Simrad HS80/MX575C User Manual

Download or browse on-line these Operation & User’s Manual for Simrad HS80/MX575C Compass.

Simrad HS80/MX575C Manual Information:

This manual for Simrad HS80/MX575C, given in the PDF format, is available for free online viewing and download without logging on. The guide contains 55 pages, and the size of the file at download is . The document type is Operation & User’s Manual.

Download Manual

Summary of Contents:

[Page 1] Simrad HS80/MX575C

ENGLISH HS80/MX575C User Manual ...

[Page 2] Simrad HS80/MX575C

| 1 Preface | HS80 / MX575C User Manual Preface Disclaimer As Navico is continuously improving this product, we retain the right to make changes to the product at any time which may not be reflected in this version of the manual. Please contact yo...

[Page 3] Simrad HS80/MX575C

2 | Preface | HS80 / MX575C User Manual About this manual This manual is a reference guide for installing and using the HS80 / MX575C systems. The latest available manual version can be downloaded from our web sites. Important text that requires sp...

[Page 4] Simrad HS80/MX575C

| 3 Preface | HS80 / MX575C User Manual Contents 4 Introduction 4 Overview 5 Parts list 6 Installation 6 Mounting location 8 Mounting orientation 9 Mounting options 15 Ports 19 Powering the HS80/MX575C 20 Connecting the HS80/MX575C to external...

[Page 5] Simrad HS80/MX575C

4 | Introduction | HS80/MX575C User Manual Introduction Overview The HS80 GPS Compass and the MX575C DGPS Compass are based upon a new generation GPS engine technology. Figure 1-1: HS80/MX575C side view ¼ Note: When referring to both the HS80 G...

[Page 6] Simrad HS80/MX575C

| 5 Introduction | HS80/MX575C User Manual Parts list ¼ Note: The HS80/MX575C’s parts comply with IEC 60945 Section 4.4: “exposed to the weather.” The sections below list parts included in your HS80 kit and the MX575C kit. HS80 Parts list Pa...

[Page 7] Simrad HS80/MX575C

6 | Installation | HS80/MX575C User Manual Installation Mounting location This section provides information on determining the best location for the HS80/MX575C. GPS reception When considering where to mount the HS80/MX575C, consider the following...

[Page 8] Simrad HS80/MX575C

| 7 Installation | HS80/MX575C User Manual Environmental considerations The HS80/MX575C is designed to withstand harsh environmental conditions; however, adhere to the following limits when storing and using the GPS Compass: • Operating tempe...

[Page 9] Simrad HS80/MX575C

8 | Installation | HS80/MX575C User Manual Mounting orientation The HS/80/MX575C outputs heading, pitch, and roll readings regardless of the orientation of the antennas. However, the relation of the antennas to the boat’s axis determines wheth...

[Page 10] Simrad HS80/MX575C

| 9 Installation | HS80/MX575C User Manual Recessed arrow located on the bottom of the enclosure Forward motion Figure 2-3: Alternate orientation and resulting signs of HPR values HS80/MX575C alignment The top of the HS80/MX575C enclosure incorpor...

[Page 11] Simrad HS80/MX575C

10 | Installation | HS80/MX575C User Manual HS80/MX575C dimensions Figure 2-6 illustrates the physical dimensions of the HS80/MX575C. Figure 2-6: HS80/MX575C dimensions ...

[Page 12] Simrad HS80/MX575C

| 11 Installation | HS80/MX575C User Manual Power/Data cable considerations Before mounting the HS80/MX575C consider the following regarding power/data cable routing: • Cable must reach an appropriate power source • Cable may connect to a...

[Page 13] Simrad HS80/MX575C

12 | Installation | HS80/MX575C User Manual 4. Place the HS80/MX575C over the marks to ensure the planned hole centers align with the true hole centers (adjusting as necessary). 5. Use a center punch to mark the hole centers. 6. Drill the mount...

[Page 14] Simrad HS80/MX575C

| 13 Installation | HS80/MX575C User Manual Connecting the serial cable or Serial-to-NMEA 2000 adapter to the HS80/ MX575C After you mount the HS80/MX575C connect either the serial power/data cable or the serial- to-NMEA 2000 adapter to the HS80/MX5...

