retrieval Mode (average speed shown) 4. Button A 5. Button B The speed and distance will be displayed in kilometres or ...

[Page 34] Triumph Speed Triple

34 General Information Fuel Gauge 1. F u e l g a u g e 2. Button B The fuel gauge indicates the amount of fuel in the tank. With the ignition switched on, the number of bars shown in the display indicates the level of fuel. When the fuel tank is ful...

[Page 35] Triumph Speed Triple

35 General Information Tyre Pressure Sensor Serial Number The serial number for each tyre pressure sensor is printed on a label which is on the sensor. This number may be required by the dealer for service or diagnostics. If the TPMS has been fitted ...

[Page 36] Triumph Speed Triple

36 General Information To exit the tyre pressure display, press and release button 'A' to the desired display. Sensor Batteries When the battery voltage in a pressure sensor is low, LO bAt will be displayed and the TPMS symbol will indicate...

[Page 37] Triumph Speed Triple

37 General Information Warning Lights Direction Indicators When the indicator switch is pushed to the left or right, the direction indicator light will flash on and off at the same speed as the turn indicators. High Beam When the ignition is switched...

[Page 38] Triumph Speed Triple

38 General Information Engine Management System Malfunction Indicator Light The malfunction indicator light for the engine management system illuminates when the ignition is switched on (to indicate that it is working) but should not become illumina...

[Page 39] Triumph Speed Triple

39 General Information ABS (Anti-Lock Brake System) Indicator light (Only on models fitted with ABS) When the ignition switch is turned to the ON position, it is normal that the ABS warning light will flash on and off. The light will continue to fla...

[Page 40] Triumph Speed Triple

40 General Information The tyre pressure at which the warning light illuminates is temperature compensated to 20°C but the numeric pressure display associated with it is not (see page 36). Even if the numeric display seems at or close to the standar...

[Page 41] Triumph Speed Triple

41 General Information Always get replacement keys from your authorised Triumph dealer. Replacement keys must be 'paired' with the motorcycle’s immobiliser by your authorised Triumph dealer. Ignition Switch/Steering Lock 1. Ignition switc...

[Page 42] Triumph Speed Triple

42 General Information TO LOCK: Turn the steering fully to the left, turn the key to the OFF position, push and fully release the key, then rotate it to the LOCK position. PARKING: Turn the key from the LOCK position to the P position. The steering w...

[Page 43] Triumph Speed Triple

43 General Information Brake Lever 1. Brake lever 2. Adjusting screw To adjust the brake lever, push the lever forward and turn the adjusting screw in to increase the distance or out to shorten the distance from the handlebar. Right Handlebar Switche...

[Page 44] Triumph Speed Triple

44 General Information Starter Button The starter button operates the electric starter. For the starter to operate, the clutch lever must be pulled to the handlebar. Note: • Even if the clutch lever is pulled to the handlebar, the starter will not ...

[Page 45] Triumph Speed Triple

45 General Information Direction Indicator Switch When the indicator switch is pushed to the left or right and released, the corresponding direction indicators will flash on and off. To turn off the indicators, push and release the switch. Horn Butto...

[Page 46] Triumph Speed Triple

46 General Information Fuel Tank Cap 1. F u e l t a n k c a p 2. Key To open the fuel tank cap, lift up the flap covering the lock itself. Insert the key into the lock and turn the key clockwise. To close and lock the cap, push the cap down into p...

[Page 47] Triumph Speed Triple

47 General Information Filling the Fuel Tank Avoid filling the tank in rainy or dusty conditions where airborne material can contaminate the fuel. Fill the fuel tank slowly to help prevent spillage. Do not fill the tank to a level above the bottom of...

[Page 48] Triumph Speed Triple

48 General Information Stand Side Stand 1. S i d e s t a n d The motorcycle is equipped with a side stand on which the motorcycle can be parked. Note: • When using the side stand, always turn the handlebars fully to the left and leave the motorcyc...

[Page 49] Triumph Speed Triple

49 General Information Seat Lock 1. S e a t l o c k The seat lock is located on the left hand side of the motorcycle, on the frame below the seat. To remove the seat, insert the ignition key into the seat lock and turn it anti-clockwise while pressi...

