ACME TB-1010QW II User Manual

[Page 1] ACME TB-1010QW II

TB-1010QW II User Manual Please read the instruction carefully before use ...

[Page 2] ACME TB-1010QW II

CONTENTS 1. Safety Instructions .................................................................................................. 2 2. Technical Specifications ........................................................................................

[Page 3] ACME TB-1010QW II

1. Safety Instructions WARNING Please keep this User Guide for future consultation. If you sell the unit to another user, be sure that they also receive this instruction booklet.  Unpack and check carefully there is no transportati...

[Page 4] ACME TB-1010QW II

Warning:  To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or moisture.  The housing and lenses must be replaced if they are visibly damaged. Installation: The fixture should be mounted via its screw...

[Page 5] ACME TB-1010QW II

Distance(m) 2 4 6 8 9227 4374 1025 57710 Lux ° Diameter(m) 1 0° Photometrics Diagram 0 32. 0 63. 0.96 1 28. 3. How To Set The Un...

[Page 6] ACME TB-1010QW II

UP To go forward in the selected functions ENTER To confirm the selected functions 5. POWER OUT: Water proof connectors for power output; 6. DMX OUT: Water proof connectors for DMX 512 operation, 3-pin XLR cable to output DMX signal;...

[Page 7] ACME TB-1010QW II

MENU DMX ADDRESS CHANNEL MODE SHOW MODE BLACKOUT MODE MANUAL TEST WHITE BALANCE PASSWORD LOCK DISPLAY INVERSION NORMAL AUTO TEST LED DISPLAY FIXTURE TEMPERATURE FIXTURE USE HOURS FIRMWARE VERSION DIMMER SPEED 6A ...

[Page 8] ACME TB-1010QW II

DMX 512 ADDRESS To select , press the ENTER button to show DMX ADDRESS on the display. Use the DOWN/UP buttons to adjust the address from 1 to 512. Once the address has been selected, press the ENTER button to setup. To go back to the f...

[Page 9] ACME TB-1010QW II

MANUAL TEST To select , press the ENTER button to show MANUAL TEST on the display. Use the DOWN/UP button to select (red), (green), (blue), (white), (dimmer) or (strobe) on the display. Once the mode has been selecte...

[Page 10] ACME TB-1010QW II

DISPLAY INVERSE To select , press the ENTER button to show DISPLAY INVERSE on the display, and press the ENTER button again, it will show the (inversion). To go back to the functions without any changes press the MENU button. AUTO TEST ...

[Page 11] ACME TB-1010QW II

seconds to exit the current mode. SOFTWARE VERSION To select , press the ENTER button to show SOFTWARE VERSION on the display and the display will show the version of software of the unit . To go back to the functions without any changes pres...

[Page 12] ACME TB-1010QW II

3. At last fixture, the DMX cable has to be terminated with a terminator to reduce signal errors. Solder a 120Ω, 1/4W resistor between pin 2(DMX-) and pin 3(DMX+) into a 3-pin XLR-plug and plug it in the DMX-output of the last fixture. 4. Each ...

[Page 13] ACME TB-1010QW II

4.3 DMX 512 Configurations 4 Channels Mode: CHANNEL VALUE FUNCTION 1 000-255 RED 0% ~ 100% 2 000-255 GREEN 0% ~ 100% 3 000-255 BLUE 0% ~ 100% 4 000-255 WHITE 0% ~ 100% 5 Channels Mode: CHANNEL VALUE F...

[Page 14] ACME TB-1010QW II

7 Channels Mode: CHANNEL VALUE FUNCTION 1 000-255 RED 0% ~ 100% 2 000-255 GREEN 0% ~ 100% 3 000-255 BLUE 0% ~ 100% 4 000-255 WHITE 0% ~ 100% 5 000-007 008-015 016-023 024-030 031-038 039-046 047-054 055...

[Page 15] ACME TB-1010QW II

241-247 248-255 Color 31 Color 32 6 000-255 DIMMER 0% ~ 100% 7 000-007 008-015 016-131 132-139 140-181 182-189 190-231 232-239 240-247 248-255 STROBE OFF Open Strobe, slow  fast Open Slow open, fast close Open ...

[Page 16] ACME TB-1010QW II

39 000-255 BLUE10 0% ~ 100% 40 000-255 WHITE10 0% ~ 100% 5. Troubleshooting Following are a few common problems that may occur during operation. Here are some suggestions for easy troubleshooting: Problem Possible ...

[Page 17] ACME TB-1010QW II

6. Fixture Cleaning The cleaning must be carried out periodically to optimize light output. Cleaning frequency depends on the environment in which the fixture operates: damp, smoky or particularly dirty surrounding can cause greater accumulati...

[Page 18] ACME TB-1010QW II

17A ...

[Page 19] ACME TB-1010QW II

Declaration of Conformity We declare that our products (lighting equipments) comply with the following specification and bears CE mark in accordance with the provision of the Electromagnetic Compatibility (EMC) Directive 89/336/EEC. ...

[Page 20] ACME TB-1010QW II

Innovation, Quality, Performance ...