[Page 15] Simrad HS80/MX575C

14 | Installation | HS80/MX575C User Manual Connecting the Serial-to-NMEA 2000 adapter For more information on the serial-to-NMEA 2000 adapter see “NMEA 2000 port” on page 16. This adapter is an optional item for the MX575C model. 1. Align ...

[Page 16] Simrad HS80/MX575C

| 15 Installation | HS80/MX575C User Manual Ports The HS80/MX575C offers either NMEA 0183 serial port or NMEA 2000 port functionality. Serial ports The HS80/MX575C has three ports (Port A, Port B, and Port C), where: • Port A can be both full-...

[Page 17] Simrad HS80/MX575C

16 | Installation | HS80/MX575C User Manual Recommendations for connecting to other devices When interfacing to other devices, ensure the transmit data output from the HS80/MX575C is connected to the data input of the other device. The signal grou...

[Page 18] Simrad HS80/MX575C

| 17 Installation | HS80/MX575C User Manual 126996 Product Information NMEA 2000 database version supported, manufacturer’s product code, NMEA 2000 certification level, Load Equivalency number, and other product- specific information. B ...

[Page 19] Simrad HS80/MX575C

18 | Installation | HS80/MX575C User Manual PG No. (PGN) Description Level Default Update Rate (msec) Freq (Hz) 127258 Magnetic Variation Message for transmitting variation. The message contains a sequence number to allow synchronization of...

[Page 20] Simrad HS80/MX575C

| 19 Installation | HS80/MX575C User Manual PG No. (PGN) Description Level Default Update Rate (msec) Freq (Hz) 129539 GNSS DOPs Provides a single transmission containing GNSS status and dilution of precision components (DOP) that indicate th...

[Page 21] Simrad HS80/MX575C

20 | Installation | HS80/MX575C User Manual Connecting the HS80/MX575C to external devices ¼ Note: This section refers to a serial connection. For connecting external NMEA 2000 devices, plug the serial-to-NMEA 2000 adapter into the HS80 and the...

[Page 22] Simrad HS80/MX575C

| 21 Installation | HS80/MX575C User Manual Power/Data cable pin out specications Figure 2-10 shows the power/data cable pin out, and the table shows the cable’s pin out specifications. Figure 2-10: Power/data cable pin assignment Pin Functi...

[Page 23] Simrad HS80/MX575C

22 | Operation | HS80/MX575C User Manual Operation GPS overview For your convenience, both the GPS and SBAS operation of the HS80/MX575C features automatic operational algorithms. When powered for the first time, the HS80/MX575C performs a ‘col...

[Page 24] Simrad HS80/MX575C

| 23 Operation | HS80/MX575C User Manual Beacon operation Many marine authorities, such as the U.S. coast guard, have installed networks of radio beacon stations that broadcast DGPS corrections to users of this system. With the increasing utility o...

[Page 25] Simrad HS80/MX575C

24 | Operation | HS80/MX575C User Manual Supplemental sensors The HS80/MX575C has three supplemental sensors (gyro and two tilt sensors) that are integrated into the unit’s main PCB. The supplemental sensors are enabled by default. You can enabl...

[Page 26] Simrad HS80/MX575C

| 25 Operation | HS80/MX575C User Manual Gyro aiding The HS80/MX575C’s internal gyro offers several benefits. It reduces the sensor volume for an RTK solution. This shortens reacquisition times when a GPS heading is lost because the satellite s...

[Page 27] Simrad HS80/MX575C

26 | Operation | HS80/MX575C User Manual Heading time constant Use the $JATT,HTAU command to adjust the level of responsiveness of the true heading measurement provided in the $GPHDT message. The default value of this constant is 10.0 seconds of...

[Page 28] Simrad HS80/MX575C

| 27 Operation | HS80/MX575C User Manual Common commands and messages ¼ Note: When selecting your baud rate and message types use the following formula and example to calculate the bits/sec for each message and then sum the results to determine ...

