Hitachi CP-X9110 User Manual

[Page 1] Hitachi CP-X9110

1 • Mac ® is a registered trademark of Apple Inc. • Windows ® , DirectDraw ® and Direct3D ® are registered trademarks of Microsoft Corporation in the U.S. and/or other countries. • VESA and DDC are trademarks of the Video Electronics...

[Page 2] Hitachi CP-X9110

2 Contents Introduction ...............3 Features ......................3 Checking the contents of package ....3 Part names ....................4 Projector, Control panel and Indicators, Ports, Remote control Setting up .................7 Instal...

[Page 3] Hitachi CP-X9110

3 Introduction • Keep the original packing materials, for future reshipment. Be sure to use the original packing materials when moving the projector. Use special caution for the lens. • The projector may make a rattling sound when tilted, moved...

[Page 4] Hitachi CP-X9110

4 Introduction Projector (1) Dust protector (2) Remote sensors( 19) (3) Elevator feet (x2) (29) (4) AC (AC inlet) (17) (5) Holes for Cable Tie(14) (6) Security slot (16) (7) Security bar (16) (8) Control panel (5) (9) Status Mon...

[Page 5] Hitachi CP-X9110

5 Control panel and Indicators (1) STANDBY/ON button ( 26) (2) INPUT button (27) (3) MENU button (48) (4) LENS SHIFT button (30) (5) ZOOM button (30) (6) FOCUS - / + buttons (30) (7) SHUTTER button (43) (8) FUNCTION button (...

[Page 6] Hitachi CP-X9110

6 Introduction Part names (continued) • Any button marked with “*” is not supported on this projector ( 27). • Each time you press any button (except ID buttons), the ID button of current selected ID number will light ( 18). NO...

[Page 7] Hitachi CP-X9110

7 Setting up Setting up Install the projector according to the environment and manner the projector will be used in. For the case of installation in a special state such as ceiling mount, the specied mounting accessories ( Specications in ...

[Page 8] Hitachi CP-X9110

8 Setting up Arrangement (continued) WARNING (continued on next page) ►Install the projector where you can access the power outlet easily. If an abnormality should occur, unplug the projector urgently. Otherwise it could cause a re or electric...

[Page 9] Hitachi CP-X9110

9 Setting up Arrangement (continued) ►Place the projector in a cool place with sufcient ventilation. The projector may shutdown automatically or may malfunction if its internal temperature is too high. Using a damaged projector could result in...

[Page 10] Hitachi CP-X9110

10 Setting up Connecting with your devices Before connecting the projector to a device, consult the manual of the device to conrm that the device is suitable for connecting with this projector and prepare the required accessories, such as a cabl...

[Page 11] Hitachi CP-X9110

11 Setting up Connecting with your devices (continued) • Before connecting the projector to a computer, consult the computer’s manual and check the compatibility of the signal level, the synchronization methods and the display resolution output...

[Page 12] Hitachi CP-X9110

12 Setting up Connecting with your devices (continued) (continued on next page) ► Before connecting the projector to a network system be sure to obtain the consent of the administrator of the network. ► Do not connect the LAN port to any network...

[Page 13] Hitachi CP-X9110

13 Setting up • The HDMI ports of this model are compatible with HDCP (High-band- width Digital Content Protection) and therefore capable of displaying video signals from HDCP compatible DVD players or the like. - The HDMI ports support the follo...

[Page 14] Hitachi CP-X9110

14 Setting up Connecting with your devices (continued) • To use a wired remote control, connect a wired remote control to the REMOTE CONROL IN port. You can also connect another projector to the REMOTE CONROL OUT port to control it from the wired...

[Page 15] Hitachi CP-X9110

15 1. Loosen the screw (marked with triangle) on the bottom left of the WIRELESS port. Tab 2. Insert the tab of the cover into the hole at the upper right of the WIRELESS port in the direction of the arrow. 3. Align the screw holes on the projec...

