Bosch AMC2 Installation Manual

Download or browse on-line these Installation Manual for Bosch AMC2 Controller, Control Unit.

Bosch AMC2 Manual Information:

This manual for Bosch AMC2, given in the PDF format, is available for free online viewing and download without logging on. The guide contains 54 pages, and the size of the file at download is . The document type is Installation Manual.

Download Manual

More Manuals:

In case you failed to obtain relevant information in this document, please, look through related operating manuals and user instructions for Bosch AMC2. Just click one of the links below to go to the selected manual:

Summary of Contents:

[Page 1] Bosch AMC2

AMC2 Wiegand Extension AMC2-4WE en Installation manual ...

[Page 2] Bosch AMC2

...

[Page 3] Bosch AMC2

Table of contents 1 Safety Instructions 5 1.1 Important Safety Notes 5 1.2 Safety Precautions 7 1.3 Unpacking 9 2 Important Information 10 2.1 Explanation of symbols in this document 10 2.2 Internet 11 3 Introduction 12 3.1 Description 12 3.2 Equipme...

[Page 4] Bosch AMC2

6 Technical Data 44 7 Appendices 48 7.1 Connecting Diagrams 48 Index 51 4 en | Table of Contents AMC2 Wiegand Extension 2016-11 | AMC2-4WE | Bosch Sicherheitssysteme GmbH ...

[Page 5] Bosch AMC2

Safety Instructions Important Safety Notes 1. Read, follow, and retain instructions - All safety and operating instructions must be read and followed properly before putting the unit into operation. Retain instructions for future reference. 2. Do n...

[Page 6] Bosch AMC2

adjustment of other controls may result in damage, and require extensive work by a qualified technician to restore the unit to normal operation. – If the unit has been dropped or the cabinet damaged. – If the unit exhibits a distinct change in pe...

[Page 7] Bosch AMC2

Safety Precautions Read instructions! Before working with the AMC2 device, read these instructions carefully. Make sure you have understood all information described in this document. ! Warning! Risk of electric shock External power supplies must b...

[Page 8] Bosch AMC2

! Warning! Risk of explosion of Lithium battery The battery can explode if it is replaced incorrectly. Replace only with the same type as recommended by the manufacturer. Dispose used batteries according to the battery manufacturer’s instructions....

[Page 9] Bosch AMC2

This symbol means that electrical and electronic equipment, at their end-of-life, should be disposed of separately from your household waste. In the European Union, there are separate collection systems for used electrical and electronic products. Pl...

[Page 10] Bosch AMC2

Important Information Remarks This hardware is part of a security system. Access should be limited to authorized persons only. Some states do not allow the exclusion or limitation of implied warranties, or limitation of liability for incidental or co...

[Page 11] Bosch AMC2

! Caution! Cause of Hazard Indicates a hazardous situation, which, if not avoided, could result in minor or moderate injury. Notice! Cause of Hazard Important Notes that must be followed to avoid damage to the equipment or environment, and to ensure...

[Page 12] Bosch AMC2

Introduction Description The extension module AMC2-4WE is equipped with four Wiegand type reader-interfaces plus eight inputs and eight outputs. Hence with the AMC2-4WE it is possible to double the number of readers on an AMC2-4W from 4 to 8. Figure ...

[Page 13] Bosch AMC2

Notice! The AMC2-4WE has no display. The information about the input and outputs will be shown on special pages of the AMC2 display. As the extension modules contain neither memory nor display they are controlled and monitored entirely by the AMC2-4W...

[Page 14] Bosch AMC2

Equipment Configuration Figure 3.2: Overview - Interfaces 1 RS-485 extension module bus 2 External tamper contact 3 Connector for power supply 4 Wiegand interfaces for up to 4 card readers 5 Connectors for eight analog inputs 6 Connectors for eight...

[Page 15] Bosch AMC2

Figure 3.3: Jumpers at the bottom side 7 Jumper for setting either voltage free relay output (“dry” mode) or looped-in voltage from the AMC2 internal power supply (“wet” mode). 8 Jumper: Equalization of potential between different systems and...

[Page 16] Bosch AMC2

Performance Characteristics – Controlled by an AMC2 via RS-485 – Reader interfaces – four Wiegand interfaces – Eight relay outputs – voltage free, power is supplied externally (dry mode) – powered by internal power supply (wet mode) – E...

[Page 17] Bosch AMC2

Figure 3.4: System overview 1 = Host 2 = AMC2-4W 3 = Card reader 4 = Communication and power supply 5 = AMC2-4WE System configurations for Access Control applications. – The minimum configuration consists of: – one PC with system software, – ...

[Page 18] Bosch AMC2

– Each AMC2-4W controller can be extended with an AMC2-4WE extension module. The using of AMC2-4WE modules has no influence on the limit of the maximum of controllers in one system, because it is an extension to an AMC2-4W and not a controller. Usi...