[Page 29] Simrad HS80/MX575C

28 | Operation | HS80/MX575C User Manual Command Description $JRESET Reset unit’s configuration to firmware defaults ¼ Note: $JRESET clears all parameters. For the HS80/ MX575C you will have to issue the $JATT, FLIPBRD, YES command to prope...

[Page 30] Simrad HS80/MX575C

| 29 Operation | HS80/MX575C User Manual $GPRMC P 20 Hz Recommended minimum specific GNSS data Yes *$GPROT H 20 Hz GPS-derived rate of turn (ROT) *see last bullet in Note at end of this table Yes $GPRRE S 1 Hz Range residual and estimated posit...

[Page 31] Simrad HS80/MX575C

30 | Operation | HS80/MX575C User Manual Parameters specic to $JATT command Parameter Description Query Specify COGTAU Set/query COG time constant (0.0 to 3600.0 sec) X X CSEP Query antenna separation X EXACT Enable/disable internal filter re...

[Page 32] Simrad HS80/MX575C

| 31 Troubleshooting | HS80/MX575C User Manual Troubleshooting Table A-1 provides troubleshooting for common problems. Table A-1: Troubleshooting Symptom Possible Solution Receiver fails to power • Verify polarity of power leads • Check ...

[Page 33] Simrad HS80/MX575C

32 | Troubleshooting | HS80/MX575C User Manual Symptom Possible Solution No heading or incorrect heading value • Check CSEP value is fairly constant without varying more than 1 cm (0.39 in)—larger variations may indicate a high multipath...

[Page 34] Simrad HS80/MX575C

| 33 Technical specications | HS80/MX575C User Manual Technical specications Specications GPS sensor Item Specification Receiver type L1, C/A code with carrier phase smoothing Channels Two 12-channel, parallel tracking (Two 10-channel when...

[Page 35] Simrad HS80/MX575C

34 | Technical specications | HS80/MX575C User Manual Power Item Specification Input voltage 6 to 36 VDC Power consumption 3 W nominal Current consumption HS80 MX575C 320 mA @ 9 VDC 350 mA @ 9 VDC 240 mA @ 12 VDC 265 mA @ 12 VDC 180 mA @ 16 VDC ...

[Page 36] Simrad HS80/MX575C

| 35 Technical specications | HS80/MX575C User Manual Certications Heading Device IMO Resolution MSC.116(73) ISO 22090-3 Ed.1.0, 2004 incl. Corr. 1,2005 IMO Resolution A.694(17) IEC 60945 Ed.4.0, 2002 incl. Corr.1, 2008 IMO Resolution MSC.19...

[Page 37] Simrad HS80/MX575C

36 | Technical specications | HS80/MX575C User Manual Output messages The MX575C data output conforms to the NMEA 0183 V4.0 at 4800, 9600, or 19200 baud. Below is a list of the NMEA sentences output: NMEA 0183 data output sentences (1) GBS - G...

[Page 38] Simrad HS80/MX575C

| 37 Technical specications | HS80/MX575C User Manual (3) GLL – Geographic Position - Latitude/Longitude Latitude and Longitude of vessel position, time of position fix and status. $--GLL,llll.ll,a,yyyyy.yy,a,hhmmss.ss,A,a*hh<CR><LF&g...

[Page 39] Simrad HS80/MX575C

38 | Technical specications | HS80/MX575C User Manual (5) GST - GNSS Pseudorange Error Statistics This message is used to support Receiver Autonomous Integrity Monitoring (RAIM). Pseudorange measurement error statistics can be translated in th...

[Page 40] Simrad HS80/MX575C

| 39 Technical specications | HS80/MX575C User Manual (7) HDT – Heading, True Actual vessel heading in degrees (True) produced by any device or system producing true heading. $GPHDT,x.x,T*hh<CR><LF> 1 2 ¼ Notes: 1 Headin...

[Page 41] Simrad HS80/MX575C

40 | Technical specications | HS80/MX575C User Manual (9) ROT – Rate Of Turn Rate of turn and direction of turn. $GPROT,x.x,A*hh<CR><LF> 1 2 ¼ Notes: 1 Rate of turn, degrees/minute, “-“ = bow turns to port 2 Status: ...

