NEC NP-PX700W Manual

Download or browse on-line these Command Manual for NEC NP-PX700W Projector.

NEC NP-PX700W Manual Information:

This manual for NEC NP-PX700W, given in the PDF format, is available for free online viewing and download without logging on. The guide contains 60 pages, and the size of the file at download is . The document type is Command Manual.

Download Manual

More Manuals:

In case you failed to obtain relevant information in this document, please, look through related operating manuals and user instructions for NEC NP-PX700W. Just click one of the links below to go to the selected manual:

Summary of Contents:

[Page 1] NEC NP-PX700W

====================================================================== Control Commands for NEC Projector (Basic) Rev 11.03.11a Copyright (C) NEC Display Solutions, Ltd. 2002-2011 ---------------------------------------------------------------...

[Page 2] NEC NP-PX700W

====================================================================== Contents 1. Projector Control 2. Connection Method 3. Interface Conditions 4. List of Commands 5. Command Descriptions 6. Table of Response Error Codes ==...

[Page 3] NEC NP-PX700W

[P350X/P350W/P420X Series] STANDBY MODE: "POWER-SAVING" Control Command Serial port Wired LAN port Wireless LAN unit POWER ON Yes No No Yes: Supported No: Not supported =============================================================...

[Page 4] NEC NP-PX700W

(1) (2) (3-1) (3-2) (3-3) (3-4) GT5000/GT6000 Yes Yes Yes Yes Yes No GT1150/GT2150 Yes No Yes Yes Yes No HT410/HT510 Yes No No No No No HT1000/HT1100 Yes No No No No No LT180 Yes No No No No No LT25/LT30/LT35 Yes No No No No No LT220/LT240/LT260 Yes ...

[Page 5] NEC NP-PX700W

( CAUTION ) Before making connections, set the standby mode of the projector to "NORMAL" or "Idol mode". The projector cannot use the control commands in the power-saving condition, but the following model can use ...

[Page 6] NEC NP-PX700W

[ GT/LT80/MT/NP1000/VT (except VT70/VT80/VT90)/NP3150/NP905/NP600/NP4000/NP3250/NP610/NP2200/NP216/M300/P420/U300/V300 ] The PC CONTROL connector is a D-SUB 9-pin connector. 1 2 To TxD of PC 3 To RxD of PC 4 5 To GND...

[Page 7] NEC NP-PX700W

This is an identification data assigned to each command. Command : This sets an identification data assigned to each command to send it. ( See each command description.) Response : This returns the 6th bit of received ID1 as HIGH. For...

[Page 8] NEC NP-PX700W

* When the controller is connected with the projector on a one-to-one basis Broadcast notification is recommended. * When the controller is connected with multiple projectors To control a certain projector, use "individual notificat...

[Page 9] NEC NP-PX700W

4-2. Data portion of response ********************************************************************** For ACK This returns ACK without adding data portion to the command that does not request data. This returns ACK with adding data ...

[Page 10] NEC NP-PX700W

02H : Adjustment failed * When a logo transfer error occurs 00H : Start is not requested 01H : Cannot process due to storing 02H : Exceeds the total number of blocks required ...

[Page 11] NEC NP-PX700W

==================================================================== 4. List of Commands ---------------------------------------------------------------------- * Example for command ------------------------------------------------------...

[Page 12] NEC NP-PX700W

05 : MT860 06 : WT600/WT610/WT615 07 : GT5000 08 : LT240K/LT260K 09 : GT6000 10 : HT1100 11 : VT770 12: HT410/HT510 (HT10 Series) 13 : LT245/LT265 14 : LT280/LT380 15 : LT180 16 : VT37/VT47/VT470/VT57/VT570/VT575/VT670/VT676 (...

[Page 13] NEC NP-PX700W

Meaning of Symbols -------------------------------------------------------------------- * Supported ! Is available depending on model's version - Not Supported Command Name 25 26 27 29 30 31 32 33 34 35 36 37 38 39 40 0...

