Acme MP-90 RGBW User Manual

Download or browse on-line these Operation & User’s Manual for ACME MP-90 RGBW DJ Equipment.

ACME MP-90 RGBW Manual Information:

This manual for ACME MP-90 RGBW, given in the PDF format, is available for free online viewing and download without logging on. The guide contains 16 pages, and the size of the file at download is . The document type is Operation & User’s Manual.

Download Manual

Summary of Contents:

[Page 1] ACME MP-90 RGBW

MP-90 RGBW User Manual Please read the instructions carefully before use ...

[Page 2] ACME MP-90 RGBW

TABLE OF CONTENTS 1. Safety Introductions .................................................................................................. 2 2.Technical Specifications .............................................................................

[Page 3] ACME MP-90 RGBW

1. Safety Introductions WARNING  Please keep this User Guide for future consultation. If you sell the unit to another user, be sure that they also receive this instruction booklet.  All fixtures are intact from the manufac...

[Page 4] ACME MP-90 RGBW

 Do not touch any wire during operation as there might be a hazard of electric shock.  Avoid power wires together around other cables.  Disconnect mains power before fuse/lamp replacement or servicing.  Replace fuse only with the...

[Page 5] ACME MP-90 RGBW

2.Technical Specifications  Voltage : 100-240V~ 50/6 0 Hz  LED: 3W CREE XP-E LED x 90pcs, Red:18PCS; Green:24PCS; Blue:24PCS; White:24PCS.  Fuse: T 6.3A  Power consumption : 280W  Dimension : 234 x 299 x ...

[Page 6] ACME MP-90 RGBW

○ 3 Button: MENU To select the programming functions DOWN To go backward in the selected functions UP To go forward in the selected functions ENTER To confirm the selected functions ○ 4 Microphone: Receive music for the sou...

[Page 7] ACME MP-90 RGBW

6A ...

[Page 8] ACME MP-90 RGBW

DMX 512 Address Setting Press the MENU button up to when is shown on the display. Pressing ENTER button and the display will blink. Use DOWN and UP button to change the DMX 512 address. Once the address has been selected, press ENTER butto...

[Page 9] ACME MP-90 RGBW

setup or automatically exit menu mode without any change after one minute. To go back to the last function without any change press the MENU button. Optically Linear Square Law Inverse Square Law S-curve Optically Li...

[Page 10] ACME MP-90 RGBW

the display will blink. Use DOWN and UP button to select (display always on) or (display off 20 seconds after exit menu) mode. Once select, press ENTER button to setup or exit menu mode without any change after one minute. Back to the funct...

[Page 11] ACME MP-90 RGBW

Fixture Hours Press the MENU button up to when is blinking on the display. Pressing ENTER button and the display will show the number of working hours of the unit. To go back to the functions press the MENU button. Software version Pres...

[Page 12] ACME MP-90 RGBW

has been selected, press and keep ENTER button pressed up to when the display stops blinking or storing automatically one minute later. To go back to the functions without any change press the MENU button again. If you use please refer to the f...

[Page 13] ACME MP-90 RGBW

5. DMX512 Configuration Mode 4&5; Mode 7: 12A ...

[Page 14] ACME MP-90 RGBW

6. DMX512 Connections The DMX512 is widely used in intelligent lighting control, with a maximum of 512 channels. 1. Connect the fixture together in a “daisy chain” by XLR plug cable from the output of the fixture to the input of the...

[Page 15] ACME MP-90 RGBW

7. Troubleshooting Following are a few common problems that may occur during operation. Here are some suggestions for easy troubleshooting: A. The fixture does not work, no light 1. Check the connection of power and main fuse. 2. Measure...

[Page 16] ACME MP-90 RGBW

Innovation, Quality, Performance Declaration of Conformity We declare that our products (lighting equipments) comply with the following specification and bears CE mark in accordan...