[Page 16] Hitachi CP-X9110

16 Using the security bar and slot A commercially available anti-theft chain or wire can be attached to the security bar on the projector. Refer to the  gure to choose an anti-theft chain or wire. Also this product has the security slot for th...

[Page 17] Hitachi CP-X9110

17 Setting up Connecting to a power supply ►Do not connect the projector to a power supply while no lens unit is attached to it. ►Please use extra caution when connecting the power cord, as incorrect or faulty connections may result in  re a...

[Page 18] Hitachi CP-X9110

18 Remote control Installing the batteries Please insert the batteries into the remote control before using it. If the remote control starts to malfunction, try to replace the batteries. If you will not use the remote control for long period, remov...

[Page 19] Hitachi CP-X9110

19 About the remote control signal The remote control works with the projector’s remote sensor. This projector has two remote sensors on the front and back sides. The sensors can sense signals within the following range: 60 degrees (30 degrees ...

[Page 20] Hitachi CP-X9110

20 Status Monitor Status Monitor Displaying the condition of the projector The Status Monitor is the sub LCD in the side panel that displays the information in the following. If no buttons are pressed, the Status Monitor displays the current status ...

[Page 21] Hitachi CP-X9110

21 Status Monitor You can switch the display to see Error log , Lamp log , Filter log and Network information. •When Normal or Warning is displayed: 1. Press one of the following buttons. 1) FUNCTION button on the control panel 2) ENTER button o...

[Page 22] Hitachi CP-X9110

22 Status Monitor  In a normal state The Status Monitor displays the state of the projector in three lines. 1st line : Displays the condition of the projector. While the lamp is on, the selected port is displayed. Displayed conditions are ...

[Page 23] Hitachi CP-X9110

23 Status Monitor The current status (Warnings and Errors) The Status Monitor displays a warning or an error with larger letters. When it is displayed, refer to the table "Related messages"( Troubleshooting ) or “Regarding the indic...

[Page 24] Hitachi CP-X9110

24 Status Monitor Lamp log Displays the usage time of the lamp1 & 2, and executes Lamp Time Reset. You can display previous logs by pressing the ▲ button. Usage time; •Displays remaining cycle time and the lamp 1 & 2 usage time. Lamp T...

[Page 25] Hitachi CP-X9110

25 Filter log Displays the usage time of the lter and projector. You can display previous logs by pressing the ▲ button. • The system usage time is the total lamp time from the projector is manufactured. It cannot be reset. NOTE Network info...

[Page 26] Hitachi CP-X9110

26 Power on/off 1. Make sure that the power cord is rmly and correctly connected to the projector and the outlet. Turning on the power 2. Make sure that the POWER indicator is lighted in steady orange (106). 3. Press STANDBY/ON button on th...

[Page 27] Hitachi CP-X9110

27 Operating Selecting an input signal COMPUTER IN1 COMPUTER IN2 LAN HDMI 1 HDMI 2 HDBaseT VIDEO        DVI-D  Buttons for input ports 1. Activate your signal source. Turn the signal source on, to send signal to the project...

[Page 28] Hitachi CP-X9110

28 Selecting an aspect ratio  For a computer signal CP-X9110: NORMAL  4:3  16:9  16:10 CP-WX9210, CP-WU9410: NORMAL  4:3  16:9  16:10  NATIVE  For a video signal CP-X9110: 4:3  16:9...

[Page 29] Hitachi CP-X9110

29 ►Do not place the projector with an inclination exceeding 5 degrees. The projector leaned exceeding the limit could cause malfunction and shorten the life of the projector. CAUTION Lengthening or shortening the length of the elevator feet shif...

[Page 30] Hitachi CP-X9110

30 The ZOOM or FOCUS dialog will appear when you press any of the buttons from ZOOM, ZOOM -, ZOOM +, FOCUS + and FOCUS -. 1. Use the ZOOM + / - buttons to adjust the screen size. 2. Use the FOCUS + / - buttons to focus the picture. Adjusting ...

