Matrix VS-S72 Seated Leg Curl Owner's Manual

[Page 1] Matrix VS-S72 Seated Leg Curl

OWNERS MANUAL Versa Single-Station Strength VS-S72 Seated Leg Curl ...

[Page 2] Matrix VS-S72 Seated Leg Curl

Table Of Contents Safety, General Care & Maintenence .................................................3 Getting Started (Product Specifications) ..........................................5 Assembly Information .......................................

[Page 3] Matrix VS-S72 Seated Leg Curl

3 IMPORTANT SAFETY INSTRUCTIONS IMPORTANT SAFETY INFORMATION It is the sole responsibility of the purchaser of Matrix products to instruct all individuals, whether they are the end user or supervis- ing personnel on proper usage of the equipment. It ...

[Page 4] Matrix VS-S72 Seated Leg Curl

4 IMPORTANT SAFETY INSTRUCTIONS WARNING: This product contains chemicals known to the State of Califor- nia to cause cancer and birth defects or other reproductive harm. WARNING: SERIOUS INJURY CAN OCCUR ON THIS EQUIPMENT. FOLLOW THESE PRECAUTIONS T...

[Page 5] Matrix VS-S72 Seated Leg Curl

5 GETTING STARTED TECH SPECS Overall dimensions 71”L X 45”W X 66”H Weight Light Stack = 556 lbs (253 kg), Heavy Stack = 606 lbs (275 kg) Shipping weight 406 lbs (184 kg) WARRANTY (Valid in USA only) Frame (not coatings) 10 years Structural pa...

[Page 6] Matrix VS-S72 Seated Leg Curl

6 ASSEMBLY UNPACKING | TOOLS REQUIRED UNPACKING Thank you for purchasing a Matrix product. This machine is an EN957-1 and EN957-2 compliant Class S product. Your Ma- trix product is inspected before it is packaged. It is shipped in multiple pieces to...

[Page 7] Matrix VS-S72 Seated Leg Curl

7 MARKINGS WARNING LABEL LOCATIONS ...

[Page 8] Matrix VS-S72 Seated Leg Curl

8 Parts List ID DESCRIPTION QTY 1 Inner User Frame 1 2 M10 Nylock Nut 11 3 M10 Flat Washer 40 4 Outer User Frame 1 5 Wide Cupped Flange 3 6 M10 X 125L Socket Head Cap Screw 6 7 Middle Connecting Tube 2 8 M10 X 80L Socket Head Cap Screw 4 9 M10 X 15L ...

[Page 9] Matrix VS-S72 Seated Leg Curl

9 ID DESCRIPTION QTY 34 Back Pad Adjustment Tube 1 35 Plug 2 36 Thigh Pad Adjustment Assembly 1 37 Thigh Pad 1 39 Black Pivot Cover 1 39 Front Shroud 1 40 Rear Shroud 1 41 M8 X 25L SHC 4 43 Large M8 Flat Washer (Ø20 mm) 4 43 Top Cap 1 44 Top Cap Cov...

[Page 10] Matrix VS-S72 Seated Leg Curl

10 PART 1: USER FRAME ASSEMBLY STEP 1 | USER FRAME INSTRUCTIONS & NOTES 3 1 2 4 5 6 ID DESCRIPTION QUANTITY 1 Inner User Frame 1 2 M10 Nylock Nut 2 3 M10 Flat Washer 4 4 Outer User Frame 1 5 Wide Cupped Flange 1 6 M10 X 125L SHC 2 Instal...

[Page 11] Matrix VS-S72 Seated Leg Curl

11 ASSEMBLY STEP 2 | USER FRAME ASSEMBLY INSTRUCTIONS & NOTES PART 1: USER FRAME ASSEMBLY ID DESCRIPTION QUANTITY 2 M10 Nylock Nut 4 3 M10 Flat Washer 8 5 Wide Cupped Flange 1 6 M10 X 125L SHC 2 7 Mid Connecting Tube 1 8 M10 X 80L SHC 2 Install t...

[Page 12] Matrix VS-S72 Seated Leg Curl

12 PART 2: CAM ASSEMBLY STEP 1 | CAM ASSEMBLY INSTRUCTIONS & NOTES ID DESCRIPTION QUANTITY 9 M10 X 15L SHC 1 10 M10 Flat Washer (Ø42 mm) 1 11 Key (8 X 10 mm) 1 12 CAM 1 13 Wave (Spring) Washer 2 14 Flat Washer (Ø45 mm OD/Ø30 mm ID) 1 15 Axle...