[Page 19] Bosch AMC2

Installing Notice! To build an UL approved system refer the documentation contained in the folder titled "_UL" on the delivered CD. Mounting The AMC2-4WE can be attached on a standard 35 mm (1.377 in.) mounting rail using a snap-in mechanis...

[Page 20] Bosch AMC2

Unmounting Notice! To remove the AMC2-4WE from a mounting rail, first remove all pluggable connectors. Push down the AMC2-4WE until the lower edge snaps out of the mounting rail [1]. Pull the lower end of the AMC2-4WE from the mounting rail [2]. Fi...

[Page 21] Bosch AMC2

Opening the Case Notice! To open the AMC2-4WE, first remove all pluggable connectors. The AMC2-4WE case consists of a top cover mounted with a two-point snap-in closure on a chassis. To open the case, push down the two snap-ins with a screwdriver, ...

[Page 22] Bosch AMC2

Closing the Case Before aligning the covers, unplug any pluggable screw connectors. Insert the hooks on the lower edge of the front cover into the lugs on lower edge of the plastic back cover [1]. Please ensure that the BOSCH logo is not upside-down....

[Page 23] Bosch AMC2

Notice! Risk of damage to equipment If excessive force is required to close the front cover then it is probably incorrectly hooked into the back cover. In such cases the display ’Dialog’ button in the front cover will be misaligned and will not f...

[Page 24] Bosch AMC2

i.e. RAWG18 (acc. specs) = 6.385 or 20,948 U Drop = 20,948 x 0.1 km x 1A = 2.1V U Drop = 6.385 x 328 ft x 1A = 2.1V Critical condition! Install the power supply closer to the controller. Notice! These specifications apply to power supply, re...

[Page 25] Bosch AMC2

Grounding and Shielding The AMC2 controller allows you to create a central ground or shielding point, simply by setting certain jumpers. Set these jumpers only if grounding or shielding is not achieved by other means. 1. If the AMC2-4WE has its own p...

[Page 26] Bosch AMC2

Notice! In general the following apply: If the devices have their own power supplies, the shielding is applied to one side only. The free end should be insulated to avoid inadvertent connections. If one device is fed power by another, the cable shiel...

[Page 27] Bosch AMC2

Connecting Power Supply Direct Power Supply Connect the power supply to the POWER 7-pin pluggable screw connector. Refer to Connecting Diagrams, page 48 for a complete diagram. Figure 4.6: Location of the power supply connector Connect an externa...

[Page 28] Bosch AMC2

Power Supply via RS-485 Interface The power can also be supplied by the AMC2-4W. In this case power pins 1 and 2 should be connected, as well as data lines on pins 3 - 6. Figure 4.7: Interface for internal power supply 4.7.2 28 en | Installing AMC2 W...

[Page 29] Bosch AMC2

Overview - Power supply/consumption Figure 4.8: Example configurations a = AMC2-4WE b = AMC2 I/O Extension board line = Power supply broken line = Data line 4.7.3 AMC2 Wiegand Extension Installing | en 29 Bosch Sicherheitssysteme GmbH 2016-11 | AMC2-...

[Page 30] Bosch AMC2

Example Components used Output power Consumptio n Available Constant load 1 PS + AMC2-4W 60VA 5VA 55VA 25VA 2 PS + AMC2-4W + AMC2-4WE 60VA 2 x 5VA 50VA 20VA PS + AMC2-4W + AMC2-4WE + Extension 60VA 3 x 5VA 45VA 15VA 3 PS + AMC2-4W and PS + AMC2-4WE 6...

[Page 31] Bosch AMC2

Constant load Amount of the available power that can be drawn constantly. Hence Example 1 can be read as follows: Of the total incoming power (60VA) 5VA will be drawn by the AMC2 itself . This leaves 55VA to support external devices. 25VA of these 55...

[Page 32] Bosch AMC2

RS-485 for extension modules The AMC2-4WE is connected to the AMC2 controller using the RS-485 extension interface. This interface will also be used to connect further extension modules. Figure 4.9: Location of the RS-485 extension module bus Figur...

[Page 33] Bosch AMC2

Wiegand Interface for Card Readers Notice! If your reader requires a voltage other than 12V or is the power consumption more than 200 mA then it will require an external power supply. The AMC2-4WE provides four ports for connecting a maximum of 4 rea...

[Page 34] Bosch AMC2

Refer to Connecting Diagrams, page 48 for a complete wiring diagram of the Wiegand reader interface . Connecting Relay Outputs To operate locks or alarm systems, the AMC2-4WE has eight form C relay outputs. The outputs will be connected to the 3...

[Page 35] Bosch AMC2

Figure 4.13: Wet mode and dry mode of the AMC2 relay outputs Notice! Risk of damage to equipment To prevent damage to the relays note the following specifications. – the maximum switching current is 1.25 A – the maximum switching voltage is 30 ...