[Page 14] NEC NP-PX700W

Command Name 1 2 3 4 5 6 7 8 9 10111213141516171819202122232428 006. RUNNING SENSE ***********-**-- -**- --*** 007. COMMON DATA REQUEST ***********-**-- -**- --*** 009. ERROR STATUS REQUEST **************-- -***...

[Page 15] NEC NP-PX700W

In case of NP216 series 20H In case of V300 series 20H In case of VT series 40H In case of NP600 series 40H In case of NP610 series 40H In case of NP2200 series 40H In case of M300 serie...

[Page 16] NEC NP-PX700W

DATA01 Status of operation Bit 7: Power On/Off processing 0 = No execution (Normal condition) 1 = During execution Bit 6: Selecting signal processing ...

[Page 17] NEC NP-PX700W

00H: Idling 01H: Power On DATA05 Cooling processing 00H: No execution (Normal condition) 01H: During execution DATA06 Indication signal number (Entry lis...

[Page 18] NEC NP-PX700W

DATA32 Freeze Status (!2) 00H : OFF 01H : ON FFH : Not Supported DATA33 Test pattern display 1 00H : No display (Normal condition) 00H Other : Displaying (Pattern...

[Page 19] NEC NP-PX700W

DATA68 Selecting signal processing 00H : No execution (Normal condition) 01H : During execution DATA69 Status of operation 00H : Idling 04H : Power On ...

[Page 20] NEC NP-PX700W

Data01 Data70 Data71 01H 00H 03H MT1060/MT1065 01H 01H 03H MT860 01H 02H 03H MT1075 01H 00H 06H NP1000/NP2000 02H 00H 03H LT240/LT260 02H 01H 03H LT220 02H 02H 03H LT240K/LT260K 02H 00H 05H LT245/LT265 02H 00H 06H LT380 02H 01H 06H LT280 03H 00H 04H ...

[Page 21] NEC NP-PX700W

DATA72 PC Card insertion 00H : Not inserted 01H : Inserted DATA73 USB Mouse connection 00H : Not connected ...

[Page 22] NEC NP-PX700W

009. ERROR STATUS REQUEST ********************************************************************** Function: This command acquires the error information occurring with the projector. Command: 00H 88H 00H 00H 00H 88H Response: At the ...

[Page 23] NEC NP-PX700W

Supplement: (!) LT/LT80/HT: "None" 015. POWER ON ********************************************************************** Function: This command switches on the main power of the projector. Command: 02H 00H 00H 00H 00H ...

[Page 24] NEC NP-PX700W

DATA02 Switching number --------------------------------------------------------- When the switching object is the "Signal list", the signal list number is specified. (0…99) ---------------...

[Page 25] NEC NP-PX700W

Response: At the time of a success 22H 03H 01H xxH 01H DATA01 CKS (*1) (*2) (*3) Data Portion Contents ------------------------------------------------------------------- DATA01...

[Page 26] NEC NP-PX700W

022. SOUND MUTE ON ********************************************************************** Function: This command mutes the sound. Command: 02H 12H 00H 00H 00H 14H Response: At the time of a success 22H 12H 01H xxH 00H CK...

[Page 27] NEC NP-PX700W

025. ONSCREEN MUTE OFF ********************************************************************** Function: This command cancels the blanking of the on-screen display. Command: 02H 15H 00H 00H 00H 17H Response: At the time of a s...

[Page 28] NEC NP-PX700W

DATA03 : 00H (direct settings) 01H (increment/decrement) DATA04 : lower data (8bit) DATA05 : upper data (8bit) ex.1) volume direct setting (value = 20) DATA01 : 05H (Volume) ...

[Page 29] NEC NP-PX700W

------------------------------------------------------------------- DATA01 .. 02 Results 0000H : Normal 0000H Other : Error Response: At the time of a failure A3H 10H 01H xxH 02H DATA01 DATA02 ...

[Page 30] NEC NP-PX700W

DATA04 DATA05 Aspect Ratio 4:3 (Window) 00H 00H Aspect Ratio Normal / Auto (NP600, NP610, NP2200, NP62, NP64, NP216, P420, PA600, U300, V300 Series) 00H 00H Aspect Ratio 1.25:1(5:4) 00H 00H Aspect Ratio Letter Box (PA600, PX750 Series) 01H 00H Aspe...