[Page 50] Triumph Speed Triple

50 General Information Tie-Down Hooks Located on the underside of the seat are the tie-down hooks. The tie-down hooks are designed to help secure a load up to 3.5 kg (7.5 lb) to the seat using a rope. To access and use the tie-down hooks, remove the ...

[Page 51] Triumph Speed Triple

51 General Information Running-In Running-in is the name given to the process that occurs during the first hours of a new vehicle's operation. In particular, internal friction in the engine will be higher when components are new. Later on, when...

[Page 52] Triumph Speed Triple

52 General Information Safe Operation Daily Safety Checks Check the following items each day before you ride. The time required is minimal, and these checks will help ensure a safe, reliable ride. If any irregularities are found during these checks, ...

[Page 53] Triumph Speed Triple

53 General Information Brake Pads: There should be more than 1.0 mm of friction material remaining on the front brake pads and more than 1.5 mm for the rear (see page 93). Brake Fluid Levels: No brake fluid leakage. Brake fluid levels must be betwee...

[Page 54] Triumph Speed Triple

General Information 54 This page intentionally left blank ...

[Page 55] Triumph Speed Triple

How to Ride the Motorcycle 55 HOW TO RIDE THE MOTORCYCLE Table of Contents To Stop the Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 To Start the Engine . . . . . . . ....

[Page 56] Triumph Speed Triple

56 How to Ride the Motorcycle To Stop the Engine 1. Engine stop switch 2. Starter button 3. Neutral indicator light 4. ON position 5. Ignition switch Close the throttle completely. Select neutral. Turn the ignition switch off. Select first gear. Supp...

[Page 57] Triumph Speed Triple

57 How to Ride the Motorcycle Leaving the throttle fully closed, push the starter button until the engine starts. Slowly release the clutch lever. • The motorcycle is equipped with starter lockout switches. The switches prevent the electric starter...

[Page 58] Triumph Speed Triple

58 How to Ride the Motorcycle Changing Gears 1. Gear change pedal Close the throttle while pulling in the clutch lever. Change into the next higher or lower gear. Open the throttle part way, while releasing the clutch lever. Always use the clutch whe...

[Page 59] Triumph Speed Triple

59 How to Ride the Motorcycle Braking 1. Front brake lever 1. Rear brake pedal Warning WHEN BRAKING, OBSERVE THE FOLLOWING: Close the throttle completely, leaving the clutch engaged to allow the engine to help slow down the motorcycle. Change down...

[Page 60] Triumph Speed Triple

60 How to Ride the Motorcycle Warning For your safety, always exercise extreme caution when braking, (whether or not ABS is fitted), accelerating or turning as any incautious action can cause loss of control and an accident. Independent use of the ...

[Page 61] Triumph Speed Triple

61 How to Ride the Motorcycle ABS (Anti-Lock Brake System) models only ABS Warning Light When the ignition switch is turned to the ON position, it is normal for the ABS warning light to flash on and off (see page 39). If the ABS warning light is con...

[Page 62] Triumph Speed Triple

62 How to Ride the Motorcycle Parking Select neutral and turn the ignition switch to the OFF position. Lock the steering to help prevent theft. Always park on a firm, level surface to prevent the motorcycle from falling. When parking on a hill, alway...

[Page 63] Triumph Speed Triple

63 How to Ride the Motorcycle Do not leave the switch in the P position for long periods of time as this will discharge the battery. Considerations for High-Speed Operation Warning Do not park on a soft or on a steeply inclined surface. Parking un...

[Page 64] Triumph Speed Triple

64 How to Ride the Motorcycle General Ensure the motorcycle has been maintained according to the scheduled maintenance chart. Steering Check that the handlebar turns smoothly without excessive free play or tight spots. Ensure that the control cables ...

[Page 65] Triumph Speed Triple

65 How to Ride the Motorcycle Engine Oil Make certain that the engine oil level is correct. Ensure that the correct grade and type of oil is used when topping up. Coolant Check that the coolant level is at the upper level line in the expansion tank....

[Page 66] Triumph Speed Triple

How to Ride the Motorcycle 66 This page intentionally left blank ...

[Page 67] Triumph Speed Triple

67 Accessories and Loading ACCESSORIES AND LOADING The addition of accessories and carriage of additional weight can affect the motorcycle's handling characteristics causing changes in stability and necessitating a reduction in speed. The follow...