[Page 31] Hitachi CP-X9110

31 Adjusting the lens (continued) This projector is equipped with memory functions for the lens adjustments (ZOOM, FOCUS, LENS SHIFT and LENS TYPE). Up to 3 sets of adjustments can be stored. To utilize the lens memory feature, press the LOAD or ...

[Page 32] Hitachi CP-X9110

32 1. Press AUTO button on the remote control. Pressing this button performs the following. Using the automatic adjustment feature  For a computer signal The vertical position, the horizontal position and the horizontal phase will be automat...

[Page 33] Hitachi CP-X9110

33 Operating Other buttons HDCR: Displays the HDCR menu ( 56 ) . C.WHEEL: Displays the COOR WHEEL menu ( 56 ) . OSD: Displays the OSD MESSAGE menu ( 77 ) , and it switches the function by pressing the button again. ON  SILENT...

[Page 34] Hitachi CP-X9110

34 KEYSTONE: allows you to adjust the vertical and horizontal keystone. PERFECT FIT: allows you to adjust each of the screen corners and sides to correct the distortion. • The menu or dialog will automatically disappear after several second...

[Page 35] Hitachi CP-X9110

35 Correcting the distortion (continued) • When the zoom adjustment is set to the TELE (telephoto focus), this function may be excessive. This function should be used when the zoom ad- justment is set to the full WIDE (wide-angle focus) whenever p...

[Page 36] Hitachi CP-X9110

36 Correcting the distortion (continued) 4. This projector is equipped with a memory feature for PERFECT FIT adjustment. Up to 3 sets of adjustments can be stored. ● SAVE1~3: To store the current PERFECT FIT adjustment, select one of the &qu...

[Page 37] Hitachi CP-X9110

37 Using the EDGE BLENDING feature A part of projected image from two projectors can be superimposed to one large screen by EDGE BLENDING function ( 66 ) . 1. PATTERN Select PATTERN with ▲/▼ buttons. Displayed pattern [Off/1/2] can be switche...

[Page 38] Hitachi CP-X9110

38 Operating 2.2 Specifying Blending Region Select one of the four sides with ▲/▼/ ◄/► buttons and press ENTER or Input button. Blending Region can be speci ed for left and right sides with ◄/► but- tons and for top and bottom si...

[Page 39] Hitachi CP-X9110

39 3. Cropping When inputting the same image to each of two projectors, Cropping function enables two projectors to cut out a part of input image and display one image on a large screen. 3.1 Displaying Cropping Menu Select CROPPING with ▲/▼ b...

[Page 40] Hitachi CP-X9110

40 Operating 4. Selecting Blending Level Select BLENDING LEVEL with ▲/▼ buttons. [NORMAL/BRIGHT/DARK] can be selected with ◄/► buttons . Adjust the brightness of Blending Region according to the settings. 3. Cropping (continued) 3.4 Adjust...

[Page 41] Hitachi CP-X9110

41 Operating Using the WARPING feature Using the Camera Feedback (BLENDING) feature Projection on a cube can be performed by WARPING function. This function is operated by using dedicated PC tool, "Warping Tool". PC and projector are requir...

[Page 42] Hitachi CP-X9110

42 1. Using the magnify feature 2. 3. 4. Press the MAGNIFY ON button on the remote control. The picture will be magnied, and the MAGNIFY dialog will appear on the screen. When the MAGNIFY ON button is pressed for the rst time after the pr...

[Page 43] Hitachi CP-X9110

43 1. Press the SHUTTER button on the control panel. or on the remote control. The mechanical lens shade closes and the screen turns to black. The SHUTTER indicator on the projector blinks in yellow while the shade is closed. To open the shade ...

[Page 44] Hitachi CP-X9110

44 The PbyP / PinP is a function for displaying two different picture signals on a screen that is separated into main and sub areas for each signal. PbyP (Picture by Picture) / PinP (Picture in Picture) PbyP button Normal mode PbyP mode main area...