[Page 31] NEC NP-PX700W

Supplement: (!) Lamp Hour Meter This is the timer for normal lamp mode conversion. Lamp Timer Acquisition Examples DATA83 DATA84 DATA85 DATA86 : Lamp Timer 00H 00H 00H 00H : Total 0 seconds C0H 65H ...

[Page 32] NEC NP-PX700W

2) Punch in DATA12 DATA11 DATA10 DATA09 (006DDD00) 3) Change from HEX to Decimal - value will change to 7200000 seconds Lamp remaining time (in terms of Normal mode values) = (7200000 - 10800) / 3600 = 1997 hour 037-2. ...

[Page 33] NEC NP-PX700W

to appear (in terms of Eco mode values) 10H : Remaining time until inhibition of lamp usage (in terms of specified values) 11H : Remaining time until inhibition of lamp...

[Page 34] NEC NP-PX700W

Function: This command acquires the information on the projector lamp. Command: 03H 9BH 00H 00H 03H DATA01 DATA02 DATA03 CKS (*3) Data Portion Contents -----------------...

[Page 35] NEC NP-PX700W

Lamp Use Warning Starting Time 2000[H] Model. X = 100 - ((2100 * 100) / 2000) = -5[%] (!2) Lamp Hour Meter This is the timer for normal lamp mode conversion. (!3) Lamp usage time This is the lamp total usage. It is d...

[Page 36] NEC NP-PX700W

00H : Normal 01H : Error Response: At the time of a failure A3H B1H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) 046. ...

[Page 37] NEC NP-PX700W

01H : Error Response: At the time of a failure A3H B1H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) =====================================================...

[Page 38] NEC NP-PX700W

Key number DATA01 DATA02 Key name -------------------------------------------- 1 01H 00H POWER 2 02H 00H POWER ON (!!) ...

[Page 39] NEC NP-PX700W

81 51H 00H S-VIDEO1 (!!) 82 52H 00H S-VIDEO2 83 53H 00H DIGITAL1 84 54H 00H DIGITAL2 ...

[Page 40] NEC NP-PX700W

Command example: * Sending the AUTO key code 02H 0FH 00H 00H 02H 05H 00H 18H * Sending the AUTO (SHORT) key code 02H 0FH 00H 00H 02H DDH 00H F0H ------------------------------------------ * cycle/toggle volume mu...

[Page 41] NEC NP-PX700W

051. CARBON SAVINGS INFORMATION REQUEST ********************************************************************** Function: This command acquires the Carbon Saving values on the projector. Command: 03H 9AH 00H 00H 01H DATA01 CKS ...

[Page 42] NEC NP-PX700W

------------------------------------------------------------------- DATA01 Target 00H : Use Point on Signal Change 01H : Picture mute during lens shift DATA02 Setting Value ...

[Page 43] NEC NP-PX700W

DATA09 Current value (Upper ranking 8 bits) DATA10 .. 13 Reserved Response: At the time of a failure A3H 04H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) ...

[Page 44] NEC NP-PX700W

4CH 07H Color Correction / Yellow 4CH 08H Color Correction / Magenta 4CH 09H Color Correction / Cyan 4CH 0AH Color Correction / White 4DH 00H Through 4EH 00H Ref. Auto White / Color Temp R 4EH 01H Ref. Auto White / Color Temp G 4EH 02H Ref. Aut...

[Page 45] NEC NP-PX700W

077. MUTE CONTROL ********************************************************************** Function: This command controls the mute of picture, sound and on-screen. Command: 02H 1AH 00H 00H 02H DATA01 DATA02 CKS ...

[Page 46] NEC NP-PX700W

DATA01 DATA02 DATA03 Current Models 08H 00H 10H NP4100 08H 01H 10H NP4100W 11H 00H 12H NP64 11H 03H 12H NP43 13H 01H 10H M300X 13H 02H 10H M300W 13H 05H 10H M260X 13H 06H 10H M260W 13H 00H 11H P420X 13H 01H 11H P350X 13H 02H 11H P350W 14H 02H 10H U30...