[Page 42] Simrad HS80/MX575C

| 41 Technical specications | HS80/MX575C User Manual (12) ZDA - Time and Date UTC, day, month, year and local time zone $GPZDA,hhmmss,xx,xx,xxxx,xx,xx*hh<CR><LF> 1 2 3 4 5 6 ¼ Notes: 1 UTC 2, 3, 4 Day, month & y...

[Page 43] Simrad HS80/MX575C

42 | Technical specications | HS80/MX575C User Manual Proprietary Input data messages The table below gives a list of the available proprietary input messages and their description: Message type Description $PMVXG,303 RESET CONTROL $PMVXG,026 NME...

[Page 44] Simrad HS80/MX575C

| 43 Technical specications | HS80/MX575C User Manual Sentence type - $PMVXG,026 Description: NMEA Message Schedule This message enables/disables output of the specified sentence to the NMEA port and defines the output rate. Flow: Input $PMVX...

[Page 45] Simrad HS80/MX575C

44 | Technical specications | HS80/MX575C User Manual Sentence type: $PMVXG,200 Description: Set Port Configuration This message sets the transmission rate, number of data bits, and parity convention for each of the serial interface ports. Flo...

[Page 46] Simrad HS80/MX575C

| 45 Technical specications | HS80/MX575C User Manual Sentence type: $GPMSK Description: Beacon tune command There are three main derivatives of this command that affects the method of beacon receiver tuning, and each are described in the follow...

[Page 47] Simrad HS80/MX575C

46 | Technical specications | HS80/MX575C User Manual Automatic beacon search command ($GPMSK,305): This command initiates the beacon receiver to automatic mode of operation in which the receiver operates without operator intervention, selecting...

[Page 48] Simrad HS80/MX575C

| 47 Technical specications | HS80/MX575C User Manual Sentence type: $JSHOW Description: Command to show its current configuration. This command is used to poll the MX575 receiver for its current configuration. This command has the following str...

[Page 49] Simrad HS80/MX575C

48 | Technical specications | HS80/MX575C User Manual Line Description 14 This line indicates the current frequency of the L-band receiver 15 This line indicates the current maximum acceptable differential age in seconds When issuing this comm...

[Page 50] Simrad HS80/MX575C

| 49 Technical specications | HS80/MX575C User Manual Sentence type: $JDIFF Description: Beacon receiver differential mode This command is used to change the differential mode of the receiver. The default differential mode is Auto/Database. T...

[Page 51] Simrad HS80/MX575C

50 | Wiring Diagrams | HS80/MX575C User Manual Wiring Diagrams MX420 CDU to MX575C interface diagram RL1 RL2 RS232 enable J1 UPPER LOWER Rs232 PORT 2 Tx Rx GND MX420/2 JUNCTION BOX CABLE A MX ANTENNA PORT PORT1 DUAL CONTROL EXT. ALARM POWER FAIL PWR...

[Page 52] Simrad HS80/MX575C

| 51 Wiring Diagrams | HS80/MX575C User Manual HS80/MX575C interface via MX510 junction Box IN+ IN- A in B in B out A out RED BLK GRN ORG BRN BLU WHT YEL PUR GRY A in A out B in B out A in A out B in B ...

[Page 53] Simrad HS80/MX575C

52 | Wiring Diagrams | HS80/MX575C User Manual MX512 to MX575C interface diagram via MX512 Junction Box MOB PWR FAIL N.C. PWR FAIL C PWR FAIL MOB P O R T 1 M X 4 2 1 SPEE D LOG E X T . A L A R M G P I O 1 G P I O 2 G P I O 3 P 0 R T 4 P O R T 5 P O...

[Page 54] Simrad HS80/MX575C

| 53 Wiring Diagrams | HS80/MX575C User Manual 1PPS output of MX575C BLK (-) YEL/BLK (Port B TX-) YEL (Port B TX+) BLK/BRN (Port B RX-) BRN (Port B RX+ HS80/MX575C BLK/GRN (Port A TX-) GRN (Port A TX+) ORG (1 PPS+) *ORG/BLK (1 PPS-) +12-24 VDC ...

[Page 55] Simrad HS80/MX575C

*988-10221-001* ...