[Page 45] Hitachi CP-X9110

45 PbyP (Picture by Picture) / PinP (Picture in Picture) (continued) The position of the main area can be toggled with the ◄/► buttons when the setting information is displayed on the screen. The yellow frame will move together with it.  C...

[Page 46] Hitachi CP-X9110

46 Press any button to select an input port on the remote control or press the INPUT button on the control panel. A dialog box to select the input signal for the main area will be displayed. Choose a signal using the ▲/▼ buttons. To change the...

[Page 47] Hitachi CP-X9110

47 Using ▲/▼ buttons on the remote control changes the size of main area in PbyP mode.  Changing the size of main area in PbyP mode Press the PbyP button on the remote control or follow the procedure below. EASY MENU > ADVANCED MENU &...

[Page 48] Hitachi CP-X9110

48 1. To start the MENU, press the MENU button. The MENU you last used (EASY or ADVANCED) will appear. EASY MENU has priority to appear just after powered on. Using the menu function 2. (1) Use the ▲/▼ cursor buttons to select an item to oper...

[Page 49] Hitachi CP-X9110

49 Using the menu function (continued) 3. To close the MENU, press the MENU button again or select EXIT and press the ◄ cursor button or ENTER button. Even if you do not do anything, the dialog will automatically disappear after about 30 seconds....

[Page 50] Hitachi CP-X9110

50 Using the menu function (continued) Containing items of each menu The items contained in the menus are as below; Menu Items EASY MENU (  51 ) ASPECT, KEYSTONE, PERFECT FIT, PICTURE MODE, ECO MODE, INSTALLATION, RESET, FILTER TIME, LANGUAGE, A...

[Page 51] Hitachi CP-X9110

51 EASY MENU EASY MENU From the EASY MENU, items shown in the table below can be performed. Select an item using the ▲/▼ cursor buttons. Then perform it according to the following table. Item Description ASPECT Using the ◄/► buttons switche...

[Page 52] Hitachi CP-X9110

52 EASY MENU Item Description PICTURE MODE (continued) • Lines or other noise might appear on the screen when this function is operated, but it is not a malfunction. • DICOM SIM. is the projector's DICOM ® ("Digital Imaging and Co...

[Page 53] Hitachi CP-X9110

53 PICTURE menu PICTURE menu From the PICTURE menu, items shown in the table below can be performed. Select an item using the ▲/▼ cursor buttons, and press the ► cursor button or ENTER button to execute the item. Then perform it according t...

[Page 54] Hitachi CP-X9110

54 PICTURE menu Item Description PICTURE QUALITY Selecting this item displays the PICTURE QUALITY menu. Select an item using the ▲/▼ buttons, and press the ► button or the ENTER button on the remote control to execute the item. PICTURE MODE...

[Page 55] Hitachi CP-X9110

55 PICTURE menu Item Description PICTURE QUALITY GAMMA (continued) Selecting a mode whose name includes CUSTOM and then pressing the ► button or the ENTER button displays a dialog to aid you in adjusting the mode. This function is useful when ...

[Page 56] Hitachi CP-X9110

56 PICTURE menu Item Description PICTURE QUALITY ACCENTUALIZER This feature is only available when USER-1 / USER-2 / USER-3 is selected. ACCENTUALIZER is a function to improve the legibility. Using the ◄/► buttons adjusts the sharpness. Weak �...

[Page 57] Hitachi CP-X9110

57 PICTURE menu Item Description MY MEMORY This projector has 4 memories for adjustment data (for all the items of the PICTURE menu). Selecting a function using the ▲/▼ buttons and pressing the ► or ENTER button performs each function. SAVE-1...

[Page 58] Hitachi CP-X9110

58 IMAGE menu IMAGE menu From the IMAGE menu, items shown in the table below can be performed. Select an item using the ▲/▼ cursor buttons, and press the ► cursor button or ENTER button to execute the item. Then perform it according to the ...

[Page 59] Hitachi CP-X9110

59 IMAGE menu Item Description OVER SCAN Using the ◄/► buttons adjusts the over-scan ratio. Small (It magnies picture)  Large (It reduces picture) • This item can be selected only for a video and component video signal. • For an HDMI...