[Page 47] NEC NP-PX700W

Legacy Models 01H 00H 03H MT1060/MT1065 01H 01H 03H MT860 01H 02H 03H MT1075 01H 00H 06H NP1000/NP2000 02H 00H 03H LT240/LT260 02H 01H 03H LT220 02H 02H 03H LT240K/LT260K 02H 00H 05H LT245/LT265 02H 00H 06H LT380 02H 01H 06H LT280 03H 00H 06H VT80 Se...

[Page 48] NEC NP-PX700W

DATA05 Calendar function 00H : No function 01H or 03H : Timer function, sleep timer function 02H : Sleep timer function DATA06 .. 32 Reserved Response: At the time of a fai...

[Page 49] NEC NP-PX700W

(*1) (*2) (*4) (*3) 078-3. INPUT STATUS REQUEST ********************************************************************** Function: This command acquires the status of input signal of th...

[Page 50] NEC NP-PX700W

01H : Displaying DATA07 ..08 Reserved DATA09 Indicate Contents 00H = Picture signal displaying 01H = No signal 02H = Viewer displaying 03H = T...

[Page 51] NEC NP-PX700W

078-5. MODEL NAME REQUEST ********************************************************************** Function: This command acquires the model name of the projector. Command: 00H 85H 00H 00H 01H 04H 8AH Response: At the time of a su...

[Page 52] NEC NP-PX700W

Function: This command controls the freeze. Command: 01H 98H 00H 00H 01H DATA01 CKS Operation types DATA01: 00H : Reserved 01H : Freeze start 02H : Freeze cancel Response: At the time of a su...

[Page 53] NEC NP-PX700W

Data Portion Contents ------------------------------------------------------------------- DATA01 C5H fixed DATA02 Acquisition Object 00H : MODE 01H : POSITION 02H : SOU...

[Page 54] NEC NP-PX700W

if DATA02 is SOURCE(02H) 00H : OFF 01H : VIDEO 02H : S-VIDEO Response: At the time of a success 23H B1H 01H xxH 03H DATA01 DATA02 DATA03 CKS ...

[Page 55] NEC NP-PX700W

111. AUTO ADJUST EXECUTE2 ********************************************************************** Function: This command executes the Auto Adjust. Command: 03H BAH 00H 00H 01H 00H BEH Response: At the time of a success 23H BA...

[Page 56] NEC NP-PX700W

DATA02 DATA03 DATA13 DATA14 Current Models 03H 08H 00H 10H NP4100 03H 08H 01H 10H NP4100W FFH 11H 00H 12H NP64 FFH 11H 03H 12H NP43 FFH 13H 01H 10H M300X FFH 13H 02H 10H M300W FFH 13H 05H 10H M260X FFH 13H 06H 10H M260W FFH 13H 00H 11H P420X FFH 13H ...

[Page 57] NEC NP-PX700W

Legacy Models 00H 01H 00H 03H MT1060/1065 00H 01H 02H 03H MT860 00H 01H 02H 03H MT1075 00H 01H 00H 06H NP1000/NP2000 00H 02H 00H 03H LT240/LT260 00H 02H 01H 03H LT220 00H 02H 02H 03H LT260K 00H 02H 00H 05H LT245/LT265 00H 02H 00H 06H LT380 0...

[Page 58] NEC NP-PX700W

DATA15 ... 16 Reserved Response: At the time of a failure A0H BFH 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) 305-3. PROJECTOR INFORMATION REQUEST *******...

[Page 59] NEC NP-PX700W

0CH : DIGITAL2 0DH : SCART 10H : AUTO FFH : Not Source Input Other : Not Support DATA06 Indication signal type (...

[Page 60] NEC NP-PX700W

====================================================================== 6.1. Response ---------------------------------------------------------------------- * At the time of a success (ACK) This returns ACK without adding data portion to the co...