[Page 68] Triumph Speed Triple

68 Accessories and Loading Warning This motorcycle must not be operated above the legal road speed limit except in authorised closed-course conditions. Warning Only operate this Triumph motorcycle at high speed in closed-course on-road competitio...

[Page 69] Triumph Speed Triple

69 Accessories and Loading Warning The handling and braking capabilities of a motorcycle will be affected by the presence of a passenger. The rider must make allowances for these changes when operating the motorcycle with a passenger and should not...

[Page 70] Triumph Speed Triple

70 Accessories and Loading This page intentionally left blank ...

[Page 71] Triumph Speed Triple

Maintenance and Adjustment 71 MAINTENANCE AND ADJUSTMENT Table of Contents Scheduled Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74 Engine Oil. . . . . . . . . . . . . . . ....

[Page 72] Triumph Speed Triple

Maintenance and Adjustment 72 Brake Light Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96 Steering/Wheel Bearings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

[Page 73] Triumph Speed Triple

Maintenance and Adjustment 73 Direction Indicator Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .119 Bulb Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....

[Page 74] Triumph Speed Triple

74 Maintenance and Adjustment Scheduled Maintenance To maintain the motorcycle in a safe and reliable condition, the maintenance and adjustments outlined in this section must be carried out as specified in the schedule of daily checks, and also in li...

[Page 75] Triumph Speed Triple

Maintenance and Adjustment 75 Operation Description Odometer Reading in Miles (Kms) or Time Period, whichever comes first First Service A Service B Service C Service D Service Every 500 (800) 1 month 6,000 (10,000) 1 year 12,000 (20,000) 2 years 18 ...

[Page 76] Triumph Speed Triple

Maintenance and Adjustment 76 * Evaporative system fitted to models for certain markets only. Brake fluid - renew - •• Brake pad wear - check Day ••••• Brake master cylinders – check for oil leaks - ••••• Brake calipers - ch...

[Page 77] Triumph Speed Triple

77 Maintenance and Adjustment Engine Oil In order for the engine, transmission, and clutch to function correctly, maintain the engine oil at the correct level, and change the oil and oil filter in accordance with scheduled maintenance requirements. ...

[Page 78] Triumph Speed Triple

78 Maintenance and Adjustment Oil Level Inspection 1. Filler 2. Filler plug/dipstick 3. Upper marking 4. Lower marking Note: • An accurate indication of the level of oil in the engine is only shown when the engine oil is at normal operating tempera...

[Page 79] Triumph Speed Triple

79 Maintenance and Adjustment Oil and Oil Filter Change 1. Oil drain plug 2. Oil filter The engine oil and filter must be replaced in accordance with scheduled maintenance requirements. Warm up the engine thoroughly, and then stop the engine and secu...

[Page 80] Triumph Speed Triple

80 Maintenance and Adjustment Ensure that the low oil pressure warning light extinguishes shortly after starting. Turn off the ignition, check the oil level using the method previously described, and top up to between the minimum and maximum level li...

[Page 81] Triumph Speed Triple

81 Maintenance and Adjustment Cooling System To ensure efficient engine cooling, check the coolant level each day before riding the motorcycle, and top up the coolant if the level is low. Note: • A year-round, Hybrid Organic Acid Technology (known ...

[Page 82] Triumph Speed Triple

82 Maintenance and Adjustment Coolant Level Inspection 1. Expansion tank cover 2. MAX mark 3. MIN mark 4. Expansion tank Position the motorcycle on level ground and in an upright position. The coolant level within the expansion tank can be inspected ...

[Page 83] Triumph Speed Triple

83 Maintenance and Adjustment Note: • If the coolant level is being checked because the coolant has overheated, also check the level in the radiator and top up if necessary. • In an emergency, distilled water can be added to the cooling system. ...

[Page 84] Triumph Speed Triple

84 Maintenance and Adjustment Fuel Tank Raising Remove the seat (see page 49) and remove the fuel tank prop from its location on the seat base. Store the seat as described on page 49. 1. S e a t 2. Fuel tank prop Release the three fixings and remove ...

[Page 85] Triumph Speed Triple

85 Maintenance and Adjustment Pivot the fuel tank upwards at the front. While holding the fuel tank in the raised position, locate the fuel tank prop into the support points on the air box and the fuel tank. 1. Fuel tank prop 2. Fuel tank 3. Supporti...