[Page 60] Hitachi CP-X9110

60 IMAGE menu Item Description H PHASE Using the ◄/► buttons adjusts the horizontal phase to eliminate icker. Right  Left • This item can be selected only for a computer signal or a component video signal. This function is unavailabl...

[Page 61] Hitachi CP-X9110

61 INPUT menu INPUT menu From the INPUT menu, items shown in the table below can be performed. Select an item using the ▲/▼ cursor buttons, and press the ► cursor button or ENTER button to execute the item. Then perform it according to the ...

[Page 62] Hitachi CP-X9110

62 INPUT menu Item Description VIDEO FORMAT The video format for VIDEO port can be set. Using the ◄/► buttons switches the mode for video format. AUTO  NTSC  PAL  SECAM N-PAL  M-PAL  NTSC4.43 • This it...

[Page 63] Hitachi CP-X9110

63 INPUT menu Item Description COMPUTER IN The computer input signal type for COMPUTER IN1 and IN2 ports can be set. (1) Use the ▲/▼ buttons to select the COMPUTER IN port to be set. (2) Use the ◄/► buttons to select the computer input s...

[Page 64] Hitachi CP-X9110

64 INPUT menu Item Description RESOLUTION The resolution for the COMPUTER IN1 and COMPUTER IN2 input signals can be set on this projector. (1) In the INPUT menu select the RESOLUTION using the ▲/▼ buttons and press the ► button. The RESOLUT...

[Page 65] Hitachi CP-X9110

65 Item Description PbyP / PinP SETUP PinP POSITION Using ▲/▼ buttons on the remote control changes the position of sub area in PinP mode (  47 ). PbyP / PinP FRAME LOCK Select the screen that enables FRAME LOCK function when using PbyP or ...

[Page 66] Hitachi CP-X9110

66 SETUP menu From the SETUP menu, items shown in the table below can be performed. Select an item using the ▲/▼ cursor buttons, and press the ► cursor button or ENTER button to execute the item. Then perform it according to the following t...

[Page 67] Hitachi CP-X9110

67 Item Description LAMP & FILTER Selecting this item displays the LAMP & FILTER menu. Select an item using the ▲/▼ buttons, and press the ► button or the ENTER button on the remote control to execute the item. ECO MODE Using the �...

[Page 68] Hitachi CP-X9110

68 Item Description LAMP & FILTER (continued) CYCLE TIME Using the ▲/▼ cursor buttons changes the CYCLE TIME. 6h  12h  18h  24  1 week Lamp switches according to the setting here. • This function i...

[Page 69] Hitachi CP-X9110

69 Item Description LAMP & FILTER (continued) FILTER TIME The lter time is the usage time of the air lter, counted after the last resetting. It is shown in the LAMP & FILTER menu. Pressing the RESET button on the remote control or the...

[Page 70] Hitachi CP-X9110

70 Item Description INSTALLATION Pressing the ►button displays the dialog for changing the INSTALLATION setting. FRONT / DESKTOP  REAR / DESKTOP  REAR / CEILING  FRONT / CEILING Use the ▲/▼ buttons to select...

[Page 71] Hitachi CP-X9110

71 Item Description MONITOR OUT While the image signal from the input port chosen in step (1) is projected, the image signal from the input port selected in step (2) is output to MONITOR OUT port. (1) Choose a picture input port using ▲/▼ ...

[Page 72] Hitachi CP-X9110

72 SCHEDULE menu Item Description DATE & TIME Set the DATE(Year/Month/Date) and Time(24-hour scale). SPECIFIC DATE Set specic date from 1 to 5. PROGRAM EDIT The TIME and EVENT for Program 1 to 16 can be editted.(  73) ■ How to setup the...

[Page 73] Hitachi CP-X9110

73 SCHEDULE menu ■ PROGRAM EDIT The TIME and EVENT for Program 1 to 16 can be editted. • RETURN Select this to go back to the top menu of the SCHEDULE. • SELECT Select from PROGRAM-01 to 16 to edit. Each PROGRAM can be setup up to 20 setting...