[Page 13] Matrix VS-S72 Seated Leg Curl

13 9 10 11 12 13 13 14 15 9 10 11 12 13 13 14 15 ASSEMBLY STEP 1 | WEIGHT STACK TO USER FRAME ASSEMBLY INSTRUCTIONS & NOTES PART 3: STACK & USER FRAME ASSEMBLY 3 16 3 16 ID DESCRIPTION QUANTITY 3 M10 Flat Washer 2 16 M10...

[Page 14] Matrix VS-S72 Seated Leg Curl

14 ASSEMBLY STEP 2 | WEIGHT STACK TO USER FRAME ASSEMBLY INSTRUCTIONS & NOTES PART 3: STACK & USER FRAME ASSEMBLY 3 16 17 2 5 6 ID DESCRIPTION QUANTITY 2 M10 Nylock Nut 2 3 M10 Flat Washer 8 6 M10 X 125L SHC 2 5 Wide Cupped Flange 1 16...

[Page 15] Matrix VS-S72 Seated Leg Curl

15 PART 3: STACK & USER FRAME ASSEMBLY STEP 3 | WEIGHT STACK TO USER FRAME ASSEMBLY INSTRUCTIONS & NOTES 2 3 18 16 19 ID DESCRIPTION QUANTITY 2 M10 Nylock Nut 2 3 M10 Washer 8 16 M10 X 20L SHC 4 18 Narrow Cupped Flange 1 19 M10 X 100L S...

[Page 16] Matrix VS-S72 Seated Leg Curl

16 PART 4: CABLE ASSEMBLY STEP 1 | WEIGHT STACK CABLE ASSEMBLY INSTRUCTIONS & NOTES View A Cable tension is adjusted by raising or lowering pulley as shown in View A. Note: Nuts for adjustable pulley must be on inside towards weight plates. ASSEM...

[Page 17] Matrix VS-S72 Seated Leg Curl

17 ASSEMBLY STEP 1 | EXERCISE ARM ASSEMBLY INSTRUCTIONS & NOTES PART 5: EXERCISE ARM ASSEMBLY Torque item 24 to: 39 N-m/29 ft-lbs. 21 20 10 16 23 22 24 21 20 10 16 Torque item 16 to: 77 N-m/57 ft-lbs. ID DESCRIPTION QUANTITY 10 M10 Fl...

[Page 18] Matrix VS-S72 Seated Leg Curl

18 ASSEMBLY STEP 2 | ANKLE ARM & PAD ASSEMBLY INSTRUCTIONS & NOTES PART 5: EXERCISE ARM ASSEMBLY ID DESCRIPTION QUANTITY 2 M10 Nylock Nut 1 3 M10 Flat Washer 2 19 M10 X 100L SHC 1 24 M8 X 15L SHC 1 25 Axle 1 26 Ankle Pad Weldment 1 27 Ankle P...

[Page 19] Matrix VS-S72 Seated Leg Curl

19 STEP 1 | PAD ASSEMBLY INSTRUCTIONS & NOTES 30 16 ID DESCRIPTION QUANTITY 16 M10 X 20L SHC 4 30 Pad 1 Install the pad as shown. Tighten to 57 N-m/41 ft-lbs. ASSEMBLY PART 6: PAD ASSEMBLY ...

[Page 20] Matrix VS-S72 Seated Leg Curl

20 ASSEMBLY STEP 2 | BACK PAD ASSEMBLY INSTRUCTIONS & NOTES PART 6: PAD ASSEMBLY ID DESCRIPTION QUANTITY 3 M10 Flat Washer 4 8 M10 X 80L SHC 2 31 Back Pad 1 32 Back Pad Mounting Tube 1 33 M10 X 75L SHC 2 34 Back Pad Adjustment Tube 1 3 34 8 3...

[Page 21] Matrix VS-S72 Seated Leg Curl

21 ASSEMBLY PART 6: PAD ASSEMBLY STEP 3 | BACK PAD ASSEMBLY INSTRUCTIONS & NOTES 3. Remove Limit Pin. 4. Raise Pull Pin to assemble entire Back Pad assembly. 5. Re-assemble Limit Pin. 3 4 5 ...

[Page 22] Matrix VS-S72 Seated Leg Curl

22 STEP 1 | THIGH PAD ASSEMBLY ASSEMBLY INSTRUCTIONS & NOTES ID DESCRIPTION QUANTITY 16 M10 X 20L 2 35 Plug 2 36 Thigh Pad Adjustment Assembly 1 37 Thigh Pad 1 ASSEMBLY PART 7: THIGH PAD ASSEMBLY 36 37 16 35 Torque hardware to 57 N-m/41 ft-l...

[Page 23] Matrix VS-S72 Seated Leg Curl

23 10 38 16 STEP 1 | PAD ASSEMBLY INSTRUCTIONS & NOTES ID DESCRIPTION QUANTITY 10 M10 Flat Washer (Ø42 mm) 1 16 M10 X 20L SHC 1 38 Black Pivot Cover 1 ASSEMBLY PART 7: PAD ASSEMBLY ...