[Page 36] Bosch AMC2

A complete connection diagram of the relay output connectors is shown in Connecting Diagrams, page 48. Figure 4.14: Recovery diode schematic 1 normally open/ normally closed 1 normally open/ normally closed 2 common 2 common 3 load 3 load 4 diode 4...

[Page 37] Bosch AMC2

Each relay output has a separate jumper setting on the underside of the circuit board to select dry (D 1) or wet (D 2) mode. Figure 4.15: Location of relay output jumpers (bottom side) Notice! The positions of the jumpers 1 and 2 are interchanged rel...

[Page 38] Bosch AMC2

Connecting Analog Input Devices The AMC2-4WE has 8 analog inputs, for example, for potential- free lock mechanisms, or to detect whether a lock is closed or open. The inputs will be connected to the 2-pin pluggable screw connectors: S3, S4, S8, S9, S...

[Page 39] Bosch AMC2

1. Door open: R S + R P 2. Door closed: R S 3. Open wire: R S + R P = ∞ 4. Short circuit: R S + R P = 0 The resistor values can vary and depend on the used lock system. The extension package includes 2,2 kΩ resistors which can be used to ...

[Page 40] Bosch AMC2

R P 1k 1k2 1k5 1k8 2k2 2k7 3k3 3k9 4k7 5k6 6k8 8k2 R S 1k 220 220 220 210 200 1k2 260 270 270 270 260 240 1k5 310 330 340 350 350 340 310 280 1k8 340 380 390 410 410 410 400 370 330 290 200 ...

[Page 41] Bosch AMC2

Tamper Protection To protect the AMC2-4WE against unauthorized access and so prevent tampering with sensitive data, the AMC2-4WE provides an additional interface to connect external tamper contacts. This interface is a potential-free 2-pin pluggable ...

[Page 42] Bosch AMC2

Operating Status Display of the AMC2 Because the AMC2-4WE has no display of its own, the AMC2 controller displays status information about the input and output settings of the AMC2-4WE. The selected display mode remains set until the next time the ...

[Page 43] Bosch AMC2

Push Display (Example) Description 3c Dig. I3: :::::::::::::::: 4 MAC 0010174C8A0C Network device address (MAC) 5 N AMC-1234-5678 Network name of the AMC2 6 I 192.168.10.18 IP-address of the AMC2 7 G 192.168.10.255 IP-address of the gateway (Version ...

[Page 44] Bosch AMC2

Technical Data – Four Wiegand interfaces for up to four card readers (Output rating: 280 mA) – Eight relay outputs – maximum ratings (wet and dry): switching voltage: 30 Vdc switching current: 1,25 A – operating ratings (wet and dry): 1,25 A ...

[Page 45] Bosch AMC2

Environment temperature 0° C to 50°C (32° F to 122°F) Humidity Up to 95%, without condensation Housing material ABS with OC (UL 94 V-0) Dimensions (W/H/D) 232 x 90 x 46mm (8.9 x 3.5 x 1.8 in) Weight approx. 0.4kg (0.9lb) Notice! The vol...

[Page 46] Bosch AMC2

46 en | Technical Data AMC2 Wiegand Extension 2016-11 | AMC2-4WE | Bosch Sicherheitssysteme GmbH ...

[Page 47] Bosch AMC2

AMC2 Wiegand Extension Technical Data | en 47 Bosch Sicherheitssysteme GmbH 2016-11 | AMC2-4WE | ...

[Page 48] Bosch AMC2

Appendices Connecting Diagrams Figure 7.1: Connector blocks of the AMC2-4WE 7 7.1 48 en | Appendices AMC2 Wiegand Extension 2016-11 | AMC2-4WE | Bosch Sicherheitssysteme GmbH ...

[Page 49] Bosch AMC2

1 Power supply, DC positive (10V - 30V) 2 Shield 3 Power supply (0V) 4 UPS (power good signal) - AC 5 UPS (power good signal) - Battery 6 UPS (power good signal) - DC 7 UPS (power good signal) - Common Table 7.1: Power supply 1 red Reader Supply (12V...

[Page 50] Bosch AMC2

1 Analog Input, in 2 Analog Input, out Table 7.3: Analog input 1 Relay Output, normally open 2 Relay Output, common 3 Relay Output, normally closed Table 7.4: Relay output 1 Power supply for external devices (10V - 30V) 2 Power supply for external de...

[Page 51] Bosch AMC2

Index C cabling, 23 E extension interface, 44 I inputs, 14, 16, 38 interfaces extension, 44 reader, 16, 33, 44 M mounting, 19 O opening, 21 outputs, 14, 16, 34, 44 P power supply, 23, 27 R reader interfaces, 16, 33, 44 Wiegand, 33 resistor, 38 T tamp...

[Page 52] Bosch AMC2

...

[Page 53] Bosch AMC2

...

[Page 54] Bosch AMC2

Bosch Sicherheitssysteme GmbH Robert-Bosch-Ring 5 85630 Grasbrunn Germany www.boschsecurity.com © Bosch Sicherheitssysteme GmbH, 2016 ...