[Page 74] Hitachi CP-X9110

74 SCREEN menu SCREEN menu From the SCREEN menu, items shown in the table below can be performed. Select an item using the ▲/▼ cursor buttons, and press the ► cursor button or ENTER button to execute the item. Then perform it according to th...

[Page 75] Hitachi CP-X9110

75 SCREEN menu Item Description AUTO BLANK Using the ▲/▼ buttons switches the mode for the AUTO BLANK screen. BLUE  WHITE  BLACK • To avoid remaining as an afterimage, displayed image will change to the designated blank color...

[Page 76] Hitachi CP-X9110

76 SCREEN menu Item Description MyScreen This item allows you to capture an image for use as a MyScreen image which can be used as the BLANK screen and START UP screen. Display the image you want to capture before executing the following procedure...

[Page 77] Hitachi CP-X9110

77 SCREEN menu Item Description MyScreen Lock Using the ▲/▼ buttons turns on/off the MyScreen lock function. ON  OFF When the ON is selected, the item MyScreen is locked. Use this function for protecting the current MyScreen. • This funct...

[Page 78] Hitachi CP-X9110

78 SCREEN menu Item Description SOURCE NAME Each input port for this projector can have a name applied to it. (1) Use the ▲/▼ buttons on the SCREEN menu to select SOURCE NAME and press the ► or ENTER button. The SOURCE NAME menu will be dis...

[Page 79] Hitachi CP-X9110

79 SCREEN menu Item Description SOURCE NAME (continued) (6) The current name will be displayed on the rst line. Use the ▲/▼/◄/► buttons and the ENTER or INPUT button to select and enter characters. To erase 1 character at one time, pr...

[Page 80] Hitachi CP-X9110

80 SCREEN menu (continued on next page) Item Description C.C. (Closed Caption) The C.C. is the function that displays a transcript or dialog of the audio portion of a video, les or other presentation or other relevant sounds. It is required to ...

[Page 81] Hitachi CP-X9110

81 OPTION menu OPTION menu From the OPTION menu, items shown in the table below can be performed. Select an item using the ▲/▼ cursor buttons, and press the ► cursor button or ENTER button to execute the item, except for the items LAMP TIME...

[Page 82] Hitachi CP-X9110

82 OPTION menu Item Description DIRECT POWER ON Using the ▲/▼ buttons turns on/off the DIRECT POWER ON function. ON  OFF When set to the ON, the lamp in projector will be automatically turned on without the usual procedure (  26 ), onl...

[Page 83] Hitachi CP-X9110

83 OPTION menu Item Description MY BUTTON This item is to assign one of the following functions to MY BUTTON (1 to 4) on the remote control (  6 ). (1) Use the ▲/▼ buttons on the MY BUTTON menu to select a button from MY BUTTON - 1 to 4 and...

[Page 84] Hitachi CP-X9110

84 OPTION menu Item Description SERVICE Selecting this item displays the SERVICE menu. Select an item using the ▲/▼ buttons, and press the ► button or the ENTER button on the remote control to execute the item. ALTITUDE Using the ▲/▼ bu...

[Page 85] Hitachi CP-X9110

85 OPTION menu Item Description SERVICE (continued) LENS TYPE (1) Select the lens type currently used using the ▲/▼ buttons and press the ► or ENTER button. If AUTO is selected, the projector determines the lens type automatically. (2) A m...

[Page 86] Hitachi CP-X9110

86 OPTION menu Item Description SERVICE (continued) COLOR WHEEL LOCK Using the ▲/▼ buttons turns off/on the COLOR WHEEL LOCK. ON  OFF ON : COLOR WHEEL is locked and the settings can not be changed from PICTURE MENU. OFF : COLOR WHEEL sett...