[Page 24] Matrix VS-S72 Seated Leg Curl

24 STEP 1 | SHROUD ASSEMBLY ASSEMBLY INSTRUCTIONS & NOTES PART 8: PLASTICS ASSEMBLY ID DESCRIPTION QUANTITY 39 Front Shroud 1 40 Rear Shroud (Not shown) 1 ASSEMBLY Install the weight stack shrouds as shown. 39 Position hangers in their lowest p...

[Page 25] Matrix VS-S72 Seated Leg Curl

25 STEP 2 | TOP CAP ASSEMBLY INSTRUCTIONS & NOTES ID DESCRIPTION QUANTITY 41 M8 X 25L SHC 4 42 M8 Flat Washer (20 mm diameter) 4 43 Top Cap 1 42 41 43 ASSEMBLY PART 8: PLASTICS ASSEMBLY Install the top cap onto the weight stack as shown. Torq...

[Page 26] Matrix VS-S72 Seated Leg Curl

26 STEP 3 | TOP CAP COVERS INSTRUCTIONS & NOTES ID DESCRIPTION QUANTITY 44 Top Cap Cover 2 44 44 ASSEMBLY PART 8: PLASTICS ASSEMBLY Install the top cap covers. ...

[Page 27] Matrix VS-S72 Seated Leg Curl

27 ASSEMBLY PART 9: PREMIUM KIT ASSEMBLY PREMIUM KIT ASSEMBLY INSTRUCTIONS & NOTES ID DESCRIPTION QUANTITY 1P Wing 1 2P Rep Counter 1 3P Towel Hook 1 4P ASG Pull Grip 2 5P Premium Pullpin 4 1P 2P 3P 4P 5P IMPORTANT NOTICE PLEASE NOTE: Be sure to...

[Page 28] Matrix VS-S72 Seated Leg Curl

28 STEP 1 | PREMIUM KIT ASSEMBLY INSTRUCTIONS & NOTES PART 9: PREMIUM KIT ASSEMBLY 1. Remove the (2) top cap covers using a flat blade screw driver. 2. Remove the (4) M8 bolts and 20 mm diameter washers that hold the top cap to the weight sta...

[Page 29] Matrix VS-S72 Seated Leg Curl

29 ASSEMBLY STEP 2 | PREMIUM KIT ASSEMBLY INSTRUCTIONS & NOTES PART 9: PREMIUM KIT ASSEMBLY Rep Counter - Sensors 1. Assemble Rep Counter sensor base using (4) screws included with the kit. 2. Assemble (3) sensors located per machine chart sh...

[Page 30] Matrix VS-S72 Seated Leg Curl

30 STEP 3 | PREMIUM KIT ASSEMBLY INSTRUCTIONS & NOTES PART 9: PREMIUM KIT ASSEMBLY 1. Remove and discard hole caps using caution not to scratch the paint. 2. Attach plug to Rep Counter. 3. Assemble Towel Hook (3P) and Rep Counter (2P) using ...

[Page 31] Matrix VS-S72 Seated Leg Curl

31 ASSEMBLY STEP 4 | PREMIUM KIT ASSEMBLY INSTRUCTIONS & NOTES PART 9: PREMIUM KIT ASSEMBLY Assemble the wing (1P) as shown using the M8 hardware provided with the kit. Tighten to 39 N-m (29 ft-lbs.). Wing ...

[Page 32] Matrix VS-S72 Seated Leg Curl

32 STEP 5 | PREMIUM KIT ASSEMBLY INSTRUCTIONS & NOTES PART 9: PREMIUM KIT ASSEMBLY 1. Remove the end caps using a 3 mm Allen wrench. 2. Cut off and discard the grips. 3. Remove inner collars with a 3 mm allen wrench. 4. Assemble the ASG grip ...

[Page 33] Matrix VS-S72 Seated Leg Curl

33 ASSEMBLY STEP 6 | PREMIUM KIT ASSEMBLY INSTRUCTIONS & NOTES PART 9: PREMIUM KIT ASSEMBLY Pull Pin Remove the four pull pins using an adjustable wrench, and replace with the Premium pull pins making sure that the pull pin lengths are correct f...

[Page 34] Matrix VS-S72 Seated Leg Curl

...

[Page 35] Matrix VS-S72 Seated Leg Curl

...

[Page 36] Matrix VS-S72 Seated Leg Curl

Matrix Fitness 1600 Landmark Drive Cottage Grove WI 53527 matrixfitness.com Toll-free 866.693.4863 Facsimilie 608.839.8687 Versa Seated Leg Curl Owners Guide Rev.1.2 Copyright © 2013 Matrix Fitness ...