[Page 86] Triumph Speed Triple

86 Maintenance and Adjustment Inspection Check that the throttle opens smoothly, without undue force and that it closes without sticking. Have your authorised Triumph dealer check the throttle system if a problem is detected or any doubt exists. Chec...

[Page 87] Triumph Speed Triple

87 Maintenance and Adjustment If there is an incorrect amount of free play, Triumph recommends that you have adjustments made by your authorised Triumph dealer. However, in an emergency, throttle adjustment may be made as follows: 1. Opening cable ad...

[Page 88] Triumph Speed Triple

88 Maintenance and Adjustment Refit the fuel tank. Reconnect the battery, positive (red) lead first. Refit the front panel to the fuel tank and tighten the fixings to 2Nm. Refit the seat (see page 49). Check that the throttle opens smoothly, without ...

[Page 89] Triumph Speed Triple

89 Maintenance and Adjustment Inspection Check that there is 2 - 3 mm clutch lever free play at the lever. If there is an incorrect amount of free play, adjustments must be made. Adjustment Turn the adjuster on the clutch lever until the correct amou...

[Page 90] Triumph Speed Triple

90 Maintenance and Adjustment Chain Lubrication Lubrication is necessary every 200 miles and also after riding in wet weather, on wet roads, or any time that the chain appears dry. Use the special chain lubricant as recommended in the Specification s...

[Page 91] Triumph Speed Triple

91 Maintenance and Adjustment Chain Free-Movement Adjustment 1. Adjuster clamp bolt 2. C-spanner 3. Eccentric adjuster Loosen the adjuster clamp bolt. Using the C-spanner supplied in the tool kit, turn the rear hub/eccentric adjuster (clockwise to lo...

[Page 92] Triumph Speed Triple

92 Maintenance and Adjustment Chain and Sprocket Wear Inspection 1. Measure across 20 links 2. Weight Stretch the chain taut by hanging a 10 - 20 kg weight on the chain. Measure the length of 20 links on the straight part of the chain from pin centre...

[Page 93] Triumph Speed Triple

93 Maintenance and Adjustment Brakes Brake Wear Inspection 1. Brake caliper, Speed Triple shown 2. Brake pads Brake pads must be inspected in accordance with scheduled maintenance requirements and replaced if worn to, or beyond the minimum service th...

[Page 94] Triumph Speed Triple

94 Maintenance and Adjustment Brake Pad Wear Compensation Disc and brake pad wear is automatically compensated for and has no effect on the brake lever or pedal action. There are no parts that require adjustment on the front and rear brakes. Disc Bra...

[Page 95] Triumph Speed Triple

95 Maintenance and Adjustment Brake Fluid Level Inspection and Adjustment 1. Front brake fluid reservoir, MAX level line 2. MIN level line The brake fluid level in the reservoirs must be kept between the MAX and MIN level lines (reservoir held hori...

[Page 96] Triumph Speed Triple

96 Maintenance and Adjustment Brake Light Switches The brake light is activated independently by either the front or rear brake. If, with the ignition in the ON position, the brake light does not work when the front brake lever is pulled or the rear ...

[Page 97] Triumph Speed Triple

97 Maintenance and Adjustment Inspecting the Steering (Headstock) Bearings for Free Play Position the motorcycle on level ground, in an upright position. Raise the front wheel above the ground and support the motorcycle. Standing at the front of the...

[Page 98] Triumph Speed Triple

98 Maintenance and Adjustment Front Suspension Front Fork Inspection Examine each fork for any sign of damage, scratching of the slider surface, or for oil leaks. If any damage or leakage is found, consult an authorised Triumph dealer. To check that ...

[Page 99] Triumph Speed Triple

99 Maintenance and Adjustment Suspension Setting Chart - Speed Triple Suspension Setting Chart - Speed Triple R Note: • These charts are only a guide. Setting requirements may vary for rider weight and personal preferences. See the following pages ...

[Page 100] Triumph Speed Triple

100 Maintenance and Adjustment Front Suspension Settings Spring Pre-Load Adjustment 1. Speed Triple spring pre-load adjuster 1. Speed Triple R spring pre-load adjuster Warning Ensure that the correct balance between front and rear suspension is ma...