[Page 87] Hitachi CP-X9110

87 OPTION menu Item Description SERVICE (continued) COMMUNICATION Selecting this item displays COMMUNICATION menu. In this menu, you can congure the serial communication settings of the projector using the CONTROL port. • Select an item usin...

[Page 88] Hitachi CP-X9110

88 OPTION menu Item Description SERVICE (continued) COMMUNICATION COMMUNICATION TYPE Select the communication type for transmission via the CONTROL port. NETWORK BRIDGE (WIRELESS)  NETWORK BRIDGE (WIRED)  OFF NETWORK BRIDGE: Select...

[Page 89] Hitachi CP-X9110

89 OPTION menu Item Description SERVICE (continued) COMMUNICATION (continued) SERIAL SETTINGS Select the serial communication condition for the CONTROL port. BAUD RATE 4800bps  9600bps  19200bps  38400bps PARITY NONE  ODD...

[Page 90] Hitachi CP-X9110

90 OPTION menu Item Description SERVICE (continued) COMMUNICATION (continued) RESPONSE LIMIT TIME Select the time period to wait for receiving response data from other device communicating by the NETWORK BRIDGE and the HALF-DUPLEX through the CONT...

[Page 91] Hitachi CP-X9110

91 OPTION menu Item Description SERVICE (continued) INFORMATION Selecting this item displays a dialog titled “INPUT_INFORMATION”. It shows the information about the current input. • The “FRAME LOCK” message on the dialog means the frame lo...

[Page 92] Hitachi CP-X9110

92 NETWORK menu See the Network Guide for details of NETWORK operation. Remember that incorrect network settings on this projector may cause trouble on the network. Be sure to consult with your network administrator before connecting to an existing...

[Page 93] Hitachi CP-X9110

93 Security Item Description SECURITY PASSWORD CHANGE (1) Use the ▲/▼ buttons on the SECURITY menu to select SECURITY PASSWORD CHANGE and press the ► button to display the ENTER NEW PASSWORD box. (2) Use the ▲/▼/◄/► buttons to en...

[Page 94] Hitachi CP-X9110

94 Security Item Description MyScreen PASSWORD The MyScreen PASSWORD function can be used to prohibit access to the MyScreen function and prevent the currently registered MyScreen image from being overwritten. 1 Turning on the MyScreen PASSWORD 1-...

[Page 95] Hitachi CP-X9110

95 Security Item Description PIN LOCK PIN LOCK is a function which prevents the projector from being used unless a registered Code is input. 1 Turning on the PIN LOCK 1-1 Use the ▲/▼ buttons on the SECURITY menu to select PIN LOCK and press th...

[Page 96] Hitachi CP-X9110

96 Security Item Description MY TEXT PASSWORD The MY TEXT PASSWORD function can prevent the MY TEXT from being overwritten. When the password is set for the MY TEXT; • The MY TEXT DISPLAY menu will be unavailable, which can prohibit changing the...

[Page 97] Hitachi CP-X9110

97 Security Item Description MY TEXT DISPLAY (1) Use the ▲/▼ buttons on the SECURITY menu to select the MY TEXT DISPLAY and press the ► or ENTER button to display the MY TEXT DISPLAY on/off menu. (2) Use the ▲/▼ buttons on the MY TEXT...

[Page 98] Hitachi CP-X9110

98 Security Item Description SECURITY INDICATOR Selecting this item displays the SECURITY INDICATOR dialog. Use the ▲/▼ buttons to select ON or OFF. ON  OFF When ON is selected while PIN LOCK is ON, the SECURITY indicator blinks in yellow...

[Page 99] Hitachi CP-X9110

99 Maintenance Maintenance Replacing the lamp A lamp has nite product life. Using the lamp for long periods of time could cause the pictures darker or the color tone poor. Note that each lamp has a different lifetime, and some may burst or burn...

[Page 100] Hitachi CP-X9110

100 ►Do not touch the interior of the projector, while the lamp is taken out. CAUTION 5. Insert the new lamp, and retighten rmly the 3 screws of the lamp that are loosened in the previous process to lock it in place. 6. While putting the int...